• Membrane Journal
• /
• v.3 no.2
• /
• pp.60-69
• /
• 1993

The polyamic acid (PAA) based on 3,3', 4,4'-benzophenonetetracarboxylic dianhydride(BTDA)-3,3', 4,4'-dipheylsulfonetetracarboxylic dianhydride(BAPP), 2,2-bis(4-[4-aminophenoxyl]phenyl) propane(DSDA)-3,3', 4,4'-dipheylsulfonetetracarboxylic dianhydride(BAPP), and 3,3',4,4'-benzophenonetetracarboxylic dianhydride(BTDA)-4,4'-oxydianiline(4,4'-ODA) was synthesised. The casted PAA films were partially imidised and the permeation properties of these PAA films for $O_2$ and $N_2$ were investigated according to the degree of imidisation. When the degree of imidisation was increased by curing, the permeabilities of the PAA films were increased for a while and then decreased. These results show that the increase of gas permeation by the disappearence of strong hydrogen bond is larger than the decrease of gas permeation by the dense effect. The decrease of hydrogen bond between molecular chains of PAA suddenly increases the vibration of the chain to make holes but the compaction in polymer chain gradually decreases the gas permeation. The largest values of permeability of BTDA-BAPP, DSDA-BAPP and BTDA-4,4'-ODA film was 8.3, 0.3 and 0.8 barrer respectively, and the imidisation content corresponding to the values of the largest permeability was 37, 47 and 55% each. But the permselctivities of the PAA films were not changed by the variation of the degree of imidisation.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.331-334
• /
• 2006

In this study, the ultra-fine fibers (UFs) having an alignment were prepared by electrospinning process, using different collectors made from various materials and collecting methods. A spinning solution was prepared by dissolving poly(amide-co-imide) (PAI) in NMP. The UFs were prepared by using various collectors and collecting methods, and the fibrous shapes were observed by SEM. As a result, a sort of materials of collectors and the collecting methods had not influenced on the average diameters of fibers but the forms of them. The just accumulated UFs on the collectors formed net structures, which had no alignment. On the contrary, the continuously collected UFs formed long fibers with alignment. It was found that the water collector played the roles of the fiber haul, temporary collector, moving path of fibers, and caused some friction between fibers and water, attributed to the formation of continuous UFs at a suitable collecting speed.

• Applied Chemistry for Engineering
• /
• v.10 no.2
• /
• pp.319-323
• /
• 1999

Asymmetric polyetherimide membranes were prepared by phase inversion method. In the modification of the skin layers of polyetherimide membranes, the effects of NaOH concentration on the morphology and pervaporation separation of water-isopropanol mixtures were investigated. With increasing concentration of NaOH solution, polyamicacid structure was formed by the hydrolysis of imide group of polyetherimide, and the thickness of dense layer of the asymmetric membrane increased. In the pervaporation separation of water-isopropanol mixtures the overall permeation rate decreased and the separation factor increased with increasing concentration of NaOH solution. However, when the concentration of NaOH solution was very high, the permeation rate increased but separation factor decreased. From these results, it was found that the permeation behaviors of asymmetric polyetherimide membranes depended upon the concentration of NaOH solution. These modified membranes showed that both the permeation rate and separation factor increased as the operating temperature increased.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.167-172
• /
• 2012

A new type of thermoplastic elastomer (TPE) based on EPDM ionomer as an elastomer and polyamide-6 as a reinforcing crystalline polymer was prepared and the thermal properties of TPEs were investigated. Especially effects of neutralization of maleated EPDM (MA-EPDM) to prepare EPDM ionomer with zinc oxide and the content of polyamide-6 on the thermal properties of the blends were investigated. Both the neutralization and blending were carried out employing a twin screw extruder. It was found that the neutralization of MA-EPDM results in the increase of cooling crystallization temperatures. Polyamide-6 plays the role of reinforcing filler in the blends due to the high crystallinity. Fine dispesion of polyamide-6 in the blends was confirmed and attributed to the imide formation between the maleic anhydride of MA-EPDM and amine group of polyamide-6. TPEs based on EPDM ionomer/Polyamide-6 blends showed balanced mechanical properties with improvement in heat resistance.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.632-639
• /
• 2014

