• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.184-191
• /
• 2000

Properties of pad are investigated to find the relationship between the chemical mechanical polishing(CMP) results, such as material removal rate and within wafer non-uniformity(WIWNU), and its properties. Polishing pressure is considered as important factors to affect the results, so behavior of ordinary polymer is studied to define the polishing result affecting properties of pad. Experimental setup is devised to identify the behavior of pad and several different pads are used in chemical mechanical polishing experiments to verify the correlations between pad properties and polishing results. The results indicate that the viscoelastic properties of pad had relationships with the polishing results, and shows correlation between suggested properties of pad and polishing result.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.134-140
• /
• 2002

Chemical mechanical polishing of aluminum and photoresist using colloidal silica-based slurry was experimented. The effects of slurry pH, silica concentration, and oxidizer ($H_2O_2$) concentration on surface roughness and removal rate were studied. The optimum slurry conditions for reduction of micro-scratch were investigated. The optimum chemical mechanical polishing with the colloidal silica-based slurry was compared with conventional chemical mechanical polishing with alumina-based slurry. Chemical mechanical polishing of the aluminum with the colloidal silica-based slurry showed improved result but chemical mechanical polishing of the photoresist did not. The improved result was comparative with that of chemical mechanical polishing with filtered alumina-based slurry which one of desirable methods to reduce the micro-scratch.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.2
• /
• pp.53-57
• /
• 2007

In this study, a novel slurry containing ceria as the abrasive particles was analyzed in terms of its frictional, thermal and kinetic attributes for interlayer dielectric (ILD) CMP application. The novel slurry was used to polish 200-mm blanket ILD wafers on an $IC1000_{TM}$ K-groove pad with in-situ conditioning. Polishing pressures ranged from 1 to 5 PSI and the sliding velocity ranged from 0.5 to 1.5 m/s. Shear force and pad temperature were measured in real time during the polishing process. The frictional analysis indicated that boundary lubrication was the dominant tribological mechanism. The measured average pad leading edge temperature increased from 26.4 to $38.4\;^{\circ}C$ with the increase in polishing power. The ILD removal rate also increased with the polishing power, ranging from 400 to 4000 A/min. The ILD removal rate deviated from Prestonian behavior at the highest $p{\times}V$ polishing condition and exhibited a strong correlation with the measured average pad leading edge temperature. A modified two-step Langmuir-Hinshelwood kinetic model was used to simulate the ILD removal rate. In this model, transient flash heating temperature is assumed to dominate the chemical reaction temperature. The model successfully captured the variable removal rate behavior at the highest $p{\times}V$ polishing condition and indicates that the polishing process was mechanical limited in the low $p{\times}V$ polishing region and became chemically and mechanically balanced with increasing polishing power.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.5
• /
• pp.414-422
• /
• 2005

This paper shows the results of atomistic modeling for the Interaction between spherical nano abrasive and substrate In chemical mechanical polishing processes. Atomistic modeling was achieved from 2-dimensional molecular dynamics simulations using the Lennard-jones 12-6 potentials. We proposed and investigated three mechanical models: (1) Constant Force Model; (2) Constant Depth Model, (3) Variable Force Model, and three chemical models, such as (1) Chemically Reactive Surface Model, (2) Chemically Passivating Surface Model, and (3) Chemically Passivating-reactive Surface Model. From the results obtained from classical molecular dynamics simulations for these models, we concluded that atomistic chemical mechanical polishing model based on both Variable Force Model and Chemically Passivating-reactive Surface Model were the most suitable for realistic simulation of chemical mechanical polishing in the atomic scale. The proposed model can be extended to investigate the 3-dimensional chemical mechanical polishing processes in the atomic scale.

• Tribology and Lubricants
• /
• v.33 no.3
• /
• pp.106-111
• /
• 2017

Sapphire is an anisotropic material with excellent physical and chemical properties and is used as a substrate material in various fields such as LED (light emitting diode), power semiconductor, superconductor, sensor, and optical devices. Sapphire is processed into the final substrate through multi-wire saw, double-side lapping, heat treatment, diamond mechanical polishing, and chemical mechanical polishing. Among these, chemical mechanical polishing is the key process that determines the final surface quality of the substrate. Recent studies have reported that the material removal characteristics during chemical mechanical polishing changes according to the crystal orientations, however, detailed analysis of this phenomenon has not reported. In this work, we carried out chemical mechanical polishing of C(0001), R($1{\bar{1}}02$), and A($11{\bar{2}}0$) substrates with different sapphire crystal planes, and analyzed the effect of crystal orientation on the material removal characteristics and their correlations. We measured the material removal rate and frictional force to determine the material removal phenomenon, and performed nano-indentation to evaluate the material characteristics before and after the reaction. Our findings show that the material removal rate and frictional force depend on the crystal orientation, and the chemical reaction between the sapphire substrate and the slurry accelerates the material removal rate during chemical mechanical polishing.

