• Journal of Welding and Joining
• /
• v.27 no.1
• /
• pp.85-89
• /
• 2009

Reflow process conditions were investigated for 0402 electric parts with Sn-3.0Ag-0.5Cu solders. Circle hole shape metal mask with 100 m thickness showed excellent printability. Self alignment abilities were 71% for 1005 chips, 52% for 0603 chips, and 3% for 0402 chips. Average joining strengos were 1990 gf for 1005 chips, 867 gf for 0603 chips, and 525 gf for 0402 chips. As mis-mounting angle increased, joining strength decreased. Considering self-alignment ability, mounting angle had to be under $5^{\circ}$ and contact area of the chips had to be over 40% for Pb-free soldering process for 0402 chips.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.2
• /
• pp.39-43
• /
• 2002

The eutectic solder Sn-37Pb and the lead free solder alloys with the compositions of Sn-0.7Cu, Sn-3.5Ag, Sn-3.5Ag-0.75Cu, Sn-2.0Ag-0.7Cu-3.0Bi were applied to the 48 BGA packages, and then it was discussed for the shear strength at the solder joints as the hardness and the composition of the small solder ball. As a result of experiments, the high degree of hardness with the displacement of 0.043 mm was obtained in Sn-2.0Ag-0.7Cu-3.0Bi. The shear strength of the lead free solder was higher than that of Sn-37Pb solder, and it can be obtained the maximum value of about 52% in Sn-2.0Ag-0.7Cu-3.0Bi.

• Journal of the Korean Solar Energy Society
• /
• v.38 no.1
• /
• pp.45-55
• /
• 2018

Environmentally benign lead-free solder coated ribbon (e. g. SnCu, SnZn, SnBi${\cdots}$) has been intensively studied to interconnect cells without lead mixed ribbon (e. g. SnPb) in the crystalline silicon(c-Si) photovoltaic modules. However, high melting point (> $200^{\circ}C$) of non-lead based solder provokes increased thermo-mechanical stress during its soldering process, which causes early degradation of PV module with it. Hence, we proposed low-temperature conductive paste (CP) based tabbing method for lead-free ribbon. Modules, interconnected by the lead-free solder (SnCu) employing CP approach, exhibits similar output without increased resistivity losses at initial condition, in comparison with traditional high temperature soldering method. Moreover, 400 cycles (2,000 hour) of thermal cycle test reveals that the module integrated by CP approach withstands thermo-mechanical stress. Furthermore, this approach guarantees strong mechanical adhesion (peel strength of ~ 2 N) between cell and lead-free ribbons. Therefore, the CP based tabbing process for lead free ribbons enables to interconnect cells in c-Si PV module, without deteriorating its performance.

• Journal of Welding and Joining
• /
• v.35 no.3
• /
• pp.21-27
• /
• 2017

A soldering temperature of ($235{\pm}3$) $^{\circ}C$ is described in ISO 9455-15 for the copper corrosion test. However, this temperature is not suitable for performing lead-free solder pastes. We evaluated the compatibility of a lead-free solder paste in the experimental conditions of (Liquidus temperature + ($35{\pm}3$)) $^{\circ}C$. Based on the results after a Cu corrosion test, a proper temperature for Pb-free soldering was (melting point+($35{\pm}3$)) $^{\circ}C$. Criteria used to evaluate corrosion due to discoloration of flux residue is described in ISO 9455-15, but a more quantitative evaluation standard is needed. In this study, experimental error level was estimated by analyzing flux residue after a corrosion test for 72, 500 hours of specimens using EDS analysis with acceleration voltage. It was determined that the copper area at the flux residue boundary is suitable for the EDS analysis area.

