• Journal of Sensor Science and Technology
• /
• v.11 no.1
• /
• pp.54-59
• /
• 2002

This paper describes a new process technique for batch process of SOI(Si-on-Insulator) structures with buried cavities for MEMS(Micro Electro Mechanical System) applications by SDB(Si-wafer Direct Bonding) technology and electrochemical etch-stop. A low-cost electrochemical etch-stop method is used to control accurately the thickness of SOI. The cavities were made on the upper handling wafer by Si anisotropic etching. Two wafers are bonded with an intermediate insulating oxide layer. After high-temperature annealing($1000^{\circ}C$, 60 min), the SDB SOI structure with buried cavities was thinned by electrochemical etch-stop. The surface of the fabricated SDB SOI structure have more roughness that of lapping and polishing by mechanical method. This SDB SOI structure with buried cavities will provide a powerful and versatile substrate for novel microsensors arid microactuators.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.387-390
• /
• 2009

This study was designed to fabricate the micro-electro-mechanical systems (MEMS) parts such as micro spur gears using hot extrusion of gas atomized Al-78Zn powders. For this purpose, it is important to develop new methods to fabricate micro-dies and choose suitable extrusion conditions for a micro-forming. Micro-dies with Ni were fabricated by LIGA technology. LIGA technology was capable to produce micro-extrusion dies with close tolerances, thick bearing length and adequate surface quality. Superplastic Al-78Zn powders have the great advantage in achieving deformation under low stresses and exhibiting good micro formability with average strain rates ranging from $10^{-3}$ to $10^{-2}\;s^{-1}$ and constant temperatures ranging from 503 to 563K. Al-78Zn powders were compacted into a cylindrical shape (${\Phi}3{\times}h10$) under compressive force of 10kN and, subsequently, the compacted powders were extruded at 563k in a hot furnace. Micro-extrusion has succeeded in forming micro-gear shafts.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1326-1331
• /
• 2003

Thick PZT films are required for the cases of micro actuators and sensors with high driving force, high breakdown voltage and high sensitivity, and so on. In this work, thick PZT films were fabricated by Sol-Gel multi-coating method. Total 8 types of samples using thick PZT films with thicknesses, about $1{\mu}m$ and $2{\mu}m$, and Pt top electrodes shapes for measuring transverse piezoelectric coefficient ($e_{31,f}$) were fabricated using MEMS processes. They were characterized by fabricated e31,f measurement system before and after poling. $e_{31,f}$ values of samples after poling were higher than before poling. Those of $2{\mu}m$ thick PZT films were also higher than $1{\mu}m$ thick PZT films. And those with long electrodes as top electrodes were also higher than shorter.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.137-144
• /
• 2023

Micro electro mechanical systems (MEMS) and precision machines require excellent friction and wear characteristics to improve energy efficiency generated during sliding motion. In this study, DLC thin film with high hardness and low friction was deposited on STS304 substrate material by CVD method, and dot-shaped convex and concave micropatterns were fabricated by photolithography process. The diameter of the pattern was 20 ㎛, the pitch was 40 ㎛, and a pattern having a mesh type arrangement was fabricated and an abrasion test was performed. The results of the wear test on the micro pattern confirmed that the friction coefficient characteristics were improved compared to STS 304 and DLC thin films. In addition, in this result, the micro-pattern showed 11.4% more improved friction coefficient than the DLC thin film. The friction coefficient characteristics for convex and concave patterns of the same size showed almost similar results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.1015-1020
• /
• 2011

Nanoimprint lithography has been actively investigated. This method can replicate a nanopatterned master stamp onto a thin polymer film on a silicon substrate and so on. In this study, a square-shaped hollow piezoelectric actuator is presented, which is newly developed. This actuator is used for driving a nanoscale stamp in nanoimprint lithography instead of a conventional electric motor. The fabricated prototype actuator has 95 layers and side lengths of 23 mm and 18 mm for the outer and inner squares, respectively. By adopting a novel process instead of the conventional forming process for fabricating a one-layer actuator, the one-layer is composed of four rectangular segments produced by sawing a ceramic film with a thickness of 0.3 mm. The basic characteristics on displacement and generation force of the fabricated prototype actuator are experimentally investigated. Furthermore, the displacement characteristics obtained by using a PI controller are tested and discussed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1721-1725
• /
• 2010

This paper reports the fabrication of geometry-controlled carbon microneedles by a backside exposure method and pyrolysis. The SU-8 microneedles are a polymer precursor in a carbonization process, which geometries such as base diameter, spacing, and aspect ratio can be controlled in a photolithography step. Using this fabrication method, highly reproducible carbon microneedles, which have high aspect ratios of more than 10 and very sharp nanotips, can be realized. The quartz surface with carbon microneedles becomes very hydrophilic and its wettability is adjusted by carrying out the silane treatment. In the carbon microneedle array ($3\;{\mu}m{\times}3\;{\mu}m$), the contact angle is extremly enhanced (${\sim}180^{\circ}$); this will be advantageous in developing low-drag microfluidics and labs-on-a-chip as well as in other bio-applications.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.186-193
• /
• 2009

