• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.2
• /
• pp.87-97
• /
• 2013

Negative bias temperature instability (NBTI) and positive bias temperature instability (PBTI) are critical circuit reliability issues in highly scaled CMOS technologies. In this paper, we analyze the impacts of NBTI and PBTI on SRAM $V_{MIN}$, and present a design solution for mitigating the impact of NBTI and PBTI on SRAM $V_{MIN}$. Two different types of SRAM $V_{MIN}$ (SNM-limited $V_{MIN}$ and time-limited $V_{MIN}$) are explained. Simulation results show that SNM-limited $V_{MIN}$ is more sensitive to NBTI while time-limited $V_{MIN}$ is more prone to suffer from PBTI effect. The proposed NBTI/PBTI-aware control of wordline pulse width and woldline voltage improves cell stability, and mitigates the $V_{MIN}$ degradation induced by NBTI/PBTI.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.10
• /
• pp.883-890
• /
• 2005

In this paper, the established model of NBTI (Negative Bias Temperature Instability) mechanism was reviewed. Based on this mechanism, then, the influence of nitrogen was discussed among other processes. A constant concentration of nitrogen exists inside $SiO_2$ in order to prevent boron from diffusing and to increase dielectric constant. It was shown that NBTI improvement was achieved by controlling nitrogen profile. It was supposed that the existence of low activation energy of Si-N bonds at $Si-SiO_2$ interface attributes the improvement by making hydrogen prevent interface traps. It was also shown that improvement of NBTI can be achieved by more effective control of nitrogen profile. It was supposed that the maximum control of nitrogen profile can be achieved by DPN (Decoupled Plasma Nitridation) process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.3
• /
• pp.181-185
• /
• 2003

Influence of post gate oxidation anneal on Negative Bias Temperature Instability (NBTI) of PMOSFE has been investigated. At oxidation anneal temperature raised above 950$^{\circ}$C, a significant improvement of NBTI was observed which enables to reduce PMO V$\_$th/ shift occurred during a Bias Temperature (BT) stress. The high temperature anneal appears to suppress charge generations inside the gate oxide and near the silicon oxide interface during the BT stress. By measuring band-to-band tunneling currents and subthreshold slopes, reduction of oxide trapped charges and interface states at the high temperature oxidation anneal was confirmed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1075-1078
• /
• 2007

Negative Bias Temperature Instability (NBTI) in Eximer Laser Annealing (ELA) based Low Temperature polysilicon (LTPS) Thin-Film Transistors (TFT) was investigated. Even though NBTI is generally appeared in devices with thin gate oxide, the TFT with gate oxide thickness of 120 nm, relatively thick, also showed NBTI effect and dynamic NBTI effect is dependent on operational frequency.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.550-552
• /
• 2009

The negative bias temperature instability on LTPS TFTs in a darkened and an illuminated environment was investigated. Experimental results reveal that the generation of interface state density showed no change between the different NBTI stresses. The degradation of the grain boundary trap under illumination was more significant than for the darkened environment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.687-694
• /
• 2008

This paper is focused on the improvement of MOS device reliability related to deuterium process. The injection of deuterium into the gate oxide film was achieved through two kind of method, high-pressure annealing and low-energy implantation at the back-end of line, for the purpose of the passivation of dangling bonds at $SiO_2/Si$ interface. Experimental results are presented for the degradation of 3-nm-thick gate oxide ($SiO_2$) under both negative-bias temperature instability (NBTI) and hot-carrier injection (HCI) stresses using P and NMOSFETs. Annealing process was rather difficult to control the concentration of deuterium. Because when the concentration of deuterium is redundant in gate oxide excess traps are generated and degrades the performance, we found annealing process did not show the improved characteristics in device reliability, compared to conventional process. However, deuterium ion implantation at the back-end process was effective method for the fabrication of the deuterated gate oxide. Device parameter variations under the electrical stresses depend on the deuterium concentration and are improved by low-energy deuterium implantation, compared to conventional process. Our result suggests the novel method to incorporate deuterium in the MOS structure for the reliability.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.2
• /
• pp.139-144
• /
• 2013

Negative bias temperature instability (NBTI) has become a major factor determining circuit reliability. The effect of the NBTI on the circuit performance depends on the duty cycle which represents the stress and recovery conditions of each device in a circuit. In this paper, we propose an analytical model to perform more accurate duty cycle estimation at the gate-level. The proposed model allows accurate (average error rate: 3%) computation of the duty cycle without the need for expensive transistor-level simulations Furthermore, our model estimates the waveforms at each node, allowing various aging effects to be applied for a reliable gate-level circuit aging analysis framework.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.2
• /
• pp.348-354
• /
• 2009

It has analyzed that the device degradation by NBTI (Negative Bias Temperature Instability) stress induced the increase of gate-induced-drain-leakage(GIDL) current for p-MOSFETs. It is shown that the degradation magnitude, as well as its time, temperature, and field dependence, is govern by interface traps density at the silicon/oxide interface. from the relation between the variation of threshold voltage and subthreshold slope, it has been found that the dominant mechanism for device degradation is the interface state generation. From the GIDL measurement results, we confined that the EHP generation in interface state due to NBTI stress led to the increase of GIDL current. Therefore, one should take care of the increased GIDL current after NBTI stress in the ultra-thin gate oxide device. Also, the simultaneous consideration of reliability characteristics and dc device performance is highly necessary in the stress engineering of nanoscale CMOSFETs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.2
• /
• pp.23-30
• /
• 2012

This paper proposes a novel adaptive header-based power gating structure to compensate for the performance loss and the increased wake-up time of the power gating structures induced by the negative bias temperature instability (NBTI) effect. The proposed structure consists of variable width footers based on the two-pass power gating and a new NBTI sensing circuit for an adaptive control. The simulation results of the proposed structure are compared to those of power gating without the adaptive control and show that both the circuit-delay and wake-up time dependence of the power gating structure on the NBTI stress is minimized with only 3% and 4% increase, respectively while keeping small leakage power and rush-current. In this paper, a 45 nm CMOS technology and predictive NBTI model have been used to implement the proposed circuits.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1A
• /
• pp.80-86
• /
• 2010

This work has been measured and analyzed the device degradation of NBTI (Negative Bias Temperature Instability) stress induced the increase of gate-induced-drain-leakage(GIDL) current for p-MOS transistors of gate channel length 0.13 [${\mu}m$]. From the relation between the variation of threshold voltage and subthreshold slop by NBTI stress, it has been found that the dominant mechanism for device degradation is the interface state generation. From the GIDL measurement results, we confined that the EHP generation in interface state due to NBTI stress led to the increase of GIDL current. As a results, one should take care of the increased GIDL current after NBTI stress in the ultra-thin gate oxide device. Also, the simultaneous consideration of reliability characteristics and dc device performance is highly necessary in the stress parameters of nanoscale CMOS communication circuit design.