• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.497-497
• /
• 2012

산업의 발전함에 따라 고기능성 박막의 수요가 증가하고 있으며, magnetron sputtering, e-beam evaporation, ion beam 등을 이용한 박막 증착에 대한 연구가 많이 진행되고 있다. 그러나 기존 방법만으로는 박막 접착계면의 불균일로 인해 고기능성 박막 성장이 어렵다는 단점을 가지고 있다. 이러한 문제를 해결하기 위하여 박막 공정 중 고밀도 플라즈마 소스(high density plasma source)를 통해 추가적인 에너지를 인가하여 박막의 밀도를 bulk 수준으로 증가시키고 내부 응력을 조절하는 연구에 대한 관심이 커지고 있다. 특히 grid를 이용하여 플라즈마 내 이온의 입사에너지를 증가시킴으로써, 기존 공정보다 고기능성 박막을 구현할 수 있다. 본 연구에서는 RF power를 이용한 inductively coupled plasma를 통해 플라즈마를 생성시킨 후 grid에 DC power를 인가하는 플라즈마 소스를 개발하였으며, 시뮬레이션을 통해 plasma density와 ion current density, ion energy 분석 및 grid 디자인을 하였다. 개발된 플라즈마 소스는 ion energy analyzer를 통해 RF power 및 grid에 인가하는 power의 세기에 따라 이온화 정도 및 이온의 입사에너지를 측정하였다.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.126-134
• /
• 1999

In this study, plasma source ion implantation was used to improve the wear properties of biocompatible titanium implant. In order to observe the effect of ion energy and dose on wear property of titanium implant, pin-on-disk type wear tests in Hank's solution were carried out. The friction coefficient of ion implanted specimens were increased from 0.47 to 0.65 under high energy and ion dose conditions. As increasing ion energy and ion dose, the amount of wear was reduced.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.2
• /
• pp.37-41
• /
• 2016

This paper presents the developed quench analysis code and protection circuit design for a superconducting magnet system of 28GHz electron cyclotron resonance (ECR) ion source. The superconducting magnet is composed of a hexapole magnet and four solenoid magnets located outside of the hexapole one. All magnets are wound with NbTi composite wire and impregnated by epoxy. By using the developed characteristic analysis code, the normal zone resistance, decaying current and temperature rising can be estimated during quench. Also, the stored magnetic energy is successfully consumed from the series resistor of the designed protection circuit. The analytical results are compared with the experimental results to verify the developed quench analysis code and protection circuit.

• Journal of the Korean Vacuum Society
• /
• v.21 no.2
• /
• pp.78-85
• /
• 2012

In order to improve the adhesion between poly-monochloro-para-xylylene (Parylene-C) film and Aluminum thin film, the surface of Parylene-C film was irradiated by ${O_2}^+$ and $Ar^+$ ion beam generated by duoplamatron ion source. The ion dose of $Ar^+$ and ${O_2}^+$ was changed from $5{\times}10^{14}$ to $1{\times}10^{17}/cm^2$ and the ion beam energy was 1 kV. Contact angles of water on Parylene-C modified by $Ar^+$ and ${O_2}^+$ ion irradiation decreased from $78^{\circ}$ to around $17^{\circ}$, and $9^{\circ}$, respectively. X-ray photoelectron spectroscopy analysis shows that the hydrophilic groups were formed on the surface of Parylene-C by chemical reaction between the unstable chains induced by the ion irradiation and oxygen ions or residual oxygen gas. The hydrophilic groups were identified as C-O bond, C=O bond and (C=O)-O bond. The cross cut tape test which was applied to characterize the adhesion between Al thin film and Parylene-C film modified by ${O_2}^+$ ions irradiation shows that the adhesion strength was improved as increasing ion dose.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.4
• /
• pp.179-185
• /
• 2009

Diamond-like carbon(DLC) films were deposited by linear ion source(LIS)-physical vapor deposition method changing the anode voltages from 800 V to 1800 V, and characteristics of the films were investigated using residual stress tester, nano-indentation, micro raman spectroscopy, scratch tester and Field Emission Scanning Electron Microscope(FE-SEM). The results showed that the residual stress and hardness increased with increasing the ion energy up to anode voltage of 1400 V. It was also found that the content of $SP^3$ carbon increased with increasing the anode voltage $SP^3/SP^2$ ratio through investigation of $SP^3/SP^2$ ratio by the micro-raman analysis. From these results, it can be concluded that the physical properties of DLC films such as residual stress and hardness are increased with increasing the anode voltage. These results can be explained that 3-dimensional cross-links between carbon atoms and Dangling bond are enhanced and the internal compressive stress also increased with increasing the anode voltage. The optimal anode voltage is considered to be around 1400 V in these experimental conditions.

