• Transactions on Electrical and Electronic Materials
• /
• v.1 no.1
• /
• pp.40-44
• /
• 2000

Metal-ferroelectric-insulator-semoiconductor field effect transistor (MFISFETs) were fabricated using CMOS processes. The Pt/SBT/NO combined layers were etched for forming a conformal gate by using Ti/Cr metal masks and a two step etching method, By the method, we were able to fabricate a small-sized gate with the dimension of $16/4{\mu}textrm{m}$ in the width/length of gate. It has been chosen the non-self aligned source and drain implantation process, We have deposited inter-layer dielectrics(ILD) by low pressure chemical vapor deposition(LPCVD) at $380^{circ}C$ after etching the gate structure and the threshold voltage of p-channel MFISFETs were about 1.0 and -2.1V, respectively. It was also observed that the current difference between the $I_{ON}$(on current) and $I_{OFF}$(off current) that is very important in sensing margin, is more that 100 times in $I_{D}-V_{G}$ hysteresis curve.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.4
• /
• pp.43-53
• /
• 2002

In this paper, a new dynamic D-flip-flop which does not suffer from charge sharing and glitch problems is proposed. And a dual-modulus divide-by-128/129 prescaler has been designed with the proposed D-flip-flops using a 0.6$0.6{\mu}m$ CMOS technology. Eleven-transistor architecture enables it to operate at the higher frequency range and the transistor merging technique contributes to the reduction of power consumption. At 5V supply voltage, the simulated maximum operating frequency and the current consumption of the divide-by-128/129 prescaler are 1.97GHz and 7.453mA, respectively.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.146-153
• /
• 2008

Integrated humidity sensor system with two stages operational amplifier has been designed and fabricated by $0.8{\mu}m$ analog mixed CMOS technology. The system (28 pin and $2mm{\times}4mm$) consisted of Wheatstone-bridge type humidity sensor, resistive type humidity sensor, temperature sensors and operational amplifier for signal amplification and process in one chip. The poly-nitride etch stop process has been tried to form the sensing area as well as trench in a standard CMOS process. This modified technique did not affect the CMOS devices in their essential characteristics and gave an allowance to fabricate the system on same chip by standard process. The operational amplifier showed the stable operation so that unity gain bandwidth was more than 5.46 MHz and slew rate was more than 10 V/uS, respectively. The drain current of n-channel humidity sensitive field effect transistor (HUSFET) increased from 0.54 mA to 0.68 mA as the relative humidity increased from 10 to 70 %RH.

• ETRI Journal
• /
• v.34 no.6
• /
• pp.950-953
• /
• 2012

Schottky barrier single electron transistors (SB-SETs) and Schottky barrier single hole transistors (SB-SHTs) are fabricated on a 20-nm thin silicon-on-insulator substrate incorporating e-beam lithography and a conventional CMOS process technique. Erbium- and platinum-silicide are used as the source and drain material for the SB-SET and SB-SHT, respectively. The manufactured SB-SET and SB-SHT show typical transistor behavior at room temperature with a high drive current of $550{\mu}A/{\mu}m$ and $-376{\mu}A/{\mu}m$, respectively. At 7 K, these devices show SET and SHT characteristics. For the SB-SHT case, the oscillation period is 0.22 V, and the estimated quantum dot size is 16.8 nm. The transconductance is $0.05{\mu}S$ and $1.2{\mu}S$ for the SB-SET and SB-SHT, respectively. In the SB-SET and SB-SHT, a high transconductance can be easily achieved as the silicided electrode eliminates a parasitic resistance. Moreover, the SB-SET and SB-SHT can be operated as a conventional field-effect transistor (FET) and SET/SHT depending on the bias conditions, which is very promising for SET/FET hybrid applications. This work is the first report on the successful operations of SET/SHT in Schottky barrier devices.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1188-1198
• /
• 2015

In this paper, a multi-time programmable (MTP) cell based on a $0.18{\mu}m$ bipolar-CMOS-DMOS backbone process that can be written into by using dual pumping voltages - VPP (boosted voltage) and VNN (negative voltage) - is used to design MTP memories without high voltage devices. The used MTP cell consists of a control gate (CG) capacitor, a TG_SENSE transistor, and a select transistor. To reduce the MTP cell size, the tunnel gate (TG) oxide and sense transistor are merged into a single TG_SENSE transistor; only two p-wells are used - one for the TG_SENSE and sense transistors and the other for the CG capacitor; moreover, only one deep n-well is used for the 256-bit MTP cell array. In addition, a three-stage voltage level translator, a VNN charge pump, and a VNN precharge circuit are newly proposed to secure the reliability of 5 V devices. Also, a dual memory structure, which is separated into a designer memory area of $1row{\times}64columns$ and a user memory area of $3rows{\times}64columns$, is newly proposed in this paper.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.497-505
• /
• 2016

