• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.85-92
• /
• 2002

In this study, we analyzed and experimented micro-strip line inductors and capacitors for a SAW duplexer, an important devise for mobile communication. For SAW duplexers, micro-strip line lumped elements must have small impedance values, below several tens of nH or several tens of pF, and a small area pattern. In this study, we performed theoretical analysis of flat line type, meander line type, and spiral line type inductors and interdigital capacitors on a LiTaO$_3$ Piezo-crystal. We proposed a measurement method to evaluate small values of lumped elements accurately with network analyzer. In experiments, we confirmed validity of the theoretical analysis method through fabrication and characterization of micro-strip line lumped elements. The analysis method in this paper can be applied to SAW duplexers well as other microwave devices.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.530-535
• /
• 2021

In this paper, the design method for a chipless RFID tag using ELC resonators is proposed. A four-bit chipless RFID tag is designed in a two by two array configuration using three ELC resonators with different resonant peak frequencies and one compact IDC resonator. The resonant peak frequency of the bistatic RCS for the IDC resonator is 3.125 GHz, whereas those of the three ELC resonators are adjusted to be at 4.225 GHz, 4.825 GHz, and 5.240 GHz, respectively, by using the gap between the capacitor-shaped strips in the ELC resonator. The spacing between the resonators is 1 mm. Proposed four-bit tag is fabricated on an RF-301 substrate with dimensions of 50 mm×20 mm and a thickness of 0.8 mm. It is observed from experiment results that the resonant peak frequencies of the fabricated four-bit chipless RFID tag are 3.290 GHz, 4.295 GHz, 4.835 GHz, and 5.230 GHz, respectively, which is similar to the simulation results with errors in the range between -2.3% and 0.2%.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.627-632
• /
• 2020

In this paper, we have studied a development of a humidity sensor using a microwave sensor based on a microstrip defected ground structure coated with polyvinyl alcohol. A high-sensitivity microwave sensor, which is sensitive to the changes in the permittivity of the material under test, is designed by adding an interdigital capacitor-shaped defected ground structure to the ground plane of a microstrip line. Polyvinyl alcohol, a polymer material whose permittivity varies depending on humidity, is coated with a thin thickness on the defected ground structure of the proposed microwave sensor, and the changes in the resonance frequency and magnitude of the transmission coefficient for the microwave sensor according to humidity are measured. When relative humidity increases from 40% to 80% in 10% increments at a temperature of 25 degrees using a temperature/humidity chamber, the resonant frequency of the transmission coefficient decreases from 1.475 GHz to 1.449 GHz, and the magnitude is increased from -32.90 dB to -25.67 dB.

• Journal of Advanced Navigation Technology
• /
• v.26 no.6
• /
• pp.516-521
• /
• 2022

In this paper, a compact 4-bit chipless RFID(radio frequency identification) tag using a modified ELC(electric field-coupled inductive-capacitive) resonator and multiple slot resonators is proposed. The modified ELC resonator uses an interdigital-capacitor structure in the conventional ELC resonator to lower the resonance peak frequency of the RCS. The multiple slot resonators are designed by etching three slots with different lengths into an inverted U-shaped conductor. The resonant peak frequency of the RCS for the modified ELC resonator is 3.216 GHz, whereas those of the multiple slot resonators are set at 4.122 GHz, 4.64 GHz, and 5.304 GHz, respectively. The proposed compact four-bit tag is fabricated on an RF-301 substrate with dimensions of 50 mm×20 mm and a thickness of 0.8 mm. Experiment results show that the resonant peak frequencies of the fabricated four-bit chipless RFID tag are 3.285 GHz, 4.09 GHz, 4.63 GHz, and 5.31 GHz, respectively, which is similar to the simulation results with errors in the range between 0.78% and 2.16%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.487-493
• /
• 2001

In this paper, A new microstrip bandpass filter is proposed. The novelty of the proposed structures is to use a interdigital capacitor and embeded slot that are fanned on a patch resonator such that its insertion loss and size can be significantly reduced simultaneously. As a result, it is found that the resonant frequency of patch filter designed at 5 GHz is decreased to 1.8946 GHz and the insertion loss is reduced from -2.168 dB to -0.379 dB. This proposed filter has small size and low insertion loss in comparison with the conventional parallel edge coupled bandpass filter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.3 s.94
• /
• pp.253-259
• /
• 2005

In this paper, BaSrTiO$_{3}$(BST) thin film tunable interdigital capacitor using low cost silicon substrate instead of expensive single-crystalline substrate is presented. The tunable capacitor in which BST thin film is deposited by PLD has operation frequency and applied bias up to 4 GHz and 50 V, respectively. The maximum tunability in capacitance is found to be 30$\%$, for an applied field of 5 kV/cm at a bias of 50 V. Therefore, it has been shown that the BST microwave tunable capacitor can be integrated onto Si substrate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1563-1572
• /
• 1995

The on-line cure monitoring during the cure process of fiber reinforced resin matrix composite material is important for the better quality and productivity. Among several cure monitoring methods, the dielectrometry that uses electrodes as its sensor is known to be the most promising method. In this study, the sensitivity of the dielectric sensor for the on-line cure monitoring was analyzed by finite element method and compared to the experimental results. Using the analytical results, the equation for the capacitance of the sensor was derived. Also, the optimal sensor design method was suggested after analyzing several different sensor shapes.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1090-1095
• /
• 2003

In this paper, the modeling and design of high-Q multilayer passives and multilayer diplexer for GSM/DCS applications designed and fabricated using these passives have been investigated.. To miniaturize the system, configurations of inductor and capacitor have involved a square spiral structure and a vertically-interdigitated capacitor similar to 3D interdigital structure, respectively. Multilayer diplexers for GSM/DCS applications were designed and fabricated to apply high-Q multilayer passives to practical systems, which were designed by the proposed structural and equivalent circuit model. LPF for GSM band had the passband insertion loss of less than 0.55 dB, the return loss of more than 12 dB, and the isolation level of more than 26 dB by locating attenuation pole at 1800 MHz. HPF for DCS band had the passband insertion loss of less than 0.82 dB, the return loss of more than 11 dB, and the isolation level of more than 38 dB by locating attenuation pole at 930 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.162-172
• /
• 2011

In this paper, a design and fabrication of 4 W power amplifier for the WiMAX frequency band(2.3~2.7 GHz) are presented. The adopted active device is a commercially available GaN HEMT chip of Triquint Company, which is recently released. The optimum input and output impedances are extracted for power amplifier design using a specially self-designed tuning jig. Using the adopted impedances value, class-F power amplifier was designed based on EM simulation. For integration and matching in the small package module, spiral inductors and interdigital capacitors are used. The fabricated power amplifier with $4.4{\times}4.4\;mm^2$ shows the efficiency above 50 % and harmonic suppression above 40 dBc for second(2nd) and third(3rd) harmonic at the output power of 36 dBm.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.36-40
• /
• 2013

A novel design method of ultra wideband bandpass filter using CRLH transmission line with Dumbell type DGS is presented in this paper. Defected Ground Structure and microstrip interdigital capacitor are used to design the ultra wideband (UWB) filter. CRLH transmission line has composite characteristics of low pass and high pass filter. As control of cutoff frequency of low pass and high pass response on CRLH transmission line, we can get characteristic of UWB filter. We designed and simulated for CRLH transmission lines with one, two, four, and eight cells. A UWB filter using four cells CRLH is designed and fabricated to verify the results. The characteristics of designed filter have center frequency of 5GHz and relative bandwidth of 88%.