• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.23-32
• /
• 2020

The compression sensing technology, CAFB, was developed to obtain the raw signal of the target structure by compressing it into a signal of the intended frequency range. At this point, for compression sensing, the CAFB can be optimized for various reference signals depending on the desired frequency range of the target structure. In addition, optimized CAFB should be able to efficiently compress the effective structural answers of the target structure even in sudden/dangerous conditions such as earthquakes. In this paper, the targeted frequency range for efficient structural integrity monitoring of relatively flexible structures was set below 10Hz, and the optimization method of CAFB for this purpose and the seismic response performance of CAFB in seismic conditions were evaluated experimentally. To this end, in this paper, CAFB was first optimized using Kobe seismic waveform, and embedded it in its own wireless IDAQ system. In addition, seismic response tests were conducted on two span bridges using Kobe seismic waveform. Finally, using an IDAQ system with built-in CAFB, the seismic response of the two-span bridge was wirelessly obtained, and the compression signal obtained was cross-referenced with the raw signal. From the results of the experiment, the compression signal showed excellent response performance and data compression effects in relation to the raw signal, and CAFB was able to effectively compress and sensitize the effective structural response of the structure even in seismic situations. Finally, in this paper, the optimization method of CAFB was presented to suit the intended frequency range (less than 10Hz), and CAFB proved to be an economical and efficient data compression sensing technology for instrumentation-monitoring of seismic conditions.

• Economic and Environmental Geology
• /
• v.49 no.2
• /
• pp.105-120
• /
• 2016

Most of riverside in Korea, in case of application of water curtain cultivation (WCC) technique, has been inveterately suffering from the gradual drawdown of groundwater level and related shortage of water resources during the WCC peak time. We believe that the water resources issue in these riverside areas can be effectively solved when the interaction between groundwater and nearby surface water is well understood. To investigate the connection between stream and ground water, and the influence of stream water on the nearby aquifer, this study examined the water temperature and oxygen and hydrogen stable isotopic compositions. The study area is well-known strawberry field applying the WCC technique in Sangdae-ri, Gadeok-myon, Cheongju City, and the sampling was done from February 2012 through June 2014 for stream and ground water. Some groundwater wells near stream showed big temporal variations in water temperature, and their oxygen and hydrogen stable isotopes showed similar compositions to those of adjacent stream water. This indicates that the influence of stream water is highly reflected in the stable isotopic composition of groundwater. Four cross-sectional lines from stream to hillside were established in the study area to determine the spatial differences in water quality of wells. At the late stage of WCC in February to March, groundwater of wells in line with short cross-sectional length showed the narrow range of isotopic compositions; however, those in the long cross-sectional line showed a wide compositional range. It was shown that the influence of the stream water at the late WCC stage have reached to the distance of 160 to 165 m from stream line, which is equivalent to the whole length and one-third point in each short and long cross-sectional line, respectively. Therefore, the wide compositional range in the long cross-sectional lines was not only due to the influence of stream water, but apparently resulted from the change of relative impact of each groundwater supplying from two or more aquifers. In view of stable isotopic compositions, there seems to be three different aquifers in this study area, which is competing for dominance of water quality in wells at each period of WCC.

• Journal of the Korean Vacuum Society
• /
• v.21 no.6
• /
• pp.333-341
• /
• 2012

Indium Tin Oxide (ITO) thin films were prepared by RF magnetron sputtering with different flow rates of $O_2$ gas from 0 to 12 sccm. Electrical and optical properties of these films were characterized and analyzed. ITO deposited on soda lime glass and RF power was 2 kW, frequency was 13.56 MHz, and working pressure was $1.0{\times}10^{-3}$ Torr, Ar gas was fixed at 1,000 sccm. The transmittance was measured at 300~1,100 nm ranges by using Photovoltaic analysis system. Electrical properties were measured by Hall measurement system. ITO thin films surface were measured by Scanning electron microscope. Atomic force microscope surface roughness scan for ITO thin films. ITO thin films secondary electron emission coefficient(${\gamma}$) was measured by ${\gamma}$-Focused ion beam. The resistivity is about $2.4{\times}10^{-4}{\Omega}{\cdot}cm$ and the weighted average transmittance is about 84.93% at 3 sccm oxygen flow rate. Also, we investigated Work-function of ITO thin films by using Auger neutralization mechanism according to secondary electron emission coefficient(${\gamma}$) values. We confirmed secondary electron emission peak at 3 sccm oxygen flow rate.