• Tribology and Lubricants
• /
• v.38 no.1
• /
• pp.1-7
• /
• 2022

Chemical-mechanical polishing (CMP) process is a semiconductor process that planarizes a wafer surface using mechanical friction between a polishing pad and a substrate surface during a specific chemical reaction. During the CMP process, polishing pad conditioning is applied to prevent the rapid degradation of the polishing quality caused by polishing pad glazing through repeated material removal processes. However, during the conditioning process, uneven wear on the polishing pad is inevitable because the disk on which diamond particles are electrodeposited is used. Therefore, the abrasion of the polishing pad should be considered not only for the variables during the conditioning process but also when designing the CMP conditioning system. In this study, three design variables of the conditioning system were analyzed, and the effect on the pad wear profile during conditioning was investigated. The three design variables considered in this study were the length of the conditioner arm, diameter of the conditioner disk, and distance between centers. The Taguchi method was used for the experimental design. The effect of the three design variables on pad wear and uniformity was assessed, and new variables used in conditioning system design were proposed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.7-12
• /
• 2012

Chemical mechanical polishing(CMP) technology is faced with the challenge of processing new electronic materials. This paper focuses on the balance between chemical and mechanical reactions in the CMP process that is required to cope with a variety of electronic materials. The material properties were classified into the following categories: easy to abrade(ETA), difficult to abrade(DTA), easy to react(ETR) and difficult to react(DTR). The chemical and mechanical balance for the representative ETA-ETR, DTA-ETR, ETA-DTR and DTA-DTR materials was considered for defect-free surfaces. This paper suggests the suitable polishing methods and examples for each electronic material.

• Tribology and Lubricants
• /
• v.34 no.3
• /
• pp.115-122
• /
• 2018

Chemical mechanical polishing (CMP) is a hybrid processing method in which the surface of a wafer is planarized by chemical and mechanical material removal. Since mechanical material removal in CMP is caused by the rolling or sliding of abrasive particles, interfacial friction during processing greatly influences the CMP results. In this paper, the trend of tribology research on CMP process is discussed. First, various friction force monitoring methods are introduced, and three elements in the CMP tribo-system are defined based on the material removal mechanism of the CMP process. Tribological studies on the CMP process include studies of interfacial friction due to changes in consumables such as slurry and polishing pad, modeling of material removal rate using contact mechanics, and stick-slip friction and scratches. The real area of contact (RCA) between the polishing pad and wafer also has a significant influence on the polishing result in the CMP process, and many researchers have studied RCA control and prediction. Despite the fact that the CMP process is a hybrid process using chemical reactions and mechanical material removal, tribological studies to date have yet to clarify the effects of chemical reactions on interfacial friction. In addition, it is necessary to clarify the relationship between the interface friction phenomenon and physical surface defects in CMP, and the cause of their occurrence.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.263-268
• /
• 1999

Langasite, a new piezoelectric material was polished by CMP(chemical mechanical polishing). To enhance the polishing rate, alumina abrasives were added to commercial ILD1300 slurry which contains silica abrasive. The effect of added alumina 0 the silica slurry on the polishing rate and damage of langasite was investigated, Experimental results show that the polishing rate and roughness increases with increasing added alumina particle size, Crystallinity of the langasite is also lowered by alumina addition.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.11a
• /
• pp.48-51
• /
• 2004

Chemical Mechanical Polishing(CMP) is popularly used in production of semiconductor because of large area polishing ability probability of improvement for more integrated circuit. However, present CMP processing causes some non-uniformity errors which can be critical for highly integrated circuit. Previous studies predict that flow-field of slurry during CMP can create non-uniformity, but no quantitative measurement has conducted. In this study, using PIV, slurry velocity flow-field during CMP is measured by changing the ratio of RPM of pad and carrier with tuned PIV system adequate for small room in CMP machine and Cabot's non-groove pad Epad-A100. The result show that velocity of slurry is majorly determined by pad-rpm and the ratio of between carrier and pad rpm make some changes in streamlines.