• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.491-496
• /
• 2011

Transparent conducting oxides (TCOs) used in the antireflection layer and current spreading layer of heterojunction solar cells should have excellent optical and electrical properties. Furthermore, TCOs need a high work function over 5.2 eV to prevent the effect of emitter band-bending caused by the difference in work function between emitter and TCOs. Sn-doped $In_2O_3$ (ITO) film is a highly promising material as a TCO due to its excellent optical and electrical properties. However, ITO films have a low work function of about 4.8 eV. This low work function of ITO films leads to deterioration of the conversion efficiency of solar cells. In this work, ITO films with various Zn contents of 0, 6.9, 12.7, 28.8, and 36.6 at.% were fabricated by a co-sputtering method using ITO and AZO targets at room temperature. The optical and electrical properties of Zn-doped ITO thin films were analyzed. Then, silicon heterojunction solar cells with these films were fabricated. The 12.7 at% Zn-doped ITO films show the highest hall mobility of 35.71 $cm^2$/Vsec. With increasing Zn content over 12.7, the hall mobility decreases. Although a small addition of Zn content increased the work function, further addition of Zn content over 12.7 at.% led to decreasing electrical properties because of the decrease in the carrier concentration and hall mobility. Silicon heterojunction solar cells with 12.7 at% Zn-doped ITO thin films showed the highest conversion efficiency of 15.8%.

• Current Optics and Photonics
• /
• v.6 no.4
• /
• pp.367-374
• /
• 2022

A photodetector based on a reduced graphene oxide (RGO)/n-Si heterojunction with high responsivity, detectivity and fast response speed is presented. Here, we put forward a simple vacuum filtration method to prepare RGO film and transfer it onto an n-Si substrate to form an RGO/n-Si heterojunction. The experimental results show that the heterojunction has good rectification characteristics, and the response and recovery time are less than 0.31 s and 0.25 s, respectively. Under 470 nm light conditions at -2 V applied voltage, the responsivity and detectivity of the device are 65 mA/W and 4.02 × 10¹⁰ cmHz^1/2W^-1, respectively. The simple preparation process and good performance of the RGO/n-Si heterojunction make it a promising material for photoelectric detection, especially in the near-ultraviolet band.

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.341-346
• /
• 2011

In this study, we inserted a Zn buffer layer into a AZO/p-type a-si:H layer interface in order to lower the contact resistance of the interface. For the Zn layer, the deposition was conducted at 5 nm, 7 nm and 10 nm using the rf-magnetron sputtering method. The results were compared to that of the AZO film to discuss the possibility of the Zn layer being used as a transparent conductive oxide thin film for application in the silicon heterojunction solar cell. We used the rf-magnetron sputtering method to fabricate Al 2 wt.% of Al-doped ZnO (AZO) film as a transparent conductive oxide (TCO). We analyzed the electro-optical properties of the ZnO as well as the interface properties of the AZO/p-type a-Si:H layer. After inserting a buffer layer into the AZO/p-type a-Si:H layers to enhance the interface properties, we measured the contact resistance of the layers using a CTLM (circular transmission line model) pattern, the depth profile of the layers using AES (auger electron spectroscopy), and the changes in the properties of the AZO thin film through heat treatment. We investigated the effects of the interface properties of the AZO/p-type a-Si:H layer on the characteristics of silicon heterojunction solar cells and the way to improve the interface properties. When depositing AZO thin film on a-Si layer, oxygen atoms are diffused from the AZO thin film towards the a-Si layer. Thus, the characteristics of the solar cells deteriorate due to the created oxide film. While a diffusion of Zn occurs toward the a-Si in the case of AZO used as TCO, the diffusion of In occurs toward a-Si in the case of ITO used as TCO.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.117-123
• /
• 2014