• Journal of fish pathology
• /
• v.18 no.3
• /
• pp.269-276
• /
• 2005

The concentrations of quinolones (oxolinic acid; OXA, norlloxacin: NRF & ciprofloxacin: CPF) after oral administration of single doses (20 mg/kg B.W.) were investigated in carp (Cyprinus carpio) kept in freshwater at 20-23$^{\circ}C$. The distribution of the drug was studied after treatment. At points timed, from 1 h to 96 hrs after administration, blood (B), liver (L), kidney (K) and muscle (M) from 5 individuals in each group were collected for analyse with microbiological bioassay method. The peak concentrations were measured at 8 h (L), 12 h (B and K) and 24 h (M) after administration regardless of treated drugs. Considerably high concentrations of CPF (13.8-19.6${\mu}g/m{\ell}$) NRF (11.8-16.9${\mu}g/m{\ell}$) and OXA (10.8-13.9 ${\mu}g/m{\ell}$) were revealed during the 24 h. At the last time point of the experiment (96 h), concentrations of all three quinolones were: OXA, 2.3-6.3 ${\mu}g/m{\ell}$ ; NRF, 3.1-4.5 ${\mu}g/m{\ell}$ ; CPF, 3.0-5.5${\mu}g/m{\ell}$ in samples. The concentrations decreased subsequently, indicating a first rapid redistribution, followed by a slow phase of elimination. The steady state was observed in blood (12-36 h), liver (12-96 h) and muscle (36-96 h) after the initiation of treatment with OXA. Concerning the compartmental concentrations, (L, K. and M/B concentration ratio), the fluctuation of the ratio was founded at different time points, among drugs. For CPF, highest tissue ratios were prolonged in the order of L>K>M (0.65-1.2/0.82-0.93/1.0-1.7) during the experiments. On the other hand, NRF presented L>K>M (0.65-1.3/0.86-1.0) till 24 h, but L>M>K (0.89-1.26) at 36-96 h. OXA showed L>K>M (0.95-2.1) at 1-8 h, M>K>L (0.51-1.0) at 12-36 hand M>L>K (1.0-2.3) at 48-96 h, respectively.

• Economic and Environmental Geology
• /
• v.49 no.4
• /
• pp.301-314
• /
• 2016

Disused Sealed Radioactive Sources (DSRSs) are stored temporally in the centralized storage facility of Korea Radioactive Waste Agency (KORAD) and planned to be disposed in the low- and intermediate-level radioactive waste (LILW) disposal facility in Gyeongju city. In this study, preliminary post-closure safety assessment was performed for DSRSs in order to draw up an optimum disposal plan. Two types of disposal options were considered, i.e. engineered vault type disposal and rock cavern type disposal which were planned to be constructed and operated respectively in LILW disposal facility in Gyeongju city. Assessment end-point was individual effective dose of critical group and calculated by using GoldSim code. In normal scenario, the maximum dose was estimated to be approximately $1{\times}10^{-7}mSv/yr$ for both disposal options. It meant that both options had sufficient safety margin when compared with regulatory limit (0.1 mSv/yr). Otherwise, in well scenario, the maximum dose exceeded regulatory limit of 1 mSv/yr in engineered vault type disposal and the exposure dose was mainly contributed by $^{226}Ra$, $^{210}Pb$ (daughter nuclide of $^{226}Ra$) and $^{237}Np$ (daughter nuclide of $^{241}Am$). For rock cavern type disposal, even though the peak dose satisfied regulatory limit, the exposure doses by $^{14}C$ and $^{237}Np$ were relatively high above 10% of regulatory limit. Therefore, it is necessary to exclude $^{14}C$, $^{226}Ra$ and $^{241}Am$ for two type of disposal options and additional management such as long-term storage and development of disposal container for those radionuclides should be performed before permanent disposal for conservative safety and security.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.3
• /
• pp.335-341
• /
• 2009

