• 한국잠사곤충학회지
• /
• 제39권2호
• /
• pp.146-153
• /
• 1997

The microsporidian infection with Nosema bombycis, reconfirmed its high virulence and transovarial tranmissibility, however, the characteristic symptom of the spots like pepper grains on the diseased larval skin was no more recognized by present varieties of the silkworm. Transovarial transmission rate detected from moth was above 90% in dead eggs or dead larvae in the rearing by mulberry leaves, 80% in the newly hatched larvae starved to death. Transovarially transmitted N. bombycis was easily observed from dead eggs and larvae, and were suggested an individual inspection of a few of dead eggs for detection of the pathogenic spores. The progeny population provided indicative factors on the sampling of predictive and corrective inspection. The higher concentration of N. bombycis spores included in the hindabdormal part of infected moth, applicative on the simple method of indivisual moth inspection. For the predictive inspection of growned 5th-instar larvae, N. bombycis infection was detectable without microscopic observation by the unique symptom of turbid milky-white spots on the silk gland. Inspection of the meconia artificially discharged from silkworm moth, was also succesful of microscopic observation before crossing, without killing or homogenize the moths. The results provided a basis of rational methods for the inspection of N. bombycis infection of the silkworm.

• 한국정밀공학회지
• /
• 제21권12호
• /
• pp.92-99
• /
• 2004

The formation degree of sustain (ITO pattern) decides quality of PDP (Plasma Display Panel). For this reason, it makes efforts in searching defects more than 30 un as 100%. Now, the existing inspection is dependent upon naked eye or microscope in off-line PDP manufacturing process. In this study developed prototype inspection system of PDP 170 glass is based on line-scan mechanism. Developed system creates information that detects and sorts kinds of defect automatically. Designed inspection technology adopts multi-vision method by slip-beam formation for the minimum of inspection time and detection algorithm is embodied in detection ability of developed system. Designed algorithm had to make good use of kernel matrix that draws up an approach to geometry. A characteristic of defects, as pin hole, substance, protrusion, are extracted from blob analysis method. Defects, as open, short, spots and et al, are distinguished by line type inspection algorithm. In experiment, we could have ensured ability of inspection that can be detected with reliability of up to 95% in about 60 seconds.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권3호
• /
• pp.18-23
• /
• 2006

The formation degree of sustain (ITO pattern) determines the quality of a PDP (Plasma Display Panel). Thus, in the present study, we attempt to detect 100% of the defects that are larger than $30{\mu}m$. Currently, the inspection method in the PDP manufacturing process is dependent upon the naked eye or a microscope in off-line mode. In this study, a prototype inspection system for PDP ITO patterned glass is developed. The developed system, which is based on a line-scan mechanism, obtains information on the defects and sorts the defects by type automatically. The developed inspection system adopts a multi-vision method using slit-beam formation for minimum inspection time and the detection algorithm is embodied in the detection ability. Characteristic defects such as pin holes, substances, and protrusions are extracted using the blob analysis method. Defects such as open, short, spots and others are distinguished by the line type inspection algorithm. It was experimentally verified that the developed inspection system can detect defects with reliability of up to 95% in about 60 seconds for the 42-inch PDP panel.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.232-239
• /
• 2006

Guided wave techniques have been used for pipeline inspection because of the long range inspection capability of guided waves. One of main concerns of these technique is how ones decide the axial interval of sensors when they are utilized for pipeline inspection. This question is related to the characteristic of cylindrical guided wave propagation, especially wave attenuation. Thus, attenuation of fundamental longitudinal guided wave propagating liquid-filled steel pipes is numerically investigated in the paper. Several liquids such as water, diesel oil, castor oil etc. are considered for the filing materials in the pipes. Sink is considered for numerical models for abandoning standing wave modes; hence, the attenuation dispersion curves become much simpler. Those attenuation calculations can be utilized for guided-wave-based nondestructive testing of pipelines when one inspects pipelines, using monitoring sensors, which are installed outside pipes.

