• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.335-340
• /
• 2002

In this paper, the stress induced leakage currents of thin silicon oxides is investigated in the ULSI implementation with nano structure transistors. The stress and transient currents associated with the on and off time of applied voltage were used to measure the distribution of high voltage stress induced traps in thin silicon oxide films. The stress and transient currents were due to the charging and discharging of traps generated by high stress voltage in the silicon oxides. The transient current was caused by the tunnel charging and discharging of the stress generated traps nearby two interfaces. The stress induced leakage current will affect data retention in electrically erasable programmable read only memories. The oxide current for the thickness dependence of stress current, transient current, and stress induced leakage currents has been measured in oxides with thicknesses between 113.4${\AA}$ and 814${\AA}$, which have the gate area $10^3cm^2$. The stress induced leakage currents will affect data retention and the stress current, transient current is used to estimate to fundamental limitations on oxide thicknesses.

• Fire Science and Engineering
• /
• v.13 no.3
• /
• pp.19-26
• /
• 1999

$CO_2$ extinguishing system is the most $\phi$pular among the gas extinguishing system. $CO_2$ is usually stored with liquified state. But, it gasifies at the tip of nozzle when $CO_2$ was released through the pipe and head. A ro$\alpha$n temperature is very low when $CO_2$ was released. So electrical instrument, magnetic storage equipment and memory semiconductor are electrically or physically injured by cooling effect in a few minutes. So, we intend to find out temperature profile and electrical damage in compartment area, and supply basic d data for research and making standards and code through the full scale experiment. As result of experiment on the damage due to cooling effect from $CO_2$ extinguishing system, i instantaneous discharging temperature. was $-82.5^{\circ}C$ in average. An average temp. in the compartment after discharging $CO_2$ was $-40^{\circ}C$.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.23 no.3
• /
• pp.85-99
• /
• 2020

Reservoir is an important infrastructure of our society because it can store immense amount of water for various usages - manufacturing, agriculture, drinking, power generation, tourism etc. For maintenance of reservoir, various efforts in administrative and technological aspects are periodically conducted and monitoring the conditions of reservoir bed is the first priority for maintenance of reservoir. To check the conditions of reservoir bed, we measured depth of reservoir by using echo sounder, which is relatively reliable, prior to discharging of stored water and surveyed topography of reservoir by using UAV after discharging of water. Then, we conducted interpolation of measured depth of water by means of inverse distance weighting interpolation, Kriging interpolation, minimum curvature interpolation and radial basis function interpolation and calculated the volume of reservoir for each interpolation method. We compared the calculated volume of reservoir with the volume of water calculated by UAV after discharging of water and found the following results: First, as results of the above processes, we found that the Kriging interpolation was 97% correct in measurement of the volume of reservoir. Second, as results of comparison of differences between topographical areas and interpolated areas after selection of cross section for comparison, Kriging interpolation was found to have the most similar configuration with the topographical configuration by showing the least difference in the area of cross section. Therefore, it is determined that the optimal modeling of reservoir bed with the water depth data measured by echo sounder shall provide basic information for efficient maintenance of reservoir.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1523-1526
• /
• 2012

In this work, we prepared activated multi-walled carbon nanotubes/polyacrylonitrile (A-MWCNTs/C) composites by film casting and activation method. Electrochemical properties of the composites were investigated in terms of serving as MWCNTs-based electrode materials for electric double layer capacitors (EDLCs). As a result, the A-MWCNTs/C composites had much higher BET specific surface area, and pore volume, and lower volume ratio of micropores than those of pristine MWCNTs/PAN ones. Furthermore, some functional groups were added on the surface of the A-MWCNTs/C composites. The specific capacitance of the A-MWCNTs/C composites was more than 4.5 times that of the pristine ones at 0.1 V discharging voltage owing to the changes of the structure and surface characteristics of the MWCNTs by activation process.