2,7-Dihydroxynaphthalene bis(trimellitate anhydride) (2,7-TA) was synthesized from trimellitic anhydride chloride and 2,7-dihydroxynaphthalene. Copolyimides (Co-PI) containing ester group were synthesized from 2,7-TA, pxylylenediamine, and 2,2'-bis(trifluoromethyl)benzidine (TFB). The Co-PI films were obtained from poly(amic acid) by solution casting through thermal imidization on a glass plate. The thermal property, gas permeation, and optical transparency of the Co-PI films with various TFB monomer contents were investigated. These Co-PIs could be solution-cast into a flexible and tough film. The cast Co-PI films exhibited high optical transparency with a cut-off wavelength of 370~395 nm in UV-vis. absorption and a low yellow index value of 3.55~7.63. The thermal property of Co-PI films increased linearly with increasing TFB content. However, the oxygen permeation and optical transparency of the Co-PI films was found to worsen with increasing TFB content.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.8
• /
• pp.1749-1754
• /
• 2009

Solubilities of carbon dioxide (C$O_2$) in a series of fluorine-free room temperature ionic liquids (RTILs), dialkylimidazolium dialkylphosphates and dialkylimidazolium alkylphosphites, were measured at 313∼333 K and pressures up to 5 MPa. Henry’s law coefficients as the solubility parameter of C$O_2$ in RTILs were derived from the isotherm of fugacity versus C$O_2$ mole fraction. The C$O_2$ solubility in a phosphorus-containing RTIL was found to increase with the increasing molar volume of the RTIL. In general, dialkylimidazolium dialkylphosphate exhibited higher absorption capacity than dialkylimidazolium alkylphosphite as long as the RTILs possess an identical cation. Among RTILs tested, 1-butyl-3-methylimidazolium dibutylphosphate [BMIM][B$u_2PO_4$] and 1-butyl-3-methylimidazolium butylphosphite [BMIM][BuHP$O_3$] exhibited similar Henry’s law coefficients to 1-butyl-3-methylimidazolium bis (trifluoromethylsulfonyl)imide ([BMIM][T$f_2$N]) and 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][B$F_4$]), respectively. The Krichevsky-Kasarnovsky equation was employed to derive the C$O_2$ solubility parameter (Henry’s law coefficient) from the solubility data measured at elevated pressures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.399-402
• /
• 1998

Electroluminescent(EL) devices based on organic thin films have attracted lots of interests in large-area light-emitting display. One of the problems of such device is a lifetime, where a degradation of the cell is possibly due to an organic layers thickness, morphology and interface with electrode. In this study, light-omitting organic electroluminescent devices were fabricated using Alq$_3$(8-hydroxyquinolinate aluminum) and TPD(N,N'-diphenyl-N,N'-bis(3-methylphenyl(1-1\`-biphenyl]-4,4'-diamine). Where Alq$_3$ is an electron-transport and emissive layer, TPD is a hole-transport layer. The cell structure is ITO/TPD/Alq$_3$/Al and the cell is fabricated by vacuum evaporation method. In a measurement of current-voltage characteristics, we obtained a turn-on voltage at about 9 V. We also investigated stability of the devices using buffer layer with blend of PEI (Poly ether imide) and TPD by varying mot ratios between ITO and Alq$_3$. In current-voltage characteristics measurement, we obtained the turn-on voltage at about 6 V and observed an anomalous behavior at 3∼4 V. And we used other buffer layer of PEDT(3,4-pyrazino-3',4'-ethylenedithio-2,2',5,5'-tetrathiafulvalenium) with ITO/PEDT/TPD/Alq$_3$Al structure. We observed a surface morphology by AFM(Atomic Force Microscopy), UV/visible absorption spectrum, and PL(Photoluminescence) spectrum. We obtained the UV/visible absorption peak at 358nm in TPD and at 359nm in Alq$_3$, and the PL peaks at 410nm in TPD and at 510nm in Alq$_3$. We also studied EL spectrum in the cell structure of ITO/(TPD+PEI)/Alq$_3$/Al.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.194-200
• /
• 2020

