• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.297-300
• /
• 1987

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.6 s.312
• /
• pp.27-32
• /
• 2006

A temperature-compensated hygrometer has been developed using resistive humidity sensors. It consist of a sine wave generator, logarithm converters, rectifiers, and amplifiers. The hygrometer accomplishes the linearization and temperature compensation of sensor characteristics. The theory of operation is presented and experimental results are used to verify theoretical predictions. The experimental results show that the conversion sensitivity of the hygrometer is about 24.8 mV/%RH and the linearity error of the conversion characteristic is less than 17.2 % over a relative humidity range from 30 to 80 %RH. The results also show that the temperature coefficient of the output voltage is less than $10149ppm/^{\circ}C$ over a temperature range from 22 to $40^{\circ}C$.

• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.15-21
• /
• 1995

In this paper, $TiO_{2}-V_{2}O_{5}$ humidity sensors are fabricated by Sol-Gel method. For the establishment of optimum processing condition which is good humidity sensitive characteristics for specimens, their microstructures and crystalline-structures are analysed. Grain size increases with substitution rate of $V^{5+}$ on $Ti^{4+}$ site. From the analysis of XRD, $V^{5+}$ peak can't confirm with $V_{2}O_{5}$ rate. Their humidity sensitive characteristics is good at 1mol% of $V_{2}O_{5}$ rate and heat-treated at $700^{\circ}C$. The capacitance of specimens decreases with frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.142-145
• /
• 1993

$TiO_2-V_2O_5$ thin films are fabricated by Sol-Gel method and humidity sensing properties have been investigated. As the results of humidity sensing properties of thin films fabricated as humidity sensor, it is confirmed to have good humidity sensing properties in high humidity and low frequency regions.

• Journal of Sensor Science and Technology
• /
• v.12 no.6
• /
• pp.241-248
• /
• 2003

An electrochemical humidity sensor was fabricated with poly(1,5-diaminonaphthalene) film coated on a gap of two splitted gold electrodes, which were made by vacuum deposition. Response currents according to humidity were measured by the potential sweep method and chronoamperometry. The stability of the polymer film was improved by double step chronoamperometry using the applied voltage of ${\pm}0.5$ Vdc. The response time determined by the pulse technique was about ${\sim}50$ msec and the relative standard deviation of current response was within ${\pm}5.0%$. The response current of the film was intrinsically humidity dependent. The film exhibited a non-linear but reproducible response in ordinary range of relative humidity. The linear equations were $I(nA)=0.28{\times}%RH-1.01$ between 10 to 70 %RH and $I(nA)=6.05{\times}%RH-403.21$ between 70 to 90 %RH.

• 한국전기화학회:학술대회논문집
• /
• 2000.04a
• /
• pp.5-5
• /
• 2000

• Korean Journal of Materials Research
• /
• v.4 no.2
• /
• pp.159-165
• /
• 1994

Two kinds of humidity sensor are made, one by anodizing pure aluminum and the other by evaporation Sn02 on the anodized pure alumia film, and their electrical characteristics are investigated in various humidity atmosphere. The change of surface resistance with humidity of $AI_2O_3/AI$ and $SnO_2-AI_2O_3/Al$ sensors are found to be $1.40 \times 10^{-2}\Omega$/RH and $1.56 \times 10^{-2}\Omega$/RH, respectively. The hysteresis phenomena associated with the irreversibility of surface resistance-humidity is less in $SnO_2-AI_2O_3/Al$ sensor than in $AI_2O_3/AI$. It is concluded that $SnO_2-AI_2O_3/Al$ film can be used as humidity sensor in room temperature region because temperature dependence of surface resistance of the film is found to be as $0.56 \times 10^{-2} \Omega /^{\circ}C$ in O~ $20^{\circ}C$ range, where as $2.50 \times 10^{-2} \Omega /^{\circ}C$ in 40-$50^{\circ}C$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.5
• /
• pp.397-403
• /
• 2015

In this study, water distribution inside a proton exchange membrane fuel cell (PEMFC) was measured experimentally. Water distribution is non-uniform because of vigorous chemical reaction and mass transport and has been difficult to measure experimentally. Therefore, much research relied on indirect measuring methods or numerical simulations. In this study, several mini temperature-humidity sensors were installed at the channel for measuring temperature and humidity of the flowing gas throughout the channel. Only one of two electrode channels was humidified externally, and the humidity distribution on the other side was measured, enabling the observation of water transport characteristics under various conditions. Diffusion through the membrane became more vigorous as the temperature of the humidifier rose, but at high current density, electro-osmotic drag became more effective than diffusion.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.412-417
• /
• 2022

Capacitive-type humidity sensors with a high sensitivity and fast response/recovery times have attracted a great attention in non-contact respiration biological signal monitoring applications. However, complicated fabrication processes involving high-temperature heat treatment for the hygroscopic film is essential in the conventional ceramic-based humidity sensors. In this study, a non-toxic ceramic/metal halide (BaTiO₃(BT)/NaCl) humidity sensor was prepared at room temperature using a solvent-free aerosol deposition process (AD) without any additional process. Currently prepared BT/NaCl humidity sensor shows an excellent sensitivity (245 pF/RH%) and superior response/recovery times (3s/4s) due to the NaCl ionization effect resulting in an immense interfacial polarization. Furthermore, the non-contact respiration signal variation using the BT/NaCl sensor was determined to be over 700% by maintaining the distance of 20 cm between the individual and the sensor. Through the AD-fabricated sensor in this study, we expect to develop a non-contact biological signal monitoring system that can be applied to various fields such as respiratory disease detection and management, infant respiratory signal observation, and touchless skin moisture sensing button.

• Industry Promotion Research
• /
• v.9 no.1
• /
• pp.31-38
• /
• 2024

In this study, evaluated the properties of layered silicate-based nanocomposite sensitive film. For the fabrication of nanocomposite materials, we selected organically modified layered silicate materials, specifically Cloisite^® and Bentone^®, which were treated with quaternary ammonium salts. The impedance of the humidity sensors containing organically modified montmorillonite/hectorite clay decreased with increasing relative humidity(RH%). In the case of the Cloisite^® humidity sensor exhibited slightly better impedance linearity and hysteresis compared to the Bentone^® 38 humidity sensor. Additionally the impedance of the sensor with Bentone^® 38 addition was the lowest when compared to the Cloisite^®-modified sensor. Comparing the Cloisite^®-modified sensors individually, we observed different moisture absorption characteristics based on the hydrophilic properties of the organic-treated materials. The response speed of Cloisite^® 93A tended to be slower due to differences in moisture evaporation rates influenced by the hydrophilic organic components. Based on these results, moisture barriers utilizing organically modified layered silicate materials may exhibit slightly lower moisture absorption properties compared to conventional polymer-based moisture barriers. However, their excellent stability, simple processing, and cost-effectiveness make them suitable for humidity sensor applications.