• Applied Microscopy
• /
• v.45 no.2
• /
• pp.89-94
• /
• 2015

This article briefly reviews the results of recently reported research on high-temperature Pb-free solder alloys and the research trend for characterization of the interfacial reaction layer. To improve the product reliability of high-temperature Pb-free solder alloys, thorough research is necessary not only to enhance the alloy properties but also to characterize and understand the interfacial reaction occurring during and after the bonding process. Transmission electron microscopy analysis is expected to play an important role in the development of high-temperature solders by providing accurate and reliable data with a high spatial resolution and facilitating understanding of the interfacial reaction at the solder joint.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.218-221
• /
• 2007

The surface mounting technology of 0402 electric chip part is necessary to fabricate a high density and multi-functional module, but there is a limitation of the technology, like as a bridge and self-alignement. This work estimated SMT processing factors of 0402 chip. To obtain optimum SMT process, we evaluated effects of stencil thickness, shape of hole on printability and mountability. Printability shows best results under the thickness of $80{mu}m$ with circle hole shape and 90% square hole shape. In case of chip mounting process, chip mis-alignment and bridge was occurred rarely in same conditions. In more thin stencil thickness, $50{mu}m$, strength of 1005 chip parts was poor, because of amount of printed solder was insufficient.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.2
• /
• pp.25-30
• /
• 2018

Sn-Pb solder has been used in automotive electronics for decades. However, recently, due to the environmental and health concerns, some international environmental organizations such as the end-of-life vehicle (ELV) enacted legislation banning of the Pb usage in automotive electronics. For this reason, many studies to develop and promote Pb-free soldering have been significantly reported. Meanwhile, because of flexibility and lightweight, flexible printed circuit boards (FPCBs) have been increasingly used in automotive electronics for lightweight to improve fuel efficiency and space utilization. Although the properties of lead-free solders for automotive electronics have been widely studied, there is a lack of research on the reliability performance of the lead-free solder joint on FPCB under user conditions. This study reported the properties of solder joints between Pb-free solders such as Sn3.0Ag0.5Cu, Sn0.7Cu and Sn0.5Cu0.01Al (Si), and various FPCBs finished with organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG). To evaluate on joint properties and reliabilities with different solder compositions and surface-finishing materials, pull strength test, thermal shock test, and bending cycle test were performed and analyzed. After the bending cycle test of solder joint on OSP-finishing, the fractures were occurred in solder and the lifetime of Sn3.0Ag0.5Cu solder joint was the longest.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.64-72
• /
• 2023

In this study, after transferring graphene on a Cu substrate and printing a Sn-3.0Ag-0.5Cu Pb-free solder paste on the Cu substrate, effects of the transferred graphene on formations and growths of intermetallic compound (IMC) at the interface between the Cu substrate and the solder were reported during processes of reflow soldering and isothermal aging for 1000 h with various temperatures (125, 150, and 175 ℃). Thicknesses of Cu₆Sn₅ and Cu₃Sn IMCs at the interfaces with graphene were decreased during the reflow soldering and isothermal aging processes compared to those without graphene. The transferred graphene layers also showed that the growth rate constant and square of growth rate constant which related to the growth mechanisms of Cu₆Sn₅ and Cu₃Sn IMCs with t he t emperature a nd t ime of t he i sothermal aging c ould dramatically decreased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.134-141
• /
• 2013

Reflow soldering process is essential in electronic package. Reflow process for a long time results from the decrease of reliability because IMC is formed excessively. Solder alloys of Sn-37Pb and Sn-Ag with different kinds of Cu contents (0, 0.5 and 1 wt.%) as compared with Ni and Cu plate joints are investigated according to varying reflow time. The interfaces of solder joints are observed to analyze IMC (intermetallic compound) growth rate by scanning electron microscope (SEM). Shear test is also performed by using SP (Share-Punch) tester. The test results are compared with the solder joints of two different plates (Ni and Cu plate). $Cu_6Sn_5$ IMCs are formed on Cu plate interfaces after reflows in all samples. Ni3Sn4 and $(Cu,Ni)_6Sn_5$ IMCs are also formed on Ni plate interfaces. The IMC layer forms are affected by reflow time and contents of solder alloy. These results show that mechanical strength of solder joints strongly depends on thickness and shape of IMC.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.224-227
• /
• 2003

The longitudinal thermosonic bonding method is investigated in this work for its application to the soldering process for electronic packaging. The effect of the ultrasonic is analyzed through lumped modeling, and the material properties of a viscoelastic model are measured experimentally. The thermosonic bonding method is verified by inserting the Cu pin and Au bump into solder block. As the solder thickness decreases, temperature of the solder is calculated to increase rapidly because of larger strain. Localized heating due to ultrasonic vibration is observed to melt the solder near the pin, which is adequate to the high density electronic package and Pb-free solder having high melting temperature.