• 대한산업공학회지
• /
• 제30권2호
• /
• pp.84-92
• /
• 2004

A process control procedure is proposed when 100% inspection is performed in a process with excellent capability. Only the incomplete measurement data is assumed to be available, i.e. the specific measurement value of the quality characteristic is not available for each item but it can be determined to be smaller or larger than any prescribed value. In the suggested model, a signal limit is introduced to determine whether the process under study is in control or not. If the quality characteristic of an incoming item exceeds the upper signal or the lower signal limit, the process is determined to be stopped or not by comparing the number of consecutively accepted items with a predetermined threshold number. The procedure is designed based on the type I and II errors. The performance of the model is evaluated by the expected number of items produced under the in-control and out-of-control states until the process is stopped.

• 한국구조물진단유지관리공학회 논문집
• /
• 제7권2호
• /
• pp.141-148
• /
• 2003

Concrete surface is a part that resists chiefly to carbonation by carbonic acid gas, affluence of rainwater and air, deterioration by freezing thawing, salt damage by seawater, and other chemical erosion etc. Therefore, this research analyzed physical characteristic and durable characteristic of concrete eliminated glut water and bubble of concrete surface using CON-SILK that is permeated with dehydration. As a research result, concrete using CON-SILK was improved, in comparison with concrete using general formwork, in physical performance and durability of concrete, as surface hardness, carbonation resistivity, and salt content permeation resistivity etc. Therefore, we could know that it is effective to use CON-SILK in performance elevation of concrete surface.

• 품질경영학회지
• /
• 제25권4호
• /
• pp.57-70
• /
• 1997

Consider a production system where all manufactured products are screened through automatic inspection equipment. The products for which the measured value of quality characteristic is larger than the lower screening specification limit (SL) and smaller than the u, pp.r screeing specification limit(SU) are accepted. Those smaller than SL are reworked and those larger than SU are excluded from the process. Assuming that the quality characteristic is normally distributed with known variance, this paper suggests cost models which involve inspection cost, production cost, rework cost, exclusion cost and quality cost, and presents the methods of finding the optimal values of the screening specification limits and the process target. Numerical example is given to demonstrate the a, pp.icability of the cost models suggested in this paper.

• 산업경영시스템학회지
• /
• 제21권47호
• /
• pp.101-112
• /
• 1998

Recently, researchers show growing interest on product quality characteristic dependence and designing acceptance sampling plans under the quality dependence. This research intends to resolve a few theoretical and practical questions for better application of acceptance sampling when the quality characteristic of product items exhibits a statistical dependence and samples are inspected according to the production order. In this research, a mathematical programming model is developed for the economic modeling of sampling plans based on two evaluation criteria : the average outgoing quality(AOQ) and the average total inspection cost. An efficient solution procedure is then proposed using the functional structure of the two evaluation criteria and the procedure is numerically illustrated.

• 경영과학
• /
• 제24권1호
• /
• pp.77-90
• /
• 2007

Taguchi assumed that a product characteristic has the uniform distribution in its preventive maintenance limit when deriving the expected loss generated by the quality deviation. But it is reasonable to assume that a product characteristic has the normal distribution than the uniform distribution. On this paper, we first find the optimum inspection interval and the optimum preventive maintenance limit under the truncated triangular distribution. Secondly we use the beta-general distribution and compare with the truncated triangular distribution. By using the numerical examples, we find the optimum inspection interval and the optimum preventive maintenance limit under their distributions. As a result, we find that the beta-general distribution gives the best solution and easy calculation.

• 대한산업공학회지
• /
• 제23권4호
• /
• pp.793-802
• /
• 1997

A sampling plan is presented for situations where sampling inspection is based on the quality characteristic of interest and items in rejected lots are screened based on a correlated variable. A cost model is constructed which involves the costs of misclassification errors, sampling and screening inspections. A method of finding optimal values of sample size, acceptance number and cutoff value on the correlated variable is presented, and numerical studies are given.