• 한국산업융합학회 논문집
• /
• 제23권1호
• /
• pp.73-81
• /
• 2020

This study analyzed the causes of failure of SCM435 bolts that fix the springs of automobile air brakes that have been fractured during use. The cause of failure was analyzed using SEM, EDS, metallogical microscope and Vickers hardness tester. In the fracture, the ratchet mark began at the outer boundary of crack origin, and the grains at crack origin were found to have clear intergranular corrosion. One SCM435 bolt was subjected to a stress of 398 MPa, it's a stress of about 80% of the fatigue limit. As a result of such a large applied stress, cracks occurred at the corrosion origin and were fractured. In order to prevent the SCM435 bolt from fracture, it is necessary to use the correct composition, the accuracy of heat treatment, preventing damage by external impact, preventing corrosion of the damage part by moisture, and introduction a compressive residual stress by peening.

• 상하수도학회지
• /
• 제34권1호
• /
• pp.61-73
• /
• 2020

Tetracycline is one of the most commonly used antibiotics in domestic and foreign livestock industries to suppress the growth of pathogens. Tetracycline has been reported as a non-biodegradable compound. Therefore it has been not completely removed in the sewage treatment process. In this study, tetracycline was degraded using liquid ferrate (VI). Based on these experiments, the optimal water condition (pH and water temperature) were selected, appropriate liquid ferrate (VI) dosage was calculated, and finally the degradation pathway was estimated with the intermediate products detected by LC/MS/MS. All degradation experiments were completed within 30 seconds and the optimal condition was obtained in basic condition (pH 10) at room temperature (20℃). And the appropriate molar ratio between tetracycline and liquid ferrate (VI) was 12.5:1. Finally, 12 intermediate products were detected with LC/MS/MS and the degradation pathways and the degradation pathways and proposed the degradation pathways.

• 대한의용생체공학회:의공학회지
• /
• 제25권6호
• /
• pp.565-573
• /
• 2004

본 연구에서는 심혈관시스템 내의 압력 변화를 감지하는 압수용체 중 가장 대표적인 대동맥 압수용체의 시뮬레이션을 위한 심활성도 압반사 제어모델을 제안하였다. 그리고 제안된 모델은 압반사 조절, 시간지연을 포함한 전기회로 모델들로 구성하였으며, 대동맥동의 압반사 조절시 시간지연이 심주기와 일회 심박출량에 주는 영향을 관찰할 수 있도록 하였다. 심활성도 압수용체 제어 모델에서 시간지연의 기전은 대동맥동 압수용체에서 감지된 압력 정보가 구심성 신경으로 전달되고, 이 정보는 중추신경을 거쳐 원심성 신경으로 전달되어 제어 기능을 수행한다. 제안된 모델의 시뮬레이션 결과 시간지연에 따라 심혈관시스템 변이성의 세가지 패턴을 관찰할 수 있었다. 먼저 시간지연이 2.5초 이상일 경우에는 대동맥압, 일회심박출량, 심박동수가 비주기적으로 발생하고 불규칙인 것을 관찰할 수 있었고, 시간지연이 0.1초에서 2.5초 사이일 경우에는 주기적인 진동이 발생함을 관찰할 수 있었다. 그리고 시간지연이 0.1초 이하인 경우에는 심박동수와 동맥압-심박동수의 궤적은 안정상태를 유지함을 관찰할 수 있었다.

• Journal of Mechanical Science and Technology
• /
• 제20권10호
• /
• pp.1702-1715
• /
• 2006

The increasing use of nano-positioners in a wide variety of laboratory and industrial applications has created a need for nano-mechatronics education in all engineering disciplines. The subject of nano-mechatronics is broad and interdisciplinary. This article focuses on the way nano-mechatronics is taught in department of mechanical engineering at Korea Advanced Institute of Science and Technology (KAIST). As one model of nano-positioning systems, design and experimental methodology is presented in this article. For design phase, the stiffness and resonant frequencies are found analytically and verified by using a commercial finite element analysis program. Next, for experimental phase, various tests are performed to access the performances of the designed nano-positioner, for example, sine-tracking, multi-step response and travel-range check etc. Finally, the definition of 'separation frequency' is described and some comments are discussed.

• 한국해양공학회지
• /
• 제18권6호
• /
• pp.101-107
• /
• 2004

In this paper, the design criteria of future container crane for megaships are investigated. The current loading/unloading capacity of a typical container crane, roughly 30 moves/hr, is too law to meet the requirements of future super containerships, which are expected over 15,000 TEU. After examining the transition of containerships through the years and studying the research trend in developed countries, the specifications of the container crane that can Meet a 15,000 TEU containership are proposed. The structure, trolley and hoist mechanism, outreach, backreach, capacity, speeds, durability, and stability of the future container crane are described.