The fabrication and characterization of a Si/ZnO thin film heterojunction ultraviolet photodiode has been presented in this paper. ZnO thin film of ~100 nm thick was deposited on <100> Silicon (Si) wafer by atomic layer deposition (ALD) technique. The Photoluminescence spectroscopy confirms that as-deposited ZnO thin film has excellent visible-blind UV response with almost no defects in the visible region. The room temperature current-voltage characteristics of the n-ZnO thin film/p-Si photodiodes are measured under an UV illumination of $650{\mu}W$ at 365 nm in the applied voltage range of ${\pm}2V$. The current-voltage characteristics demonstrate an excellent UV photoresponse of the device in its reverse bias operation with a contrast ratio of ~ 1115 and responsivity of ~0.075 A/W at 2 V reverse bias voltage.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.05a
• /
• pp.19.2-19.2
• /
• 2007

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.55-59
• /
• 2020

Copper Oxide (CuO) films were deposited on the n-type silicon wafer by rf magnetron sputtering for heterojunction solar cells. And then the samples were treated as a function of the annealing temperature (300-600℃) in a vacuum. Their electrical, optical and structural properties of the fabricated heterojunction solar cells were then investigated and the power conversion efficiencies (PCE) of the fabricated p-type copper oxide/n-type Si heterojunction cells were measured using solar simulator. After being treated at temperature of 500℃, the solar cells with CuO film have PCE of 0.43%, Current density of 5.37mA/㎠, Fill Factor of 39.82%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.8
• /
• pp.481-485
• /
• 2015

We investigated the effects of annealing on the electrical and thermal properties of ZTO/4H-SiC heterojunction diodes. A ZTO thin film layer was grown on p-type 4H-SiC substrate by using solution process. The ZTO/SiC heterojunction structures annealed at $500^{\circ}C$ show that $I_{on}/I_{off}$ increases from ${\sim}5.13{\times}10^7$ to ${\sim}1.11{\times}10^9$ owing to the increased electron concentration of ZTO layer as confirmed by capacitance-voltage characteristics. In addition, the electrical characterization of ZTO/SiC heterojunction has been carried out in the temperature range of 300~500 K. When the measurement temperature increased from 300 K to 500 K, the reverse current variation of annealed device is higher than as-grown device, which is related to barrier height in the ZTO/SiC interface. It is shown that annealing process is possible to control the electrical characteristics of ZTO/SiC heterojunction diode.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.2
• /
• pp.119-123
• /
• 2006

This work presents the fabrication and characteristics of $Bi_2O_3/Si$ heterojunction prepared by rapid thermal oxidation technique without any postdeposition annealing condition. The bismuth trioxide film was deposited onto monocrystalline Si and glass substrates by rapid thermal oxidation of bismuth film with aid of halogen lamp at $500^{\circ}C/\;45$ s in static air. The structural, optical and electrical properties of $Bi_2O_3$ film were investigated and compared with other published results. The structural investigation showed that the grown films are polycrystalline and multiphase (${\alpha}-Bi_2O_3$ and ${\beta}-Bi_2O_3$). Optical properties revealed that these films having direct optical band gap of 2.55 eV at 300 K with high transparency in visible and NIR regions. Dark and illuminated I-V, CV, and spectral responsivity of $Bi_2O_3/Si$ heterojunction were investigated and discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.99.2-99.2
• /
• 2010

This paper investigates the dependence of a-Si:H/c-Si passivation and heterojunction solar cell performances on various cleaning processes of silicon wafer and surface morphology. It is observed that passivation quality of a-Si:H thin-films on c-Si wafer highly depends on wafer surface conditions. The MCLT(Minority carrier life time) of wafer incorporating intrinsic (i) a-Si:H as a passivation layer shows sensitive variation with cleaning process and surface morpholgy. By applying improved cleaning processes and surface morphology we can obtain the MCLT of $200{\mu}sec$ after H-termination and above 1.5msec after i a-Si:H thin film deposition, which has implied open circuit voltage of 0.720V.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.432-432
• /
• 2008