• Journal of Welding and Joining
• /
• 제4권2호
• /
• pp.21-29
• /
• 1986

The influence of welding heat input variation(600-900J/cm) and heat-treatment condition after welding on tensile strength of butt welded joint in $175Kg/mm^2$ strength level Maraging steel(Co-free and Co-containing) sheets was investigated on the basis of hardness distribution, microstructure of weld metal and fracture surface. The obtained main results are as follows; 1. The strength of weldment (UTS, NTS), joint efficiency showed a little decreasing tendency with the increase in welding heat input, and the elongation showed a little increasing tendency with the increase in the width of weld metal. It was considered because of the plastic constraint of the high strength base metal. 2. The strength of weldment was better in the solution treatment and aging than the aging only after welding due to the disappearance of almost denverite in weld metal. 3. The hardness distribution in weldment after welding and heat-treatment was almost similar to both Co containing and Co free Maraging steel with change in welding heat input. 4. The fracture was occurred at weld metal, and the fracture surface showed a relatively shallow dimples in both Co containing and Co free Maraging steel.

• 소성∙가공
• /
• 제19권8호
• /
• pp.517-522
• /
• 2010

Selective laser melting (SLM) is emerged as a new manufacturing technique to directly fabricate precise parts using metallic materials. The final characteristics of a component fabricated through the SLM process are strongly dependent upon various parameters such as laser power, scan rate and pulse duration, etc. This paper, therefore, focuses on the dimensional characteristics of melted $20{\mu}m$ Fe-Cr-Ni powder by fiber laser for the selective laser melting process. With energy density decrease, the height and depth were decreased. Although the conditions are of the same energy density, the shape is different by laser power and scan rate. The shapes at various laser parameters were divided into 3 groups based on depth over height. The smooth regular shape is obtained under the conditions of $50{\mu}m$ of powder height and $15-20{\mu}s$ of pulse duration. And the laser power influenced the variation of shape more significantly than the scan rate.

• Composites Research
• /
• 제16권5호
• /
• pp.39-44
• /
• 2003

복합재료에 삽입된 점탄성 재료는 복합재구조물의 감쇠물성을 크게 증가시킨다. 일반적으로 점탄성 재료는 등방성이므로 모든 방향의 감쇠물성이 동일하다. 최근 재료의 방향에 따라 감쇠물성이 변하는 이방성 감쇠재료의 개발이 요구되고 있다. 이방성 감쇠재료는 점탄성 재료 내부에 얇은 섬유를 삽입하여 제작한다. 삽입된 섬유는 댐핑재료의 강성에 큰 영향을 주며 강성은 고전 적층판 이론을 따르게 된다. 본 논문에서는 Ni와 Adams의 이론을 이용하여 손실계수를 평가하였다. 그리고 방향성 있는 감쇠재료의 영향을 평가하기 위해 저속충격 거동해석을 수행하였다. 해석결과로부터 방향성 있는 감쇠재료는 복합적층판의 진동 및 감쇠특성에 큰 영향을 줌을 보였다

• 한국세라믹학회지
• /
• 제31권3호
• /
• pp.321-329
• /
• 1994

Functionally gradient materials(FGM), which have the continuous or stepwise variation in a composition and microstructure, are being noticed as the material that solves problems caused by heterogeneous interface of coating or joining. And these materials also expect new functions occured by gradient composition itself. Therefore, to examine possibility of thermal barrier materials, TZP/Mo·FGM and TZP/Ni·FGM were fabricated by sintering method. As to the sintered specimens, sintering shrinkage, relative density and Vicker's hardness in each composition were examined. The phenomena due to the difference of sintering shrinkage velocity during sintering process and the thermal stress induced through differences of thermal expansion coefficient in FGM were discussed. And the structure changes at interface and microsturcture of FGM were investigated. As a results, the difference of shrinkage between ceramic and metal was about 14% in TZP/Mo and 7% in TZP/Ni. The relative density and hardness were considerably influenced by metal content changes. Owing to unbalance of sintering shrinkage velocity between ceramic and metal, various sintering defects were occured. To control these sintering defects and thermal stress, gradient composition of FGM should be narrow. The microstructure changes of FGM depended on the ceramic or metal volume percents and were analogous to the theoretical design.

• Journal of Magnetics
• /
• 제18권4호
• /
• pp.391-394
• /
• 2013

In this study, nickel-zinc ferrite nanoparticles, with the chemical formula of $Ni_{0.3}Zn_{0.7-x}Cu_xFe_2O_4$ (where x = 0.1- 0.6 by step 0.1), were fabricated by the sol-gel method. The effect of copper substitution on the phase formation and crystal structure of the sample was investigated by X-ray diffraction (XRD), thermo-gravimetry (TG), differential thermal analysis (DTA), Fourier transform infrared spectrometry (FT-IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The XRD result shows that due to the reduction of Zn content,the crystallite size of the sample increased. The results of the vibration sample magnetometer (VSM) exhibit an increase in saturation magnetization value (Ms) for samples with x ${\leq}$ 0.3 and a linear decrease for samples with x > 0.3. The variation of saturation magnetization and coercivity of the samples were then studied.

