• 열처리공학회지
• /
• 제12권3호
• /
• pp.215-220
• /
• 1999

Rotary bending fatigue tests were carried out to investigate the artificial defect sensitivity of fatigue limit in annealed and austempered ductile irons. Artificial defect(hole, diameter${\leq}0.4mm$) machined on specimen surface did not bring about an obvious reduction of fatigue limit in austempered ductile iron as compared with annealed. As a result of investigation on $\sqrt{area}$ c which is the critical artificial defect size. $\sqrt{area}$ c of austempered ductile iron is larger than that of annealed. This means that the crack initiation at artificial defect in austempered ductile iron is more difficult in comparison with annealed. In case that the $\sqrt{area}$ c of artificial defect and graphite nodule are same, the rate of crack initiation for graphite nodule is higher than that of artificial defect.

• International Journal of Automotive Technology
• /
• 제7권6호
• /
• pp.703-714
• /
• 2006

The growing concern surrounding rollover incidences and consequences of Sports Utility Vehicles(SUV) have prompted to investigate the sensitivity of critical vehicle parameters on rollover. In this paper, dynamic rollover simulation of Sports Utility Vehicles is carried out using a validated nonlinear vehicle model in Matlab/Simulink. A standard model is considered and critical vehicle parameters like CG height, track width and wheel base are varied within chosen specified limits to study its influence on roll behavior during a Fishhook steering maneuver. A roll stability criterion based on Two Wheel Lift Off(TWLO) phenomenon is adopted for rollover propensity prediction. Further dynamic rollover characteristics of the vehicle are correlated with Static Stability Factor(SSF), Roll Stability Factor(RSF) and Two Wheel Lift Off Velocity(TWLV). These findings will be of immense help to SUV chassis designers to determine safety limits of critical vehicle parameters and minimize rollover incidences.

• Structural Engineering and Mechanics
• /
• 제41권4호
• /
• pp.539-558
• /
• 2012

The diagnosis of bridge serviceability is carried out by a combination of in-situ visual inspection, static and dynamic loading tests and analyses. Structural health monitoring (SHM) using information technology and sensors is increasingly being used for providing a better estimate of structural performance characteristics rather than above traditional methods. Because the mechanical behavior of bridges with various kinds of damage can not be made clear, it is very difficult to estimate both the damage mode and degree of damage of existing bridges. In this paper, the sensitivity of both static and dynamic behaviors of bridges are studied as a measure of damage assessment through experiments on model bridges induced with some specified artificial damages. And, a method of damage assessment of bridges based on those behaviors is discussed in detail. Finally, based on the results, a possible application for structural health monitoring systems for existing bridges is also discussed.

• Nuclear Engineering and Technology
• /
• 제33권6호
• /
• pp.605-618
• /
• 2001

For the mechanical stability assessment of a deep underground high-level waste repository. computer simulations using FLAC3D were carried out and important parameters including stress ratio, depth, tunnel size, joint spacing, and joint properties were chosen from sensitivity analysis. The main effect as well as the interaction effect between the important parameters could be investigated effectively using fractional factorial design . In order to analyze the stability of the disposal tunnel and deposition hole in a discontinuous rock mass, different modelings were performed under different conditions using 3DEC and the influence of joint distribution and properties, rock properties and stress ratio could be determined. From the three dimensional modelings, it was concluded that the conceptual repository design was mechanically stable even in a discontinuous rock mass.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2655-2663
• /
• 1993

In order to evaluate the relative significance of tolerance management of various elements in a VHS VTR tape transport system, the effect of geometric variations of the elements from standard design values on the tape traveling path is studied. The tape is modeled as a string and each element in the tape transport system is modeled as a cylinder whose radius, position vector and orientation vector are specified. An numerical algorithm is proposed to find the coordinates of tape entry points and tape exit points for the elements from which the tape traveling path can be completely described. By using the suggested algorithm, an error sensitivity analysis of tape traveling path due to the geometric variations of tape transport elements is performed for a particular model in the market and the elements demanding relatively strict tolerance management are identified.

• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.739-744
• /
• 2002

This study predicts the modified structural eigenvectors and eigenvalues due to the change in the mass and stiffness of a structure by iterative calculation of the sensitivity coefficient using the original dynamic characteristics. The method is applied to examples of a cantilever and 3 degree of freedom lumped mass model by modifing the mass and stillness. The predicted dynamic characteristics are in good agreement with these from the structural reanalysis using the modified mass and stiffness.

• 드라이브 ㆍ 컨트롤
• /
• 제17권4호
• /
• pp.38-45
• /
• 2020

The purpose of this study was to analyze the design sensitivity of an independent driving system for disaster response. The research procedure was as follows. First, an analysis model based on the circuit diagram of the driving system was developed. Second, to ensure the reliability of the analytical model, the load-free test results and analysis results were compared. Even if different loads acted on four independent motors, the system was confirmed to be implemented according to the design intent. Finally, the design variables of the analysis model were analyzed to obtain design variables with a significant impact on system performance and stability. The analysis program used simulation X.

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.2099-2106
• /
• 2003

In this paper, a novel fast response NDIR analyzer (FRNDIR), which uses an electrically pulsed semiconductor emitter and dual type PbSe detector for the PPM-level detection of carbon dioxide (CO$_2$) at a wavelength of 4.28 $\mu\textrm{m}$, is described. Modulation of conventional NDIR energy typically occurs at 1 to 20 Hz. To achieve real time high-speed measurement, the new analyzer employs a semiconductor light emitter that can be modulated by electrical chopping. Updated measurements are obtained every one millisecond. The detector has two independent lead selenide (PbSe) with IR band pass filters. Both the emitter accuracy and the detector sensitivity are increased by thermoelectric cooling of up to -20 degrees C in all semiconductor devices. Here we report the use of semiconductor devices to achieve improved performance such that these devices have potential application to CO$_2$ gas measurement and, in particular, the measurement of fast response CO$_2$ concentration at millisecond level.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.398-401
• /
• 2001

There are two methods to calculate design sensitivity such as direct differentiation method and adjoint method. A sort of direct differentiation method for design sensitivity analysis costs too much when number of design variables is much larger than the number of response functions whose design sensitivity analyses are required. Therefore, an adjoint method is suggested for the case that the dimension of design variables is lager than the number of response function. An adjoint method is required to compute adjoint variables from the simultaneous linear system equation, the so-called adjoint equation, requiring only the eigenvalue and its associated eigenvectors for mode being differentiated. This method has been extended to the repeated eigenvalue problem. In this paper, we propose an adjoint method for deign sensitivity analysis of damped vibratory systems with distinct eigenvalues.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.746-752
• /
• 2001

Design sensitivity analysis for nonlinear structural problems has been emerged in the last decade as a glowing area of engineering research. As a result, theoretical formulations and computational algorithms have already developed for design sensitivity of nonlinear structural problems. There is not enough research for practical nonlinear problems using multi-element, due to difficulties of implementation into FEA. Therefore, nonlinear response analysis for stiffened shell which consists of Mindlin plate and Timoshenko beam, was considered. Specially, it presents the backward-Euler method which is adopted to describe an exact yield state in the stress computation procedure. Then, design sensitivity analysis of nonlinear structures, particularly elasto-perfectly-plastic structure, is developed using direct differentiation method. The accuracy of the developed sensitivity analysis was compared with the central finite difference method. Finally, on the basis of above results, design improvement for stiffened shell is suggested.