• Journal of Environmental Science International
• /
• v.2 no.4
• /
• pp.291-297
• /
• 1993

The COD values and chloride ion concentrations of the Taewha river flowing through Ulsan area were determined along the main stream and the relationships between CODs and chloride ion concentrations were described. The results showed that the middle-upper stream and downstream of the Taewha river were polluted deeply with municipal sewage and self-purification occured in the middle-downstream of the river. When domestic sewage is a main source of pollutants, and is especially the only source of chloride in the stream water, the ratio of COD/[$\textrm{Cl}^{-}$] will be utilizable as a measure of self-purification of the stream.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.4
• /
• pp.361-368
• /
• 1998

Acid rainwater samples were collected during 4 years from 1992 in Pusan area nearby seaside. Ionic composition of early and succeeding rainwater were investigated to identify emission sources. pH and Electronic Conductivity of samples were measured immediately after sampling. Major ion concentrations of rain samples were Na+, Ca2+, Mg2+, K+, NH4+, SO42-, NO3-, Cl- which were analyzed by ion Chromatography. 55% of early rainwater and 90% of succeeding rainwater were identified below pH 5.6. Because, Na+, K+, Ca2+ were washed mostly in early rainwater, as a result, pH values were increased by increasing rainfall amounts. It was studied that pH value was varied from ambient ion component, rainfall, and rain intensity. From the principal component analysis result, the dominant components of acid rainwater were Na+, K2+, Mg2+, Ca2+, the elements were contributed soil and marine source, the second components nuts -SO42-, SO4a-, NO3-, nuts -Ca2+ originated from man - made source.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.755-760
• /
• 2012

In this study, three dimensional cutting force components and surface roughness appeared in high speed cutting by using tungsten carbide endmill tools implanted ion or not found mutual relations through several analysis of statistical dispersion. It is showed that cutting force(Fx) is affect with spindle speed and feed rate, cutting force(Fy) is affect with spindle speed and ion implantation time and cutting force(Fz) is affect with feed rate in interaction through the statistical method of ANOVA of cutting force and surface roughness, it is analyzed that it is affected of spindle speed and feed rate in surface roughness.

• Journal of Information Display
• /
• v.5 no.1
• /
• pp.1-6
• /
• 2004

Ion shower doping with a main ion source of $P_2H_x$ using a source gas mixture of $PH_3/H_2$ was conducted on excimer-laser- annealed (ELA) poly-Si. The crystallinity of the as-implanted samples was measured using a UV-transmittance. The measured value of as-implanted damage was found to correlate well with the one calculated through/obtained from TRIM-code simulation. The sheet resistance was found to decrease as the acceleration voltage increased from 1 kV to 15 kV at a doping time of 1 min. However, it increases as the acceleration voltage increases under severe doping conditions. Uncured damage after furnace annealing is responsible for the rise in sheet resistance.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.33-40
• /
• 2010

In this research, the effects for surface Improvement of plasma ion implanted carbide endmill tools were observed by measuring cutting forces and tools wear affecting surface roughness in high speed cutting. From the 2nd ion mass analysis, the oxidation layer was found to be built up by sputtering. The residual gas contamination of oxygen was found to be contained impurities in nitrogen gas. The plasma implanted ion was found to be spreaded, especially the nitrogen was implanted up to 150nm depth as impressed voltage and ion implanting time. It is analyzed as bring surface improvement by spreading deeply forming oxidation on surface. The factors in Analysis of Variance(ANOVA) about mutuality cause reference of cutting force. The cutting force Fx is affected by the interaction of spindle rpm and federate, the cutting force Fy is influenced by spindle rpm and time injected ion, and cutting force Fz is affected by the interaction of impressed voltage and feedrate. Also, it was found that the cutting forces of implanted tools become lower and the surface roughness is improved by the effect of nitrogen according to the implantation.