Statements of problem: Adequate bone quality and quantity were important to achieve initial stability and to prevent early failures. However there were few published data available regarding the actual effect of dimensional change in implant geometry on initial stability. Purpose: The purpose of the current study was to investigate the influence of diameter and length changes on initial stability of implants. Material and methods: Four types of dummy bone (D1, D2, D3 and D4) consisted of cortical and cancellous layers with different thickness were simulated. Implants which had similar surface area to each other ($3.5{\times}13.0-mm$, $4.0{\times}11.5-mm$, $4.5{\times}10.0-mm$, $5.0{\times}8.5-mm$) were inserted in dummy bones. Implant stability as a function of peak insertion torque and resonance frequency values were recorded for each implant. Results: 1. Bone quality was a major influential factor to achieve initial stability (P <.05). 2. In D1, D2 and D3 dummy bones, implant stability quotient values were not significantly different to each other (P >.05), however insertion torques were increased with wider and shorter implants (P <.05). 3. In D4 dummy bone, implant stability quotient values and insertion torques were decreased with wider and shorter implants (P <.05). Conclusion: From a point of view of initial stability, it is suggested that use of wide and short implant may be helpful in avoiding bone augmentation procedures in area of adequate bone quality.

• Journal of Korean Society of Forest Science
• /
• v.99 no.4
• /
• pp.559-567
• /
• 2010

This study was conducted to investigate the hydrological characteristics of groundwater level change and rainfall hydrological runoff processes caused by tunnel construction at Milbot bog located in Mt. Cheonseong. Data were collected from July 2004 to May 2008. The results were summarized as follows: The occurrence time of the direct runoff caused by unit rainfall at the Milbot bog were tended to be slower than those at general mountainous basin. Also, runoff did not sensitively respond to amount of rainfall at the most of the long and short term hydrograph. The annual runoff rates from 2004 to 2008 were 0.26, 0.13, 0.16, 0.25 and 0.27, respectively, slightly increased after 2005 regardless of the tunnel construction. Thus, the function of Milbot bog will be weakened, and it supposed to be changed to land in the future because of increasing annual runoff. The annual runoff rate for 4 years was 0.19, which is greatly lower than that of general mountainous basin. The recession coefficient of the direct runoff in short term hydrograph was ranged to 0.89~0.97, which is much larger than that of the general mountainous basin, 0.2~0.8. The recession coefficient of base flow ranged from 0.93 to 0.99, which are similar to general mountainous watershed's values. Groundwater level of Milbot bog increased or decreased in proportion to rainfall intensity, and in the descending time after the groundwater level was reached at peak point, it tends to be decreased very slowly. Also, groundwater level increased or decreased maintaining relatively high value after precedent rainfall. Groundwater level was highest during summer with heavy rainfall, but was lowest during winter. Average groundwater levels decreased annually from 2004 to 2008, -8.48 cm, -14.60 cm, -20.46 cm, -20.11 cm, -28.59 cm, respectively. Therefore, it seems that the Milbot bog is becoming dry and losing its function as a bog.

• Restorative Dentistry and Endodontics
• /
• v.32 no.1
• /
• pp.69-79
• /
• 2007

The purpose of this study was to investigate the effects of composite resin restorations on the stress distribution of notch shaped noncarious cervical lesion using three-dimensional (3D) finite element analysis (FEA). Extracted maxillary second premolar was scanned serially with Micro-CT (SkyScan1072 ; SkyScan, Aartselaar, Belgium). The 3D images were processed by 3D-DOCTOR (Able Software Co., Lexington, MA, USA). ANSYS (Swanson Analysis Systems, Inc., Houston, USA) was used to mesh and analyze 3D FE model. Notch shaped cavity was filled with hybrid or flowable resin and each restoration was simulated with adhesive layer thickness ($40{\mu}m$) A static load of 500 N was applied on a point load condition at buccal cusp (loading A) and palatal cusp (loading B). The principal stresses in the lesion apex (internal line angle of cavity) and middle vertical wall were analyzed using ANSYS. The results were as follows 1. Under loading A, compressive stress is created in the unrestored and restored cavity. Under loading B, tensile stress is created. And the peak stress concentration is seen at near mesial corner of the cavity under each load condition. 2. Compared to the unrestored cavity, the principal stresses at the cemeto-enamel junction (CEJ) and internal line angle of the cavity were more reduced in the restored cavity on both load con ditions. 3. In teeth restored with hybrid composite, the principal stresses at the CEJ and internal line angle of the cavity were more reduced than flowable resin.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.29 no.4
• /
• pp.27-39
• /
• 2011

