• Economic and Environmental Geology
• /
• v.42 no.4
• /
• pp.335-342
• /
• 2009

The effects of bacterial lysis on the rate of quartz dissolution were investigated under pH 7 condition using Bacillus subtilis cells which were either irradiated or non-irradiated with gamma ray. The amount of dissolved organic carbon (DOC) which resulted from bacterial lysis increased in slurries of quartz and bacteria mixture over experimental period. Lysis of non-irradiated bacteria led to the elevated concentration of dissolved silicon when compared with abiotic control. Concomitant increase in the amounts of DOC and dissolved silicon over time indicated that lixiviation of silicon from quartz was due to bacterial lysis. Higher amounts of DOC and dissolved silicon were present in the irradiated bacterial slurries than those of non-irradiated bacteria. The enhancement of quartz dissolution in the irradiated bacterial slurries was likely attributed to disruption of organic molecules in the bacterial cells by gamma ray and formation of effective ligands for quartz dissolution. The results suggest that the effects of bacterial lysis on mineral weathering rate should be considered for prediction of time for released radionuclides to migrate to surface biosphere in high level radioactive waste disposal site.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.41-46
• /
• 2012

In this study, poly(ethylene glycol) (PEG) was used as a hydrophilic polymer carrier to develop solid dispersion formulations for enhancing solubility and dissolution rate of pranlukast, one of poorly soluble drugs that has been broadly used for the treatment of asthma. PEG based solid dispersions with or without poloxamer were prepared by hot melting and solvent evaporation methods. The resultant solid dispersions were characterized by DSC and powder X-ray measurements, and their morphological properties were observed to be partially changed to amorphous state with reduced crystallinity. Dissolution and solubility tests showed that the solubility and dissolution rate of the solid dispersions were significantly enhanced. The solid dispersion formulation prepared by the hot melting method with a chemical composition of pranlukast:PEG:poloxamer = 1:5:1 demonstrated the most enhanced solubility and dissolution rate. The results suggest that the solid dispersions based on PEG and poloxamer are promising systems for the enhancement of solubility and bioavailability of pranlukast.

• Journal of Biomedical Engineering Research
• /
• v.11 no.1
• /
• pp.5-12
• /
• 1990

Calcium phosphate ceramics have been applied intensively to orthopaedic and dental implants by virtue of their osteoconductive nature. In an attempt to enhance the bone implant intergrity and Eta utility, these ceramics are deposited onto the porous surface of metallic implants. The coating procedure and the ensuing phase transformations of the ceramic alter the mechanical properties and surface chemistry of the ceramic layers as well as those of the substrate. These structural and compositional differences are directly related to the interaction mechanisms at the surface-active ceramicbone interface. Material and processing induced influences on dissolution, electrokinetic behavior, ceramic-metallic substrate interface and boRe growth enhancement are presented.

• Biomolecules & Therapeutics
• /
• v.4 no.4
• /
• pp.419-427
• /
• 1996

To solubilize practically insoluble biphenyl dimethyl dicarboxylate (DDB), which has been used for the treatment of chronic hepatitis as tablets or hard capsules, the solubilities of DDB in various hydrophilic, oily and hydrocarbon vehicles, and aqueous surfactant solutions were measured by high performance liquid chromatography. It was found that, among the vehicles studied, polyethylene glycol (PEG) 300 revealed the best solvency, and the solubility reached 17.6 mg/ml at 37$^{\circ}C$. The addition of glycyrrhizic acid ammonium salt (GAA) to DDB-PEG 300 solution (5-20 mg/g) inhibited the formation of precipitates, and at the concentration of 10 mg/g, any precipitaction was not observed even after 2 years at 4$^{\circ}C$. Furthermore, GAA markedly enhanced the permeation of DDB through the rabbit duodenal mucosa in a concentration dependent manner. The addition of copolyvidone (ca. 1.0%) to DDB-GAA-PEG 300 system (1 : 0.5 97.5 w/w) was most effective in preventing the considerable precipitation of DDB-PEG 300 solution (7.5 mg/750 mg) when mixed with water of 300-900 ml at 37$^{\circ}C$. GAA showed a synergistic effect in the prevention of precipitate formation. This finding suggests that this DDB formulation may form less precipitation when DDB soft capsules disintegrate and diffuse into the gastrointestinal fluid, resulting in improving the bioavailability Dissolution rate of DDB (7.5 mg) from sort elastic capsules of DDB-GAA-PEG 300 system was rapid. The supersaturation state was maintained for 2 hr at the concentration of 7.35$\pm$3.3 mg in 900 ml of water without precipitation. The total amount of DDB dissolved from this new formulation was 5.3 and 6.1 times higher, when compared to marketed DDB tablets (25 mg) and capsules (7.5 mg), respectively.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.3
• /
• pp.125-142
• /
• 2011