The two-dimensional (2D) Discrete Cosine Transform (DCT) is used widely in image and video processing systems. The perception of human visualization permits us to design approximate rather than exact DCT. In this paper, we propose a digital implementation of 16-point approximate 2D DCT architecture based on one-dimensional (1D) DCT and Modified Gate Diffusion Input (MGDI) technique. The 8-point 1D Approximate DCT architecture requires only 12 additions for realization in digital VLSI. Additions can be performed using the proposed 8 transistor (8T) MGDI Full Adder which reduces 2 transistors than the existing 10 transistor (10T) MGDI Full Adder. The Approximate MGDI 2D DCT using 8T MGDI Full adders is simulated in Tanner SPICE for $0.18{\mu}m$ CMOS process technology at 100MHZ.The simulation result shows that 13.9% of area and 15.08 % of power is reduced in the 8-point approximate 2D DCT, 10.63 % of area and 15.48% of power is reduced in case of 16-point approximate 2D DCT using 8 Transistor MGDI Full Adder than 10 Transistor MGDI Full Adder. The proposed architecture enhances results in terms of hardware complexity, regularity and modularity with a little compromise in accuracy.

• The KIPS Transactions:PartA
• /
• v.14A no.4
• /
• pp.203-208
• /
• 2007

This paper proposes a $64{\times}64$ Modified Booth multiplier using CMOS multi-valued logic circuits. The multiplier based on the radix-4 algorithm is designed with current mode CMOS quaternary logic circuits. Designed multiplier is reduced the transistor count by 64.4% compared with the voltage mode binary multiplier. The multiplier is designed with Samsung $0.35{\mu}m$ standard CMOS process at a 3.3V supply voltage and unit current $5{\mu}m$. The validity and effectiveness are verified through the HSPICE simulation. The voltage mode binary multiplier is achieved the occupied area of $7.5{\times}9.4mm^2$, the maximum propagation delay time of 9.8ns and the average power consumption of 45.2mW. This multiplier is achieved the maximum propagation delay time of 11.9ns and the average power consumption of 49.7mW. The designed multiplier is reduced the occupied area by 42.5% compared with the voltage mode binary multiplier.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.788-791
• /
• 2010

We design 64-bit ROM IP for RFID tag chips using printed CMOS non-volatile memory IP design technology for a printed CMOS process. The proposed 64-bit ROM circuit is using ETRI's $0.8{\mu}m$ CMOS porocess, and is expected to reduce process complexity and cost of RFID tag chips compared to that using a conventional silicon fabrication based on a complex lithography process because the poly layer in a gate terminal is using printing technology of imprint process. And a BL precharge circuit and a BL sense amplifier is not required for the designed cell circuit since it is composed of a transmission gate instead of an NMOS transistor of the conventional ROM circuit. Therefore an output datum is only driven by a DOUT buffer circuit. The Operation current and layout area of the designed ROM of 64 bits with an array of 8 rows and 8 columns using $0.8{\mu}m$ ROM process is $9.86{\mu}A$ and $379.6{\times}418.7{\mu}m^2$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.8
• /
• pp.1227-1234
• /
• 2013

An analog array with a 1.2 double poly floating gate transistor has been developed with a standard CMOS fabrication process. The programming of each cell by means of an efficient control circuit eliminates the unnecessary erasing operation which has been widely used in conventional analog memories. It is seen that the path of the signal for both the programming and the reading is almost exactly the same since just one comparator supports both operations. It helps to eliminate the effects of the amplifier input-offset voltage problem on the output voltage for the read operation. In the array, there is no pass transistor isolating a cell of interest from the adjacent cells in the array. Instead of the extra transistors, one extra bias voltage, Vmid, is employed. The experimental results from the memory shows that the resolution of the memory is equivalent to the information content of at least six digital cells. Programming/erasing of each cell is achieved with no detectable disturbance of adjacent cells. Finally, the unique shape of the injector structure in a EEPROM is adopted as a cell of analog array. It reduces the programming voltage below the transistor breakdown voltage without any special fabrication process.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.38 no.2
• /
• pp.38-49
• /
• 2001

This paper presents a new voltage down converter(VDC) using charge and discharge current adjustment circuitry that provides high frequency application. This VDC consist of a common driving circuit and compensation circuits: 2 sensors and each driving transistors for controlling gate current of driving transistor. These sensors are operated as adaptive biasing method with high speed and low power consumption. This circuit is designed with a $0.62{\mu}m$ N well CMOS technology. In H-spice simulation results, internal voltage is bounded ( IV, +0.6V) in proposed circuitry when load current rapidly increases and decreases during Gns between 0 and $200m{\Lambda}$. And the recovery time of internal voltage is about 7ns and 10ns when load current increases and decreases respectively. That is fast better than common driving circuit. Total power consumption is about 1.2mW.