• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.11
• /
• pp.617-624
• /
• 2000

The negative weight can be ofter seen in Hopfield neural network, which is difficult to implement negative conductance in circuits. Usually, the inverted output of amplifier is used to avoid negative resistors for expressing the negative weights in hardware implementation. However, there is some difference between using negative resistor and the inverted output of amplifier for representing the negative weight. This difference is discussed in this paper.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.1007-1012
• /
• 2002

In this paper, a regeneration inverter is proposed using 3-level inverter. Electric regeneration means regeneration brake in electric railway vehicles. Induction motors, generally used with railway vehicles, convert the electric energy to the movement energy when vehicle is running. When the vehicle stop, the induction motor convert the movement energy to the electric energy. Usually, this energy is used with another running vehicle in the same section. If there is no vehicle around when the regeneration is occurred, regeneration energy is consumed by heat energy with resistors. The proposed inverter is capable of reuse this regeneration energy in another place.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.12
• /
• pp.472-479
• /
• 1984

In order to realize the simple and economic 3rd order LPF using switched-capacitor(SC), we proposed the 3rd order RC LPF using a OP amplifier and realized the 3rd order SC LPF by replacing all the resistors in the RC LPF to SC. The frequency response of SC LPF was compared with the that of RC LPF. As a result, it was found that the response of realized SC LPF is almost similar to that of RC LPF.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.571-574
• /
• 2000

A complex coefficient filter obtained by directly exchanging several reactance elements included in a real coefficient, filter for imaginary valued resistors is described. By using the proposed method, four varieties of complex coefficient filter are obtained. The stability problem is described. Finally, the frequency responses of the proposed kiters are shown.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.8
• /
• pp.1733-1739
• /
• 1997

An ultra-compact milimeter-wave broadband MMIC amplifier was designed using a direct-coupled topology combined with optimum feedback design. Significant reductionin the chip size was possible by employing the direct-coupled topology. Bias resistors required for the direct-coupled topology were also used as feedback elements. Feedback was optimized for millimeter-wave frequencies using reactive elements. The fabricated MMIC amplifier was realized in a chip size of 0.8mm$^{[-992]}$ and showed gains higher than 8 dB from 12 to 44 GHz. An output power of 30mW was achieved at 44 GHz with a drain efficiency of 10%.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.50-52
• /
• 2019

Dynamic resistance equalization is a viable technique to balance SOC of cells in a parallel-connected battery configuration due to high equalization performance, simplicity and low-cost. However, an inappropriate design of the equalization resistor can degrade the equalization performance and increase the power loss. This paper proposes an optimization process to design the equalization resistors to minimize power loss and equalization error. The simulation results show that the optimally designed resistor significantly enhance the performance in comparison with the conventional fixed-resistor equalization.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1923-1930
• /
• 2004

This paper presents digital microflow controllers(DMFC), where a fluidic digital-to-analog converter(DAC) is used to achieve high-linearity, fine-level flow control for applications to precision biomedical dosing systems. The fluidic DAC, composed of binary-weighted flow resistance, controls the flow-rate based on the ratio of the flow resistance to achieve high-precision flow-rate control. The binary-weighted flow resistance has been specified by a serial or a parallel connection of an identical flow resistor to improve the linearity of the flow-rate control, thereby making the flow-resistance ratio insensitive to the size uncertainty in flow resistors due to micromachining errors. We have designed and fabricated three different types of 4-digit DMFC: Prototype S and P are composed of the serial and the parallel combinations of an identical flow resistor, while Prototype V is based on the width-varied flow resistors. In the experimental study, we perform a static test for DMFC at the forward and backward flow conditions as well as a dynamic tests at pulsating flow conditions. The fabricated DMFC shows the nonlinearity of 5.0% and the flow-rate levels of 16(2$^{N}$) for the digital control of 4(N) valves. Among the 4-digit DMFC fabricated with micromachining errors, Prototypes S and P show 27.2% and 27.6% of the flow-rate deviation measured from Prototype V, respectively; thus verifying that Prototypes S and P are less sensitive to the micromachining error than Prototype V.V.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.143-152
• /
• 2004

A novel low-power wideband bipolar second-generation current conveyors(CCIIs) and its application to universal instrumentation amplifier(UIA) were proposed. The CCII for accuracy voltage or current transfer characteristics and low current input impedance adopted adaptive current bias circuit into conventional class Ab CCII. The UIA consists of only two CCIIs and four resistors. Three instrumentation function of the UIA can be realized by selection of input signals and resistors. The simulation results show that the CCII has input impedance of 2.0$\Omega$ and the voltage gain of 60㏈ for frequency range from 0 to 50KHz when used as a voltage amplifier. The CCII has also good characteristics of current follower for current range from -100㎃ to ＋100㎃. The simulation results show that the UIA has three instrumentation amplifier functions without resistor matching. The UIA has the voltage gain of 40㏈ for frequency range from 0 to 100KHz when used as a fully-differential instrumentation amplifier. The power dissipations of the CCII and the UIA are 0.75㎽ and 1.5㎽ at supply voltage of $\pm$2.5V, respectively.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.5
• /
• pp.1-9
• /
• 1989

In binary digital transmission system the band-limiting is required for the better transmission efficiency. But in the case of band-limiting the intersymbol-interference (ISI) usually takes place. In this paper, in an attempt to design band-limiting filter which has minimum ISI and maximum stop-band loss, first, making use of analog filter by combining Binary Transversal Filter (BTF) and analog filter (4th Butterworhfilter), we found the value that minimizes ISI phenomenon by getting step response of rectangular pulse resulting from BTF in time domain. Second, we found filter characteristic we want to in frequency domain for band-limiting and minimized the error. And then we obtained resistor value (Tap coefficient) in order to design algorithm for optimum filter. Also we showed the example of simulation in case we established the resistors with 3,5 and 7 respectively. With 7 resistors set, we identified that the ripple of about minus 30dB was taken place.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.1
• /
• pp.1-5
• /
• 2000

Co-fired resistors for high frequency MCM-C (Multi Chip Module-Cofired) were fabricated and measured their RF properties from DC to 6 GHz. LTCC (Low Temperature Co-fired Ceramics) substrates with 8 layers were used as the substrates. Resisters and electrodes were printed on the 7th layer and connected to the top layer by via holes. Deviation from DC resistance of the resistors was resulted from the resister pastes, resistor size, and via length. From the experimental results, the suitable equivalent circuit model was adopted with resistor, transmission line, capacitor, and inductor. The characteristic impedance $Z_{o}$ of the transmission line from the equivalent circuit can explain the RF behavior of the buried resistor according to the structural variation.