• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.8-14
• /
• 2004

In this paper, We designed the electronic ballast power factor corrected(PFC) circuity for an 400[W] hight pressure soldium lamp using boost-converter. The values of PFC elements in the proposed boost-converter circuit are calculated theoretically and performed simulation using IsSPICE. We also implemented the ballast for high pressure sodium lamp and experiments. We found that the experimental characteristics of implemented PFC circuit were same with those of simulation results. The experimental results show the performance as PF 90.3[%] at output 400(W).

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1288-1297
• /
• 2016

This study proposes a single-stage light-emitting diode (LED) tube lamp driver with input-current shaping for T8/T10-type fluorescent lamp replacements. The proposed AC-DC LED driver integrates a dual-boost converter with coupled inductors and a half-bridge series-resonant converter with a bridge rectifier into a single-stage power conversion topology. This paper presents the operational principles and design considerations for one T8-type 18 W-rated LED tube lamp with line input voltages ranging from 100 V rms to 120 V rms. Experimental results for the prototype driver show that the highest power factor (PF = 0.988), lowest input current total harmonic distortion (THD = 7.22%), and highest circuit efficiency (η = 92.42%) are obtained at an input voltage of 120 V. Hence, the proposed driver is feasible for use in energy-efficient indoor lighting applications.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.5
• /
• pp.904-911
• /
• 2010

This paper presents the design of acoustic resonance free and over current limit during transient state consideration electronic ballast for 1.5kW Metal-Halide Lamp(MHL) that employs frequency modulation (FM) technique. The proposed ballast consists of a Full-Bridge(FB) rectifier, a passive power factor correction (PFC) circuit, a full-bridge inverter, an ignitor using LC resonance and a control circuit for frequency modulation. The frequency modulation technique is the most effective solution to eliminate acoustic resonance among other technique. It spreads power spectrum of lamp to reduce the supplied power spectrum under the energy level of eigen-value frequency. Moreover, the proposed ballast is simple and cost effective above conventional ballast. A new PFC circuit is proposed which combines with LCD type and PCSR filter. A new PFC circuit has higher PF and lower THD than conventional LCD type and secure high reliability. Finally, to protected switching components in transient state, the surge current into ballast is limited by increase the switching frequency. Performance of the proposed ballast was validated through computer simulation using Pspice, experimentation and by applying it to an electronic ballast for a prototype 1.5kW MHL.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.3
• /
• pp.126-134
• /
• 2018

In this research, we produced polycrystalline n-type $Bi_2Te_{2.7}Se_{0.3}$ powder using water atomization. To obtain full benefit through water atomized powder, we have implemented spark plasma sintering and hot extrusion for powder compaction. The microstructure and thermoelectric properties were investigated and compared. The average grain size of SPS and extruded bulks were 3.08 and $3.86{\mu}m$ respectively. The extruded material microstructure contains layered grains with less grain boundaries and its counter-part SPS displays dense packed grains with high grain boundaries. Among both bulks, extrusion sample exhibited high power factor (PF) of $2.96{\times}10^{-3}Wm^{-1}K^{-2}$ which is 38% higher than SPS ($2.14{\times}10^{-3}$) bulk sample. Due to variations in grain size and grain boundaries, the SPS bulk shows low thermal conductivity than extruded bulk. However, the extruded bulk sample exhibited a peak ZT of 0.69 at 400 K, which is 19% higher than SPS bulk sample, due to its higher power factor.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.10
• /
• pp.530-535
• /
• 2001

Resonant-type electronic ballast for a metal halide discharge(MHD) lamp is proposed and implemented for 400W MHD lamp. HID lamps have good color rendition, long life and good focusing capability but they have flickers by acoustic resonance when driven at high frequency. A new control method is employed to remove acoustic resonance related instability in HID lamp. By using the amplitude modulation, a spread spectrum effect is employed on the ballast. The control loop of resonant inverter is analyzed and a current is designed. The ballast consists of a power factor controller, an half-bridge resonant inverter, a simple ignitor and an integrator with OP-amps. The experimental results show the good performance as PF 0.93, ballast loss 22W at output 400W and the conducted EMI level is below 60dBuV.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.431-436
• /
• 2001