In this paper, we adopted E-MOLD patent technology in order to fabricate Prismless LGP(Light Guide Panel) fur cellular phone and estimate the transcription of injection-molded parts. Then, we manufactured the Ni stamper fur Prismless LGP using MEMS process. And the stamper was installed in the movable heated core which is the key part of a patented mold. Using this mold, we manufactured injection-molded plastic LGP parts with different mold temperatures so that we investigate effect of the temperature on the transcription of the parts. The CAE analysis was also conducted in order to compare with the experimental results. The transcription of LGP parts with various mold temperature displayed $100^{\circ}C$(25.0nm), $140^{\circ}C$(48.4nm), $180^{\circ}C$(52.1nm) and when compared with stamper(521Inm), transcription was superior at $180^{\circ}C$. According to the CAE results, moldability was improved as mold temperature ($50^{\circ}C{\sim}180^{\circ}C$) increased, but when filling time($1{\sim}2sec$) increases, it decreased at $160^{\circ}C$. And transcription and moldability were improved markedly at glass transition temperature($140^{\circ}C$).

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.49-49
• /
• 1999

리튬 이차 전지를 박막화함으로써 개발된 고상의 마이크로 박막전지는 임의의 크기 및 형태로의 제작이 가능하며 액체전해질을 사용하지 않기 때문에 작동 중 열 또는 기체 생성물이 생기지 않아 높은 안정성을 갖으며 광범위한 사용 온도 범위를 가진다. 위와 같은 장점으로 인하여 충전 가능한 고상의 박막형 리튬 이차 전지는 점진적으로 그 사용 범위가 크게 확대될 것으로 판단된다. 즉, 초소형 전자, 전기 소자는 물론이며 조만간 실현될 스마트 카드, 셀루러폰 및 PCS와 같은 개인용 휴대 통신장비의 전력 공급계로의 응용이 가능할 것이다. 특히 장수명, 고에너지 밀도를 갖는 초소형의 전지를 필요로 하는 microelectronics, MEMS등에 이용될 수 있는 이차전지에 대한 요구가 점점 가시화 됨에 따라 박막공정을 이용한 이차전지개발기술이 요구되고 있으며, 박막제조기술을 이용한 고상의 박막형 및 전지에 관한 연구가 증가하고 있다. 본 연구에서는 박막형 리튬 이차전지의 Cathode 물질로써 비정질의 산화바나듐 박막을 반응성 스퍼터링에 의하여 상온에서 증착하였다. 박막형 이차전지의 여러 가지 Cathode 물질중 산화바나듐은 다른 물질들과는 달리 비정질 형태로 매우 우수한 충방전 특성을 나타낸다. 이런 특성으로 인해 다소 전지자체의 성능은 낮지만 저전력 저전압을 필요로 하는 초소형 전자 소자와 혼성되어 이용할 수 있는 잠재성이 매우 높은 물질이다. 바나듐 타겟의 경우 타겟 표면의 ageing에 따라 증착되는 박막의 특성이 매우 달라지게 되므로 presputtering의 시간을 변화시키면서 실험하였다. 또한 스퍼터링 중의 산소의 분압도 타겟의 ageing에 많은 영향을 주므로 실험 변수로 산소분압을 변화시키면서 실험하였다. 증착된 산화바나듐 박막의 표면은 scanning electron microscopy로 분석하였으며 구조 분석은 X-선 회절분석, X-ray photoelectron spectroscopy 그리고Auger electron spectroscope로 하였다. 증착된 산화바나듐 박막의 전기화학적 특성을 분석하기 위하여 리튬 메탈을 anode로 하고 EC:DMC=1:1, 1M LiPF6 액체 전해질을 사용한 Half-Cell를 구성하여 200회 이상의 정전류 충 방전 시험을 행하였다. Half-Cell test 결과 박막의 결정성과 표면상태에 따라 매우 다른 전지 특성을 나타내었다.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.85-91
• /
• 2009

There has been a rapid progress for flexible polymer-based MEMS(Microelectromechanical Systems) technology. Polycarbonate (PC) and Poly Methyl Methacrylate (PMMA), so-called acrylic, have many advantages for optical, non-toxic and micro-device application. We studied dry etching of PC and PMMA as a function of % gas ratio in the $O_2/SF_6/CH_4$ temary plasma. A photoresist pattern was defined on the polymer samples with a mask using a conventional lithography. Plasma etching was done at 100 W RIE chuck power and 10 sccm total gas flow rate. The etch rates of PMMA were typically 2 times higher than those of PC in the whole experimental range. The result would be related to higher melting point of PC compared to that of PMMA. The highest etch rates of PMMA and PC were found in the $O_2/SF_6$ discharges among $O_2/SF_6$, $O_2/CH_4$ and $SF_6/CH_4$ and $O_2/SF_6/CH_4$ plasma composition (PC: ${\sim}350\;nm/min$ at 5 sccm $O_2/5$ sccm $SF_6$, PMMA: ${\sim}570\;nm/min$ at 2.5 sccm $O_2/7.5$ sccm $SF_6$). PC has smoother surface morphology than PMMA after etching in the $O_2/SF_6/CH_4$ discharges. The surface roughness of PC was in the range of 1.9$\sim$3.88 nm. However, that of PMMA was 17.3$\sim$26.1 nm.