Solid dispersion, defined as the dispersion of one or more active ingredient in a carrier or matrix at solid state, is an efficient strategy for improving dissolution of poorly water-soluble drugs for enhancement of their bioavailability. Compared to other conventional formulations such as tablets or capsules, solid dispersion which can be prepared by various methods has many advantages. However, despite numerous studies which have been carried out, limitations for commercializing these products remain to be solved. For example, during the manufacturing process or storage, amorphous form of solid dispersion can be converted into crystalline form. That is, the dissolution rate of solid dispersion would continuously decrease during storage, resulting in a product of no value. To resolve these problems, studies have been conducted on the effects of excipients. In fact, modification of the solid dispersions to overcome these disadvantages has progressed from the first generation to the recent third generation products. In this review, an overview on solid dispersions in general will be given with emphasis on the various manufacturing processes which include the use of polymers and on the stabilization strategies which include methods to prevent crystallization.

• Journal of Sensor Science and Technology
• /
• v.12 no.5
• /
• pp.218-224
• /
• 2003

The devices of n-channel poly silicon thin film transistors(TFTs) hydrogenated by plasma, $H_2$ and $H_2$/plasma processes are fabricated. The carriers sensitivity characteristics are analyzed with voltage bias stress at the gate oxide. The parametric sensitivity characteristics caused by electrical stress conditions in hydrogenated devices are investigated by measuring the drain current, threshold voltage($V_{th}$), subthreshold slope(S) and maximum transconductance($G_m$) values. As a analyzed results, the degradation characteristics in hydrogenated n-channel polysilicon thin film transistors are mainly caused by the enhancement of dangling bonds at the poly-Si/$SiO_2$ interface and the poly-Si grain boundary due to dissolution of Si-H bonds. The generation of traps in gate oxide are mainly dued to hot electrons injection into the gate oxide from the channel region.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.327-335
• /
• 2006

In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.

• Environmental Engineering Research
• /
• v.21 no.4
• /
• pp.427-435
• /
• 2016

In this study, change in water-dissolved oxygen (DO) was analyzed under various synthetic water qualities and nanobubbles (NBs) application conditions, such as gas type, initial DO as well as water dissolved, suspended and organic matters contents. When oxygen, rather than air, was introduced into nitrogen-desorbed ultra-pure water, the stagnation time was significantly increased. It took ten days for DO concentration to drop back to saturation. The higher the initial DO concentration, the longer particles were observed above saturation due to particle stability improvement. The oxygen mass transfer rate of 0.0482 mg/L/min was found to reach a maximum at an electrolytic concentration of 0.75 g/L, beyond which the transfer rate decreased due to adsorption of negative ions of the electrolyte at the interface. High levels of turbidity caused by suspended solids have become a barrier to dissolution of NBs oxygen into the water solution, and thus affected the transfer performance. On the other hand, by applying NBs for just an hour, up to 7.2% degradation of glucose as representative organic matter was achieved. Thus, NBs technology would maintain a high DO extent for an extended duration, and thus can improve water quality provided that water chemistry is closely monitored during its application.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.60-66
• /
• 2002

The morphology, dynamic mechanical behavior and fracture behavior of polyetherimide (PEI)/dicyanate semi-interpenetrating polymer networks (semi-IPNs) with a morphology spectrum were analyzed. To obtain the morphology spectrum, we disported PEI particles in the procured dicyanate resin containing 300 ppm of zinc stearate catalyst. The semi-IPNs exhibited a morphology spectrum, which consisted of nodular spinodal structure, dual-phase morphology, and sea-island type morphology, in the radial direction of each dispersed PEI particle due to the concentration gradient developed by restricted dissolution and diffusion of the PEI particles during the curing process of the dicyanate resin. Analysis of the dynamic mechanical data obtained by the semi-IPNs demonstrated that the transition of the PEI-rich phase was shifted toward higher temperature as well as becoming broader because of the gradient structure. The semi-IPNs with the morphology spectrum showed improved fracture energy of 0.3 kJ/$m^2$, which was 1.4 times that of the IPNS having sea-island type morphology. It was found that the partially introduced nodular structure played a crucial role in the enhancement of the fracture resistance of the semi-IPNs.

• Carbon letters
• /
• v.16 no.2
• /
• pp.93-100
• /
• 2015

Surface modified carbon felts were utilized as an electrode for the removal of inorganic ions from seawater. The surfaces of the carbon felts were chemically modified by alkaline and acidic solutions, respectively. The potassium hydroxide (KOH) modified carbon felt exhibited high Brunauer-Emmett-Teller (BET) surface areas and large pore volume, and oxygen-containing functional groups were increased during KOH chemical modification. However, the BET surface area significantly decreased by nitric acid ($HNO_3$) chemical modification due to severe chemical dissolution of the pore structure. The capability of electrosorption by an electrical double-layer and the efficiency of capacitive deionization (CDI) thus showed the greatest enhancement by chemical KOH modification due to the appropriate increase of carboxyl and hydroxyl functional groups and the enlargement of the specific surface area.