• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1826-1829
• /
• 2005

Recent advancement in wireless communications and electronics has enabled the development of low power sensor network. Wireless sensor network are often used in remote monitoring control applications, health care, security and environmental monitoring. Wireless sensor networks are an emerging technology consisting of small, low-power, and low-cost devices that integrate limited computation, sensing, and radio communication capabilities. Sensor network platform for health care has been designed, fabricated and tested. This system consists of an embedded micro-controller, Radio Frequency (RF) transceiver, power management, I/O expansion, and serial communication (RS-232). The hardware platform uses Atmel ATmega128L 8-bit ultra low power RISC processor with 128KB flash memory as the program memory and 4KB SRAM as the data memory. The radio transceiver (Chipcon CC1000) operates in the ISM band at 433MHz or 916MHz with a maximum data rate of 76.8kbps. Also, the indoor radio range is approximately 20-30m. When many sensors have to communicate with the controller, standard communication interfaces such as Serial Peripheral Interface (SPI) or Integrated Circuit ($I^{2}C$) allow sharing a single communication bus. With its low power, the smallest and low cost design, the wireless sensor network system and wireless sensing electronics to collect health-related information of human vitality and main physiological parameters (ECG, Temperature, Perspiration, Blood Pressure and some more vitality parameters, etc.)

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.165-168
• /
• 2002

As the demand for higher data-rate chip-to-chip communication such as memory-to-controller, processor-to-processor increases, low cost high-speed serial links\ulcorner become more attractive. This paper describes a 0.25-fm CMOS 1.6Gbps/pin 4-level transceiver using Stub Series Terminated Logic for high Bandwidth. For multi-gigabit/second application, the data rate is limited by Inter-Symbol Interference (ISI) caused by channel low pass effects, process-limited on-chip clock frequency, and serial link distance. The proposed transceiver uses multi-level signaling (4-level Pulse Amplitude Modulation) using push-pull type, double data rate and flash sampling. To reduce Process-Voltage-Temperature Variation and ISI including data dependency skew, the proposed high-speed calibration circuits with voltage swing controller, data linearity controller and slew rate controller maintains desirable output waveform and makes less sensitive output. In order to detect successfully the transmitted 1.6Gbps/pin 4-level data, the receiver is designed as simultaneous type with a kick - back noise-isolated reference voltage line structure and a 3-stage Gate-Isolated sense amplifier. The transceiver, which was fabricated using a 0.25 fm CMOS process, performs data rate of 1.6 ~ 2.0 Gbps/pin with a 400MHB internal clock, Stub Series Terminated Logic ever in 2.25 ~ 2.75V supply voltage. and occupied 500 * 6001m of area.

• Journal of Sensor Science and Technology
• /
• v.14 no.6
• /
• pp.415-422
• /
• 2005

Using stretch sensors, a stuttering treatment training device that improve the abnormal breathing of stutterer was designed and developed. To improve stutterer's inadequate breathing method that is one of principal reason of stammering, the device estimates breathing method by checking the changes of the stretch sensor's resistances those are put on the chest and abdomen of user. And a vocal exercise program that carry out exercises only when the user maintains the abdominal breathing was designed. Using a PIC16C711 device that includes an A/D convertor, a main controller was designed and the vocal exercises software was developed using Director and C program with graphic user interface for user convenience. The controller sends the resistance data of sensors to PC through the serial port and the software verifies the breathing method. And the device was designed that the RTS (request to send) pin of serial port in PC is used as a power source so that it can work without any battery or other power source. Three stutterers have carried out the clinical experiments using the implemented device for two months and the results showed it was excellent to alleviate the stuttering.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.5
• /
• pp.746-755
• /
• 2009

Recently, NMEA2000 became the de facto standard of the communication protocol for the instrument level network in vessels, and it is anticipated that most of the vessels will be equipped with the sensors and actuators based on this protocol. The conventional serial communication specifications such as RS-232, RS-485, or even NMEA0183 are single-talker/multiple-listener and interconnection among multiple sensors and/or actuators usually results in a bundle of wires. On the other hand, NMEA2000 is a true bus type(multiple-talker/multiple-listener) protocol and theoretically up to 256 instruments can be hot-plugged. With the advent of the protocol, it is necessary to consider a new type of monitoring system for the instruments in vessels: In most traditional serial communication environments, a dedicated monitor or user interface was necessary for each sensor or actuator as it was simply not easy to collect data in a single place. With NMEA2000, the collection of various types of information is simple. An embedded system can be employed to combine, to arrange and to display informations from various types of devices. Assuming that the actuators and sensors on a vessel are interconnected by NMEA2000 standard, we devise a tentative interactive vessel monitoring system in which the following 4 kinds of informations are collected and delivered: the navigation, engine, weather and tanks informations.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.246-252
• /
• 2011