The study on Musan twelve peaks of Yongho garden in Jinju, Gyeongnam was anticipated to provide data and implication for reproducing similar spaces and modern changes in terms of design factor since it is the prototype of traditional mount for overcoming monotonous geographical features and intriguing changes and interests. The study analyzed and interpreted the symbolism of twelve peaks, principles of space composition and function and effect of visual construction that were pursued by the builder in terms of landscape view, which results are as following. The center of Yongho garden, Yonghoji(龍虎池) is a typical man-made pond for a supportive feng shui feature. It is a supporting equipment to complete the state of feng shui, and the result of strengthening the completion through the connection with the dragon-related name of the place. The shape of Musan twelve peaks looks like an oval form of Geumseongsan(金星山), 2~3.5m in height and 6~12m in diameter. Peaks are estimated as 1.5~3.7m(2.4m in average) in height, $35{\sim}138m^2$($73.4m^2$ in average) in area, and $30.7{\sim}115.0m^3$($62.5m^3$ in average) in volume. Given that Yonghojeong(龍虎亭), Soseon(小船), the site of main building and Yongsanjae(龍山齋) stand in line, Yonghoji was presumed as the state of enlightenment through ascribing the meaning to virtue and secularity. For the intention of realizing Musan twelve peaks, the builder probably had mounted twelve peaks forming the body of dragons with crossing the point corresponding to a head of tiger, and located Musan twelve peaks and Yonghojeong with a representation of dragons holding Cintamani rising into the sky in the center. The middle area near Musan twelve peaks surrounded by peaks like Geumseongsan running north and south shows a multi-structure of multilayer, maintaining the similarity centering on Yonghoji. It is considered the intention of mount planned at the time of Musan twelve peaks construction, caused by similar form harmony. Internalization of progressive realization through concealment and exposure, enframement effect and spatial order like prospect-refuge theory in the mount of Musan twelve peaks is considered the reflection of the intention to increase depth of the view and expectancy through the various degree of exposure and surroundings of each peak and the colorful combination of viewing and shutting. The "closed view" by Musan twelve peaks creates interesting, vivid and attractive recognition of the view, which is more effective in bringing depth of the view and interests in terms of the geographical design, particularly the area around Yonghoji. Moreover, it was identified that the combination of peaks can be formed resulted from the view configuration concerning the location through multilayer effect reveals an island through the other one when viewed from Yonghojeong.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.3
• /
• pp.333-344
• /
• 2022

The quarrying and utilization of natural building stones such as granite and marble are rapidly emerging in developing countries. A huge amount of wastes is being generated during the processing, cutting and sizing of these stones to make them useable. These wastes are disposed of in the open environment and the toxic nature of these wastes negatively affects the environment and human health. The growth trend in the world stone industry was confirmed in output for 2019, increasing more than one percent and reaching a new peak of some 155 million tons, excluding quarry discards. Per-capita stone use rose to 268 square meters per thousand persons (m²/1,000 inh), from 266 the previous year and 177 in 2001. However, we have to take into consideration that the world's gross quarrying production was about 316 million tons (100%) in 2019; about 53% of that amount, however, is regarded as quarrying waste. With regards to the stone processing stage, we have noticed that the world production has reached 91.15 million tons (29%), and consequently this means that 63.35 million tons of stone-processing scraps is produced. Therefore, we can say that, on a global level, if the quantity of material extracted in the quarry is 100%, the total percentage of waste is about 71%. This raises a substantial problem from the environmental, economical and social point of view. There are essentially three ways of dealing with inorganic waste, namely, reuse, recycling, or disposal in landfills. Reuse and recycling are the preferred waste management methods that consider environmental sustainability and the opportunity to generate important economic returns. Although there are many possible applications for stone waste, they can be summarized into three main general applications, namely, fillers for binders, ceramic formulations, and environmental applications. The use of residual sludge for substrate production seems to be highly promising: the substrate can be used for quarry rehabilitation and in the rehabilitation of industrial sites. This new product (artificial soil) could be included in the list of the materials to use in addition to topsoil for civil works, railway embankments roundabouts and stone sludge wastes could be used for the neutralization of acidic soil to increase the yield. Stone waste is also possible to find several examples of studies for the recovery of mineral residues, including the extraction of metallic elements, and mineral components, the production of construction raw materials, power generation, building materials, and gas and water treatment.