• Journal of Sensor Science and Technology
• /
• v.32 no.6
• /
• pp.432-440
• /
• 2023

This study introduces an efficient readout circuit designed for two-electrode electrocardiogram (ECG) recording, characterized by its low-noise and low-power consumption attributes. Unlike its three-electrode counterpart, the two-electrode ECG is susceptible to common-mode interference (CMI), causing signal distortion. To counter this, the proposed circuit integrates a common-mode charge pump (CMCP) with a window comparator, allowing for a CMI tolerance of up to 20 V_PP. The CMCP design prevents the activation of electrostatic discharge (ESD) diodes and becomes operational only when CMI surpasses the predetermined range set by the window comparator. This ensures power efficiency and minimizes intermodulation distortion (IMD) arising from switching noise. To maintain ECG signal accuracy, the circuit employs a chopper-stabilized instrumentation amplifier (IA) for low-noise attributes, and to achieve high input impedance, it incorporates a floating high-pass filter (HPF) and a current-feedback instrumentation amplifier (CFIA). This comprehensive design integrates various components, including a QRS peak detector and serial peripheral interface (SPI), into a single 0.18-㎛ CMOS chip occupying 0.54 mm². Experimental evaluations showed a 0.59 µV_RMS noise level within a 1-100 Hz bandwidth and a power draw of 23.83 µW at 1.8 V.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1951-1953
• /
• 2004

In this study, we propose a small high voltage power supply which use a half-bridge ZCS resonant and Cockroft-Walton on circuit, for ESP (Electrostatic Precipitator). This power supply transfers energy from ZCS resonant inverter to step-up transformer and the transformer secondary is applied to the Cockroft-Walton circuit for generating high voltage as discharging source of electrodes. It is highly efficient because its amount of switching losses are reduced by virtue of the current resonant half-bridge inverter, and also due to the small size, low parasitic capacitance in the transformer stage owing to the low number of winding turns of the step up transformer secondary combined with the Cockroft-Walton circuit. From these results, the best operational condition is obtained at the switching frequency of 9 kHz and the duty ratio of 50 % in this ESP.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.473-474
• /
• 2009

A miniaturized electrostatic column consists of a set of scan-deflector and lens components. Electrical noises of scan-deflectors have been classified by the applied voltage, and analyzed the noise effects of electron beam passing through the deflectors.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.170-172
• /
• 1990

In a large power transformer, an insulating oil is forced to circulate for cooling the heat generated by the losses within the windings and core. When oil flows and rubs against various materials, including insulating paper and steel, electrostatic charges are separated at the interface of the oil and the solid material. This paper considers the polarity and the streaming electrification of the various materials which are used in transformer. As a result of this study, it is confirmed that the leakage current on the solid material, such as paper, is charged negative. On the other hand, the solid material, such as steel, is positively charged.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.686-689
• /
• 2014

Electrostatic discharge has been considered as a major reliability problem in the semiconductor industry. ESD reliability is an important issue for these products. Therefore, each I/O (Input/Output) PAD must be designed with a protection circuitry that creates a low impedance discharge path for ESD current. This paper presents a novel Lateral Insulated Gate Bipolar (LIGBT)-based ESD protection circuit with latch-up immunity and high robustness. The proposed circuit is fabricated by using 0.18 um BCD (bipolar-CMOS-DMOS) process. Also, TLP (transmission line pulse) I-V characteristic of proposed circuit is measured. In the result, the proposed ESD protection circuit has latch-up immunity and high robustness. These characteristics permit the proposed circuit to apply to power clamp circuit. Consequently, the proposed LIGBT-based ESD protection circuit with a latch-up immune characteristic can be applied to analog integrated circuits.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.365-368
• /
• 1995

Charge decay, thermally stimulated current (TSC), charging and discharging currents(I) are measured for corona-charged composite insulating materials. In this study, We will make an experiment in charge decay on composite material surface, TSC, polarity effect and the others in order to analysis its mechanism. Especially, Fiber glass Reinforced Plastics(FRP) is the best composite material which has been so far. Therefore, Its worthy of notice to investigate its characteristic. And then some other materials will be focused on. This experiment measured characteristic of charge decay, dependence of discharging-time and other electrostatic characteristics on FRP.

• Proceedings of the KIEE Conference
• /
• 1984.07a
• /
• pp.226-229
• /
• 1984

A novel high intensity charging device has been developed for the control of the submicron particles, such as the diesel soot particulates, which are very hard to charge highly by any means of the conventional charging device. Having new corona electrodes of a multineedle disk with the corona field-control electrodes in the outer-cylinder electrode, extremely intense and stable coronas on there sharp points expanding both radially and axially are established in the corona charging region between the multi-corona -needles and an outer-cylinder electrode. As a result, the maximum corona field intensity and current density of the charging device of the standard one on soot load in laboratory tests have been 8.5KV/cm(E=$2V_m$/D(1nD/d)) and $6.5{\mu}A/cm^2$ which enhance greatly the charging of soot particles about several 100 times higher than those obtained in conventional cylinder precipitators.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.10-10
• /
• 2010

ESD (Electrostatic Discharge) phenomenon occurs in everywhere and especially it damages to semiconductor devices. For ESD protection, there are some devices such as diode, GGNMOS (Gate-Grounded NMOS), SCR (Silicon-Controlled Rectifier), etc. Among them, diode and GGNMOS are usually chosen because of their small size, even though SCR has greater current capability than GGNMOS. In this paper, a novel SCR is proposed on the SOI (Silicon-On-Insulator) structure which has $1{\mu}m$ film thickness. In order to design and confirm the proposed SCR, TSUPREM4 and MEDICI simulators are used, respectively. According to the simulation result, although the proposed SCR has more compact size, it's electrical performance is better than electrical characteristics of conventional GGNMOS.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.164-169
• /
• 2002

This paper mainly discusses the hard breakdown of 2.2-nm-thick $SiO_2$ films. It is shown that the hard breakdown event of a 2.2-nm-thick $SiO_2$ film greatly depends on the applied electric field. It is strongly suggested that the local weak spots created by applying a low initial stress to a 2.2-nm-thick $SiO_2$film resist the onset of hard breakdown. In other words, it is anticipated that the stored electrostatic energy is fast dissipated by trap-assisted tunneling in 2.2-nm-thick $SiO_2$ film. Consequently, it is strongly suggested that 2.2-nm-thick $SiO_2$ films are intrinsically quite robust.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1994-1996
• /
• 2002

This paper reports a novel high-speed fluid injection system employing a simple magnetic micoractuator. This magnetic microacutator consists of current carrying copper beams and permanent magnet under the beams. There were many efforts to magnetic microactuator realization using conducting coils [1-2]. Even though many of magnetic microactuators were successfully fabricated and tested, it is true that most them suffer complex fabrication processes and thus higher production costs than electrostatic counterparts. In this research, efforts were concentrated on the microactuator realization that has simple structure, low production cost, and mass production possibility.