A high-voltage power supply has been built for activation of the brain via stimulation using a Full Wave Cockroft-Walton Circuit (FWCW). A resonant half-bridge inverter was applied (with half plus/half minus DC voltage) through a bidirectional power transistor to a magnetic stimulation device with the capability of producing a variety of pulse forms. The energy obtained from the previous stage runs the transformer and FW-CW, and the current pulse coming from the pulse-forming circuit is transmitted to a stimulation coil device. In addition, the residual energy in each circuit will again generate stimulation pulses through the transformer. In particular, the bidirectional device modifies the control mode of the stimulation coil to which the current that exceeds the rated current is applied, consequently controlling the output voltage as a constant current mode. Since a serial resonant half-bridge has less switching loss and is able to reduce parasitic capacitance, a device, which can simultaneously change the charging voltage of the energy-storage condenser and the pulse repetition rate, could be implemented. Image processing of the brain activity was implemented using a graphical user interface (GUI) through a data mining technique (data mining) after measuring the vital signs separated from the frequencies of EEG and ECG spectra obtained from the pulse stimulation using a 90S8535 chip (AMTEL Corporation).

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.501-511
• /
• 2023

This paper introduces and analyzes SAE J2716 SENT (Single Edge Nibble Transmission) protocol, a technical standard for serial transmission of digital sensor data in automotive applications. SENT can transmit both high-speed sensor data and low-speed sensor data in one data frame and has a total of 6 transmission modes, including 3 high-speed channel modes and 3 low-speed channel modes. In this paper, a SENT controller that supports all six modes of the SENT protocol was designed in Verilog HDL, implemented in FPGA, and verified with an oscilloscope and PC.

• The Journal of the Korea Contents Association
• /
• v.10 no.12
• /
• pp.10-17
• /
• 2010

In this paper, we design digital D-PHY link chip controling DSI (Display Serial Interface) that meets MIPI (Mobile Industry Processor Interface) standard. The D-PHY supports a high-speed (HS) mode for fast data traffic and a low-power (LP) mode for control transactions. For low power consumption, the unit blocks in digital D-PHY are optionally switched using the clock gating technique. The proposed low power digital D-PHY is simulated and compared with conven tional one about power consumption on each transaction mode. As a result, power consumptions of TX, RX, and total in HS mode decrease 74%, 31%, and 50%, respectively. In LP mode, power reduction rates of TX, RX, and total are 79%, 40%, and 51.5%, separately. We implemented the low power MIPI D-PHY digital chip using $0.13-{\mu}m$ CMOS process under 1.2V supply.

• The KIPS Transactions:PartA
• /
• v.9A no.1
• /
• pp.53-60
• /
• 2002

This paper describes a Gray Mode Graphic STN LCD drive circuit using USB interface. The drive circuit using USB interface can highly transfer image data created under PC t LCD. Hence, the LCD drive circuit doesn't use microprocessor for the convenience of users. The proposed LCD drive circuit part have been verified by simulation and by ALTERA EPF10K10TC144-3 FPGA implementation in VHDL. The USB interface part have been programmed in MS-Visual C++ 6.0. The validity and efficiency of the proposed LCD drive circuit have been verified by test board. After comparing this LCD drive circuit to specify it was verified that the developed LCD drive circuit showed good performances, such as convenience of users, low cost.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1A
• /
• pp.93-98
• /
• 2004

Serial ATA interface Is inexpensive comparatively and performance is superior. So it is suitable technology in demand that now require data transmission and throughput of high speed. This paper describes a design and implementation of Serial ATA Link layer about error detection and 8b/10b encoder/decoder for DC balance in frequency 150MHz. The 8b/10b Encoder is partitioned into a 5b/6b plus a 3b/4b coder. The logical model of the block is described by using Verilog HDL at register transistor level and the verified HDL is synthesized using standard cell libraries. And it is fabricated with $0.35{\mu}m$ Standard CMOS Cell library and the chip size is about $1500{\mu}m\;*\;1500{\mu}m$. The function of this chip has been verified and tested using testboard with FPGA equipment and IDEC ATS2 test equipment. It is used to frequency of 100MHz in verification processes and supply voltage 3.3V. The result of testing is well on the system clock 100MHz. The designed and verified each blocks may be used IP in the field of high speed serial data communication.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.284-287
• /
• 2000

Recently, developing medical devices have a tendency becoming the module for satisfying user's mutual complex needs. Because the most effective method for the observation of patients condition a diagnosis and a treatment is collecting data from various devices and controling operation following it. Module tendency is more popular due to manage easily totally many individual systems. This study implemented communication protocol to control by one control system connecting modular medical devices. Implemented system consist of one master module controlling all module and managing communication and many Slave modules. Communication between each modules introduced SPI(Serial Peripheral Interface) among many synchronous serial communication methods for the exact transmission and receipt of data. All communication executes by packet format. This can detect error. And, this protocol introduced PNP(Plug And Play) function that auto-detect connecting or removing module during running. This protocol exactly transmitted and received in faster speed more than 1Mbps. And in practical application to the ventilator this confirmed to give and take real-time data. And various functions by th central control system is implemented in this protocol.