• Journal of Magnetics
• /
• 제8권1호
• /
• pp.32-35
• /
• 2003

Magnetic funnel Junctions (MTJs) were fabricated on thermally oxidized Si (100) wafers using DC magnetron sputtering. The film Structures were Ta(50 ${\AA}$)/CU(100 ${\AA}$)$Ni_{80}Fe_{20}(20 $ ${\AA}$)/Cu(50 ${\AA}$)/$Mn_{75}Ir_{25}(100 $ ${\AA}$)/$Co_{70}Fe_{30}(25$ ${\AA}$)/Al-O(15 ${\AA}$)/$Co_{70}Fe_{30}(25 $ ${\AA}$)/$Ni_{80}Fe_{20}(t)/Ta(50 $ ${\AA}$), with t=0 ${\AA}$, 100 and 1000 ${\AA}$, respectively. X-ray diffraction has shown improvement of (111) texture of IrMn$_3$ and Cu by annealing. The exchange-biased energy is almost inversely proportional to temperature. The difference between the coercivity H$_c$ and the exchange biased field H$_E$ for t = 0 $_3$ sample is smaller than that for t = 1000 ${\AA}$. For the pinned layer, the decreasing rate of the coercivity with the temperature is higher compared to that of the exchange field, but variation of H$_c$ is similar to that of the exchange field for free layer.

• 한국표면공학회지
• /
• 제31권2호
• /
• pp.81-90
• /
• 1998

NiCrAly/YSZ(8wt% Y2O3-Zro2) functionally fraded thermal barrier coating (FGC) layers on a Co-base sureralloy (HAYNESS 188) substrate were fabricated using Ar shielded single torch air plasma spraying method. Functional grading were produced with the stepwise compositional change throughout layer thinkness. Microstructural observation revealed a sucessful fabrication of NiCrAly/YSZ FGC. From the results of the curvature measurement, adhesive stength measurement and thermal shock test for the FGC, it was concluded that the optimum enhance of functionally graded coating layer thinkcess and compositional pattern exit to enhance the properties of FGC, which is closely reated to the internal residual distribution with it.

• 한국주조공학회지
• /
• 제35권6호
• /
• pp.170-177
• /
• 2015

Segregation during solidification and homogenization during thermal exposure in GTD 111 were investigated. The microstructures of as-cast, standard heat-treated, and thermally exposed specimens were observed by SEM. A compositional analysis of each specimen was conducted by EDS. The dendrite core was enriched in W and Co, though lower levels of Ti and Ta were observed. An unexpected phase, in this case like the ${\eta}$ phase, was observed due to segregation near the ${\gamma}-{\gamma}^{\prime}$ eutectic in the standard heat-treated specimen. Segregation also induced microstructural evolution near the ${\gamma}-{\gamma}^{\prime}$ eutectic during the standard heat treatment. A quantitative analysis and microstructural observations showed that the thermal exposure at a high temperature enhanced the chemical homogeneity of the alloy.

• 대한기계학회논문집A
• /
• 제31권4호
• /
• pp.525-531
• /
• 2007

The operating temperature has been increased to improve the efficiency of gas turbine. The most advanced Gas turbine is operated at above $1,500^{\circ}C$. Improvement in material and cooling method permit hot gas path component to run at increased temperature. But, the repair of blades which are developed with advanced manufacture technique is difficult to use normal welding. Most of gas turbine blades are made of precipitation harden nickel base superalloy, which is very hard to weld. Therefore, the employment of welding filler on blade is solid solution nickel base superalloy(Hastelloy X, Inconel 617). In this study, Tensile test in high temperature was conducted on welded GTD111DS with GTD111 to evaluate effect of variation of pre, post treatment. The result of this study showed that the specimen was treated with optimum pre and post treatment(preweld HT($1200^{\circ}C$), Post treatment($1100^{\circ}C$ HIP, $1200^{\circ}C$ + $1100^{\circ}C$ + $800^{\circ}C$ HT) is mush superior.

• 한국자기학회지
• /
• 제9권5호
• /
• pp.245-250
• /
• 1999

기판/Py/Al2O3/Co(Py=Ni81Fe19) 터널접합의 TMR(Tunneling Magnetoresistance)에 미치는 기판과 부도체층의 효과를 보기위해 산화시간을 변화시키고 기판의 종류를 변화시켜며 전기적 특성을 측정하였다. 시료는 진공중에서 in-situ로 새도우마스크를 교환하며 제작하였다. 산화시간의 증가에 따라 터널접합의 저항은 증가하였으며 측정된 MR 값은 감소하였다. 터널 비저항이 0.17 M$\Omega$($\mu\textrm{m}$)2이하인 경우 MR이 관측되었다. 기판의 종류에 따른 MR 값은 열산화시킨 Si(111), Si(100), Cornng Glass 2948, Corning Glass 7059 순으로 감소하였다. MR 값의 부호와 변화를 불균일 전류의 흐름으로 설명하였다.