• Journal of Powder Materials
• /
• v.22 no.1
• /
• pp.15-20
• /
• 2015

The composite of porous silicon (Si) and amorphous carbon (C) is prepared by pyrolysis of a nano-porous Si + pitch mixture. The nano-porous Si is prepared by mechanical milling of magnesium powder with silicon monoxide (SiO) followed by removal of MgO with hydrochloric acid (etching process). The Brunauer-Emmett-Teller (BET) surface area of porous Si ($64.52m^2g^{-1}$) is much higher than that before etching Si/MgO ($4.28m^2g^{-1}$) which indicates pores are formed in Si after the etching process. Cycling stability is examined for the nano-porous Si + C composite and the result is compared with the composite of nonporous Si + C. The capacity retention of the former composite is 59.6% after 50 charge/discharge cycles while the latter shows only 28.0%. The pores of Si formed after the etching process is believed to accommodate large volumetric change of Si during charging and discharging process.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.813-820
• /
• 2001

The Safety depressurization System(SDS) of KNGR prevents RCS from overpressurization by discharging high pressure and temperature coolant through the I-sparger into the IRWST during an accident. If IRWST water temperature rise locally, around the sparger, beyond $200_{\circ}$2000 F by the discharged coolant, unstable steam condensation can cause large pressure load on the IRWST wall. To investigate whether this condition can be avoided for the design basis event IOPOSRV(Inadvertent Opening of one Pilot Operated Safety Relief Valve), the flow and temperature distribution of water in the IRWST is calculated by using CFX 4.3 computational fluid dynamic code. According to the results, since pool water temperature does not exceeds temperature limit within 50 seconds after the opening of one POSRV, it can be assured that the integrity of IRWST wall is maintained.

• Journal of Korean Society of Transportation
• /
• v.6 no.1
• /
• pp.55-64
• /
• 1988

Prior to using any computer model, the program-embedded palameters showing significant differences from real world should be calibrated. This is especially true when the model is expected to be used fro various roadway and traffic condition. The calibration of TRANSYT model was conducted for the parameters of start-up delay, and lag, stop penalty(K), platoon dispersion factor, and saturation flow rate. The values of the parameters were obtained by theoretical methods from actual field measurements for discharging and arrival pattern. The sites elected for the study was an intersection of Dongil-Ro and Hwarang-Ro, and a 334 meter downstrean section from the intersection stop line on westbound Hwarang-Ro. The study results showed that the start-up delay was 2.6 sec, end lag was 1.0 sec, saturation flow rate was 2287 pcphgpl, platoon dispersion factor was 0.2-03, and stop penalty(K) was 32. However, since these parameters re apt to depend on traffic and roadway condition, it is doubtful whether the obtained values will be applicable to the area-wide situation other than this particular site.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.1
• /
• pp.35-41
• /
• 2017

We propose a novel multi-photodiode array (MPDA) based retinal implant IC with on/off stimulation strategy for a visual prosthesis with improved spatial resolution. An active pixel sensor combined with a comparator enables generation of biphasic current pulses when light intensity meets a threshold condition. The threshold is tuned by changing the discharging time of the active pixel sensor for various light intensity environments. A prototype of the 30-channel retinal implant IC was fabricated with a unit pixel area of $0.021mm^2$, and the stimulus level up to $354{\mu}A$ was measured with the threshold ranging from 400 lx to 13120 lx.

• Journal of Dental Anesthesia and Pain Medicine
• /
• v.18 no.4
• /
• pp.271-275
• /
• 2018

The purpose of this study was to report and discuss the diagnosis and treatment of obstructive atelectasis secondary to pus obstruction in a patient who had developed a maxillofacial abscess, and to review the literature on similar cases. Persistently discharging pus within the oral cavity can act as an aspirate, and may lead to obstructive atelectasis. Additionally, maxillofacial surgery patients should be carefully assessed for the presence of risk factors of obstructive atelectasis, such as, epistaxis after nasotracheal intubation, oral bleeding, and mucus secretion. Furthermore, patients with these risk factors should be continuously followed up by monitoring $SPO_2$, breath sounds, and chest x-ray.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.4
• /
• pp.15-21
• /
• 1977

In this paper, an analogical method for measuring the electrical characteristics of the silent discharge in the Na2CO3 electrolyte is proposed by using an electrical equivalent model which consist of charging and discharging circuits. The electrical equivalent model is constructed with the use of zener diode and capacitor, and the electrical characteristics can be obtained by the voltage and charge traces which appear a simple parallelogram on the oscilloscope. The area enclosed by the parallelogram could be considered of the energy input per cycle, and is independent of the applied voltage waveform but dependent on the maximum applied voltage.