Boost converter operating at the boundary region CCM and DCM is designed. Boost converter is incorporated behind rectifier as an equivalent resistance. Also for a high efficiency and PF, a switch turn-on time is controlled by using the capacitor filter effect. To verify a validity of the designed boost converter 100[W] boost converter is fabricated and also experiment are carried out.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.159-159
• /
• 2016

세계적으로 대체 에너지는 중요한 이슈가 되고 있으며, 이들 중 열전 재료는 열 에너지를 전기 에너지로 바꿀 수 있는 열전 재료가 각광 받고 있다. 그 중, 박막 형태의 열전 재료는 벌크 형태에 비해 나노 구조화가 용이하여 열전 특성을 향상 시킬 수 있는 잠재력을 지니고 있다. 특히, 박막형 열전 소자는 정밀 온도 제어가 가능하며, 소형화 기기의 응용이 가능하여, 고 직접화 전자 소자의 발열 문제를 해결 할 수 있어 더욱 주목 받고 있다. 박막형 열전소자 중 산화물 반도체계에 대한 연구가 활발히 진행되고 있으며, 이러한 산화물 반도체는 기존의 화합물 반도체인 Pb-Te, Bi-Te 등의 기존의 재료에 비해 낮은 독성을 가진다. 또한, 고온에서 열적 안정성이 우수하여 고온에서 적용 가능하다는 장점을 가진다. 열전재료의 효율은 열전 성능 지수(ZT)와 Power factor(PF)로 평가된다.

• Journal of Industrial Technology
• /
• v.23 no.A
• /
• pp.35-39
• /
• 2003

There are many kinds of electronic ballast for various kinks of fluorescent lamps. The PFC(Power Factor Correction) circuit in electronic ballast is classified in two types. One is the active PFC and the other is the passive PFC circuit. The active type PFC is higher than the passive type, but the cost of the passive type is cheaper than the active type. In this study, we introduced the modified passive PFC method which is called semi-boost PFC, and then we analyzed and experimented the electronic ballast which is composed of the semi-boost PFC, half-bridge, and LCC resonant tank. Experimental results showed that the $$PF{\geq_-}0.98$$, $$CF{\leq_-}1.4$$ and input current $THD{\approx}15%$.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.34-39
• /
• 2004

Fluorescent lamp operated at high frequency by the electronic ballast provide ballasts like unnoticed flicker effect and higher luminous efficiency. This paper presents analysis of Half-Bridge type resonant inverter for Fluorescent lamp drive for stable characteristic and life improvement of lamp operated at high frequency. Also, it has described an electronic ballast design with the capability of high PF (Power Factor) and low THD (Total Harmonic Distortion). The validity of designed electronic ballast circuit is confirmed by simulation and experimental results. The Designed electronic ballast is implemented successfully on 32W Fluorescent lamp system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.491-499
• /
• 2019

Recently, there has been increasing demand for power quality in power supply devices. The IEC 61000-3-2 standard requires that the AC / DC power supply for lighting meet the specifications for the power factor (PF) and total waveform distortion (THD). In addition, advanced countries in Europe are regulating the ripple rate as 15 ~ 30% for the flicker phenomenon caused by the change in the amount of foot energy due to the change in current of the output terminal. Therefore, domestic standards and regulations are being updated. This study adopted the Flyback converter to satisfy the PFC standard, and has the circuit first and second insulation function. To reduce the low frequency ripple of the LED current, Flyback, Coupled Inductor, LC parallel resonance filter, LLC resonance filter, and Cuk were simulated by PSIM to mimic each LED driving circuit. A coupled LC resonant circuit with a coupled inductor on the primary side and LC resonance on the secondary side was also proposed for output side ripple reduction.