• 한국세라믹학회지
• /
• 제40권2호
• /
• pp.167-171
• /
• 2003

기계적 방법으로 합성된 CeO$_2$분말을 연마입자로 하여 STI용 CMP 슬러리를 제조하였다. 연마입자는 정전기적 방법과 입체적 방법으로 수계에서 안정화시킬 수 있었으며, 장기 안정성을 위해서는 입체적 방법에 의한 안정화가 유효하였다. 50$0^{\circ}C$와 $700^{\circ}C$에서 합성된 CeO$_2$를 이용하여 CMP 슬러리를 제조하고, SiO$_2$와 Si$_3$N$_4$가 블랭킷 형태로 증착된 웨이퍼를 연마한 결과 연마능률과 선택비는 연마입자의 합성조건과 분산 안정성, 슬러리의 pH 등에 의해 영향을 받았다.

• 한국전기전자재료학회논문지
• /
• 제18권1호
• /
• pp.12-16
• /
• 2005

Chemical mechanical polishing (CMP) process is one of the most useful methods for improving the surface roughness of films. The effects of CMP on the surface morphology of WO$_3$ films prepared by RF sputtering system were investigated in this paper. A removal rate of films increased, and the uniformity performance of surface decreased with the addition of an oxidizer to the tungsten slurry. Non-uniformity performance of surface was superior as its value was below 5 % when oxidizers of 5.0 vol% and 2.5 vol%, respectively, were added to the tungsten slurry. The optimized oxidizer concentration, reflected both the improved roughness values and hillock-free surface with the good uniformity performance, was 5.0 vol% as an atomic force microscopy(AFM) analysis of thin film topographies. Our CMP results will be a useful reference for advanced technology of thin films for gas sensor applications in the near future.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권11호
• /
• pp.551-555
• /
• 2004

In this paper, in order to reduce the high COO (cost of ownership) and COC (cost of consumables), we have collected the silica abrasive powders by filtering method after subsequent CMP (chemical mechanical polishing) process for the purpose of abrasives recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size distribution and FE-SEM (field emission-scanning electron microscope) measurements of abrasive powders. It was annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slurry. As our experimental results, we obtained the comparable rate of removal and good planarity with commercial products. Consequently we can expect the saving of high cost slurry.

• Transactions on Electrical and Electronic Materials
• /
• 제5권6호
• /
• pp.233-236
• /
• 2004

Copper metallization has been used in high-speed logic ULSI devices instead of the conventional aluminum alloy metallization. One of the key issues in copper CMP is the development of slurries that can provide high removal rates. In this study, the effects of slurry chemicals and pH for slurry dispersion stability on Cu CMP process characteristics have been performed. The experiments of copper slurries containing each different alumina and colloidal silica particles were evaluated for their selectivity of copper to TaN and $SiO_{2}$ films. Furthermore, the stability of copper slurries and pH are important parameters in many industries due to problems that can arise as a result of particle settling. So, it was also observed about several variables with various pH.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.87-88
• /
• 2006

To investigate the possibility of ceria abrasive-added slurry for the oxide-chemical mechanical polishing (oxide-CMP) application, two kinds of retreated methods were introduced as follows: First, the characteristics of mixed abrasive slurry (MAS) using $CeO_2$ powder as an abrasive added within diluted silica slurry (DSS) were evaluated to achieve the improvement of removal rates and non-uniformity. Second, the control of pH level due to the dilution of slurry was examined. And then, we have discussed the CMP characteristics as a function of abrasive dispersion time.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.185-188
• /
• 2001

Chemical mechanical polishing(CMP) process is widely used for global planarization of inter-metal dielectric (IMD) layer and inter-layer dielectric (ILD) for deep sub-micron technology. However, as the IMD and ILD layer gets thinner, defects such as micro-scratch lead to severe circuit failure, which affect yield. In this paper, for the improvement of CMP process, deionized water (DIW) pressure, purified $N_2 \; (PN_2)$ gas, slurry filter and high spray bar were installed. Our experimental results show that DIW pressure and $PN_2$ gas factors were not related with removal rate, but edge hot-spot of patterned wafer had a serious relation. Also, the filter installation in CMP polisher could reduce defects after CMP process, it is shown that slurry filter plays an important role in determining consumable pad lifetime. The filter lifetime is dominated by the defects. However, the slurry filter is impossible to prevent defect-causing particles perfectly. Thus, we suggest that it is necessary to install the high spray bar of de-ionized water (DIW) with high pressure, to overcome the weak-point of slurry filter. Finally, we could expect the improvements of throughput, yield and stability in the ULSI fabrication process.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권5호
• /
• pp.191-195
• /
• 2002

Chemical mechanical Polishing (CMP) process is widely used for the global planarization of inter-metal dielectric (IMD) layer and inter-layer dielectric (ILD) for deep sub-micron technology. However, as the IMD and ILD layer gets thinner, defects such as micro-scratch lead to severe circuit failure, which affect yield. In this paper, for the improvement of CMP process, deionized water (DIW) pressure, purified $N_2$ ($PN_2$) gas, point of use (POU) slurry filler and high spray bar (HSB) were installed. Our experimental results show that DW pressure and P$N_2$ gas factors were not related with removal rate, but edge hot-spot of patterned wafer had a serious relation. Also, the filter installation in CMP polisher could reduce defects after CMP process, it is shown that slurry filter plays an important role in determining consumable pad lifetime. The filter lifetime is dominated by the defects. However, the slurry filter is impossible to prevent defect-causing particles perfectly. Thus, we suggest that it is necessary to install the high spray bar of de-ionized water (DIW) with high pressure, to overcome the weak-point of slurry filter Finally, we could expect the improvements of throughput, yield and stability in the ULSI fabrication process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.145-148
• /
• 2003

Recently, the recycle of CMP (chemical mechanical polishing) slurries have been positively considered in order to reduce the high COO (cost of ownership) and COC (cost of consumables) in CMP process. Among the composition of slurries (buffer solution, bulk solution, abrasive particle, oxidizer, inhibitor, suspension, antifoaming agent, dispersion agent), the abrasive particles are one of the most important components. Especially, the abrasive particles of slurry are needed in order to achieve a good removal rate. However, the cost of abrasives, is still very high. In this paper, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size and hardness. Also, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slury, As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• 한국전기전자재료학회논문지
• /
• 제20권1호
• /
• pp.74-79
• /
• 2007

Most studies on copper Chemical Mechanical Planarization (CMP) have focused on material removal and its mechanisms. Although many studies have been conducted on the mechanism of Cu CMP, a study on uniformity in Cu CMP is still unknown. Since the aim of CMP is global and local planarization, the approach to various factors related to uniformity in Cu CMP is essential to elucidate the Cu CMP mechanism as well. The main purpose of the experiment reported here was to investigate and mechanically analyze the roles of slurry components in the formation of the uniformity in Cu CMP. In this paper, Cu CMP was performed using citric acid($C_{6}H_{8}O_{7}$), hydrogen peroxide($H_{2}O_{2}$), colloidal silica, and benzotriazole($BTA,\;C_{6}H_{4}N_{3}H$) as a complexing agent, an oxidizer, an abrasive, and a corrosion inhibitor, respectively. All the results of this study showed that within-wafer non-uniformity(WIWNU) of Cu CMP could be controlled by the contents of slurry components.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2005년도 춘계학술발표대회 및 제8회 신소재 심포지엄 논문개요집
• /
• pp.251-251
• /
• 2005