• 한국전기전자재료학회논문지
• /
• 제35권1호
• /
• pp.66-71
• /
• 2022

The insulator used for the transmission line is a device that is bonded with a cap, pin, ceramic, and cement to withstand insulation capacity and mechanical load. The insulator design can help to reduce the dispersion of the electric field; thus, the optimization of today's design, especially as demanded power grows, is critical. The designs of four manufacturers were used to perform a comparative analysis. Under dry circumstances of the new product, an electric field distribution study was done with no pollutants attached. Manufacturer D's design has the best voltage uniformity of 24.33% and the arc length of 500 mm or more. Manufacturer C's design has an equalizing voltage of more than 2% higher than that of other manufacturers. The importance of the design of the insulator and the number of connections according to the installation conditions is very efficient for transmission lines that will increase in the future.

• 동력기계공학회지
• /
• 제21권5호
• /
• pp.79-85
• /
• 2017

Vickers hardness is an important material in the design and reliability is required. Therefore, these values are very important as the basic data for design, manufacture and development, and the identification of quantitative probability distribution characteristics such as mean and dispersion is a very important parameter in design. In this study, Vickers hardness was measured after artificially heat-treated in the temperature range 753K, where chrome depletion near the grain boundary occurred for three kinds of stainless steels, and the Vickers hardness were evaluated. From the results, Vickers hardness increased with increasing heat treatment temperature. In Weibull distribution for Vickers hardness, the dispersion of STS310S at 813K and 873K was small, and the dispersion of STS316L at 753K, 933K and 993K was small. Also, STS347H exhibited the lowest dispersion at 753K in three kinds of stainless steels. The scale parameter increased with increasing heat treatment temperature in three kinds of stainless steels.

• 한국정보통신학회논문지
• /
• 제18권10호
• /
• pp.2516-2522
• /
• 2014

우리나라는 해안선이 복잡하여 연안을 항해하는 선박이나 어선의 안전한 항해 및 조업을 위해 효과적인 항로표지 운영이 필요하다. 특히 대형등명기는 야간에 항상 점등되어 선박의 안전을 보장해야 한다. 등대에 설치된 대형등명기가 점등되지 않을 경우 자신의 선위를 확인할 수 없어 사고가 발생하기 쉬우며 이는 커다란 경제적 피해를 야기할 수 있다. 본 연구에서는 대형등명기의 상태정보를 감시 제어하는 대형등명기 모니터링 시스템을 설계하고 구현하였다. 이 시스템은 다양한 장애상황에 신속히 대처하여 해양 안전사고를 미연에 방지할 수 있도록 하는데 그 목적이 있다.

• 한국멀티미디어학회논문지
• /
• 제17권11호
• /
• pp.1354-1362
• /
• 2014

In order to solve the complicated problems faced by the spread of diversified information devices and changes in the user environment in recent years, the importance of training creative talent as well as the need for interdisciplinary convergent approach have emerged. As a future technology development project, convergence education with the design sector for training creative talent in the IT field is also urgent. In this study, we recognized the importance and problems of the convergent approach between IT and design sector by examining the convergence theory and cases with a focus on effective creativity development and sought a new direction for convergence education in the future by investigating the awareness on the convergent approach of college students and analyzing the results. This will be able to have significance as a basic study for discovering creative and innovative convergent talent in the IT and design sector in the future and strengthening basic competence.

• Journal of Microbiology and Biotechnology
• /
• 제16권3호
• /
• pp.355-359
• /
• 2006

The functional stability of mRNA is one of the crucial factors affecting the efficiency of in vitro translation. As the rapid degradation of mRNA in the cell extract (S30 extract) causes early termination of the translational reactions, extending the mRNA half-life will improve the productivity of the in vitro protein synthesis. Thus, a simple PCR-based method is introduced to increase the stability of mRNA in an S30 extract. The target genes are PCR-amplified with primers designed to make the ends of the transcribed mRNA molecule anneal to each other. When compared with normal mRNA, the mRNA with the annealing sequences resulted in an approximately 2-fold increase of protein synthesis in an in vitro translation reaction. In addition, sequential transcription and translation reactions in a single tube enabled direct protein expression from the PCR-amplified genes without any separate purification of the mRNA.