Perylene bisimide derivatives are developed for red organic phosphor because of their advantages, such as excellent luminous efficiency and high thermal stability. Despite these advantages, they have poor solubility characteristics in organic solvents and short emission wavelength as red organic phosphor for hybrid light-emitting diodes (LEDs). In this study, we prepared terrylene bisimide using a coupling reaction and swallow-tail imide group, which has excellent solubility. The structures and properties of swallow-tail terrylene bisimide (9C) were analyzed using ¹H-nuclear magnetic resonance (¹H-NMR), Fourier-transform infrared (FT-IR), UV/Vis spectroscopy, and thermal gravimetric analysis (TGA). The maximum absorption wavelength of (9C) in the UV/Vis spectrum was 647 nm, and the maximum emission wavelength was 676 nm. In the TGA, (9C) demonstrated good thermal stability with less than 5 wt% weight loss up to 415℃. In the solubility test, (9C) has a good solubility of more than 5 wt% in chloroform and dichloromethane. When the compounds (9C) were mixed with PMMA (polymethly methacrylate), the films showed peaks at 680 nm in the PL spectra. The results verify the suitability of (9C) as a red organic phosphor for hybrid LEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.33-33
• /
• 2007

SoP-L 공정은 유전율이 상이한 재료를 이용하여 PCB 공정이 가능하고 다른 packaging 방법에 비해 공정 시간과 비용이 절약되는 잠정이 있다. 본 연구에서는 SoP-L 기술을 이용하여 Si 기판의 함몰에 판한 공정의 안정도와 함몰 시 제작된 때턴의 특성의 변화에 대해 관찰 하였다. Si 기판의 함몰에 Active device를 이용하여 특성의 변화를 살펴보고 공정의 안정도를 확립하려 했지만 Active device는 측정 시 bias의 확보와 특성의 민감한 변화로 인해 비교적 측정이 용이하고 공정의 test 지표를 삼기 위해 passive device 를 구현하여 함몰해 보았다. Passive device 의 제작 과정은 Si 기판 위에 spin coating을 통해 PI(Poly Imide)를 10um로 적층한 후에 Cr과 Au를 seed layer로 증착을 하였다. 그리고 photo lithography 공정을 통하여 photo resister patterning 후에 전해 Cu 도금을 거쳐 CPW 구조로 $50{\Omega}$ line 과 inductor를 형성하였다. 제작 된 passive device의 함몰 전 특성 추출 data와 SoP-L공정을 통한 함몰 후 추출 data 비교를 통해 특성의 변화와 공정의 안정도를 확립하였다. 차후 안정된 SoP-L 공정을 이용하여 Active device를 함몰 한다면 특성의 변화 없이 size 룰 줄이는 효과와 외부 자극에 신뢰도가 강한 기판이 제작 될 것으로 예상된다.

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.580-586
• /
• 2008

Copolyimides were synthesized from 4,4'-(hexafluoroisopropylidene)diphthalic anhydride (6FDA) and 1,3-bis(3-aminophenoxy)benzene (BAPB) with different mole ratios of 2,2-bis[4-(4-aminophenoxy)pheny1]hexafluoropropane (BAPP). The solution cast film of poly(amic acid) (PAA) was heat treated at different temperatures to create copolyimide films. The PI copolymer films were found to exhibit good optical transparencies. The thermomechanical properties, morphology, and optical transparency of PI films were examined using fourier transform infrared spectroscopy (FT-IR), wide-angle X-ray diffraction (XRD), scanning electron microscopes (SEM), differential scanning calorimeter(DSC), thermo-gravimetric analyzer (TGA), universal tensile machine (UTM), and IN - Vis. spectrometer. The glass transition temperature ($T_g$), ultimate strength, and initial modulus linearly increased with increasing BAPP mole fraction. However, thermal stability($T_D{^i}$) of the copolyimide remains constant regardless of BAPP loadings. It was found, however, that the optical transparency decreases slightly upon increasing the BAPP content because of the formation of the charge transfer complexes.