• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.82-85
• /
• 2004

This paper proposes an advanced circuit for the capacitive type fingerprint sensor signal processing and an effective isolation structure for minimizing an electrostatic discharge(ESD) influence and for removing a signal coupling noise of each sensor pixel. The proposed detection circuit increases the voltage difference between a ridge and valley about $80\%$ more than old circuit. The test chip is composed of $160\;\times\;192$ array sensing cells $(9,913\times11,666\;um^2).$ The sensor plate area is $58\;\times\;58\;um^2$ and the pitch is 60um. The image resolution is 423 dpi. The chip was fabricated on a 0.35um standard CMOS process. It successfully captured a high-quality fingerprint image and performed the registration and identification processing. The sensing and authentication time is 1 sec(.) with the average power consumption of 10 mW at 3.0V. The reveal ESD tolerance is obtained at the value of 4.5 kV.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.507-508
• /
• 2006

High performance delta-sigma modulator is developed for audio-codec applications(i.e.. 16-bit resolution at a 20kHz signal bandwidth). The modulator is realized with fully-differential switched capacitor integrators. All stages employ a single-stage folded-cascode amplifier. The presented delta-sigma modulator when clocked at 3.2MHz achieves 85.2dB peak-SNDR and 94.8dB SNR. This modulator is designed in a SAMSUNG $0.18{\mu}m$ CMOS process. Finally, this paper shows the test setup and FFT result gained from delta-sigma modulator chip designed for audio applications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.1
• /
• pp.22-28
• /
• 2009

This paper presents a fast received signal strength indicator (RSSI) circuit for wireless communication application. The proposed circuit is developed using power detectors and an analog-to-digital converter to achieve a fast settling time. The power detector is consisted of a novel logarithmic variable gain amplifier (VGA), a peak detector, and a comparator in a closed loop. The VGA achieved a wide logarithmic gain range in a closed loop form for stable operation. For the peak detector, a fast settling time and small ripple are obtained using the orthogonal characteristics of quadrature signals. In $0.18-{\mu}m$ CMOS process, the RSSI value settles down in $20{\mu}s$ with power consumption of 20 mW, and the maximum ripple of the RSSI is 30 mV. The proposed RSSI circuit is fabricated with a personal handy-phone system transceiver. The active area is $0.8{\times}0.2\;mm^2$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.96-104
• /
• 2007

In this paper, the field solver based deembedding technique for the on-chip inductors to deembed the pad and surrounding ground effect was described, and the results from field solver based deembedding techniques and measurement based matrix calculation method were compared. In addition, LNA circuit is designed by using deembedded inductors and fabricated by using standard $0.25{\mu}m$ CMOS process, in the range over the 2.5GHz it shows the good agreements between measurement and simulation results when the proper deembedding was adapted. Supposed deembedding techniques can be used to get the pure on-chip devices's values and adapted to design accurate RFIC circuit design.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.497-505
• /
• 2016

The two-dimensional (2D) Discrete Cosine Transform (DCT) is used widely in image and video processing systems. The perception of human visualization permits us to design approximate rather than exact DCT. In this paper, we propose a digital implementation of 16-point approximate 2D DCT architecture based on one-dimensional (1D) DCT and Modified Gate Diffusion Input (MGDI) technique. The 8-point 1D Approximate DCT architecture requires only 12 additions for realization in digital VLSI. Additions can be performed using the proposed 8 transistor (8T) MGDI Full Adder which reduces 2 transistors than the existing 10 transistor (10T) MGDI Full Adder. The Approximate MGDI 2D DCT using 8T MGDI Full adders is simulated in Tanner SPICE for $0.18{\mu}m$ CMOS process technology at 100MHZ.The simulation result shows that 13.9% of area and 15.08 % of power is reduced in the 8-point approximate 2D DCT, 10.63 % of area and 15.48% of power is reduced in case of 16-point approximate 2D DCT using 8 Transistor MGDI Full Adder than 10 Transistor MGDI Full Adder. The proposed architecture enhances results in terms of hardware complexity, regularity and modularity with a little compromise in accuracy.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.255-260
• /
• 2016

In this paper, a full-wave rectifier (FWR) with a simple vibration detector suitable for use with vibrational energy harvesting systems is presented. Conventional active FWRs where active diodes are used to reduce the diode voltage drop and increase the system efficiency are usually powered from the output. Output-powered FWRs exhibit relatively high efficiencies because the comparators used in active diodes are powered from the stable output voltage. Nevertheless, a major drawback is that these FWRs consume power from the output storage capacitor even when the system is not harvesting any energy. To overcome the problem, a technique using a simple vibration detector consisting of a peak detector and a level converter is proposed. The vibration detector detects whether vibrational energy exists or not in the input terminal and disables the comparators when there is no vibrational energy. The proposed FWR with the vibration detector is designed using a $0.35-{\mu}m$ CMOS process. Simulation results have verified the effectiveness of the proposed scheme. By using the proposed vibration detector, a decrease in leakage current by approximately 67,000 times can be achieved after the vibration disappears.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.387-394
• /
• 2016

This paper presents a fully digital delay locked loop (DLL) that can acquire lock in four clock cycles with a resolution of a 1/4 NAND-delay. The proposed DLL with a multi-dither-free phase detector acquires the initial lock in four clock cycles with 1/2 NAND-delay. Then, it utilizes a multi-dither-free phase detector, a region accumulator, and phase blenders, to improve the resolution to a 1/4 NAND-delay. The region accumulator which continuously steers the control registers and the phase blender, adaptively controls the tracking bandwidth depending on the amount of jitter, and effectively suppresses the dithering jitter. Fabricated in a 65 nm CMOS process, the proposed DLL occupies $0.0432mm^2$, and consumes 3.7 mW from a 1.2-V supply at 2 GHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.295-301
• /
• 2011

A triple-band transceiver module for 2.3/2.5/3.5 GHz mobile WiMAX, IEEE 802.16e, applications is introduced. The suggested transceiver module consists of RFIC, reconfigurable/multi-resonance MIMO antenna, embedded PCB, mobile WiMAX base band, memory and channel selection front-end module. The RFIC is fabricated in $0.13{\mu}m$ RF CMOS process and has 3.5 dB noise figure(NF) of receiver and 1 dBm maximum power of transmitter with 68-pin QFN package, $8{\times}8\;mm^2$ area. The area reduction of transceiver module is achieved by using embedded PCB which decreases area by 9% of the area of transceiver module with normal PCB. The developed triple-band mobile WiMAX transceiver module is tested by performing radio conformance test(RCT) and measuring carrier to interference plus noise ratio (CINR) and received signal strength indication (RSSI) in each 2.3/2.5/3.5 GHz frequency.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.32-36
• /
• 2003

In this work, we have designed a fully integrated 2.4GHz LC-tuned voltage-controlled oscillator (VCO) with multiple tuning inputs for a 0.25-$\mu\textrm{m}$ standard CMOS process. The design of voltage-controlled oscillator is based on an LC-resonator with a spiral inductor of octagonal type and pMOS-varactors. Only two metal layer have been used in the designed inductor. The frequency tuning is achieved by using parallel pMOS transistors as varactors and back-gate tuned pMOS transistors in an active region. Coarse tuning is achieved by using 3-bit pMOS-varactors and fine tuning is performed by using back-gate tuned pMOS transistors in the active region. When 3-bit digital and analog inputs are applied to the designed circuits, voltage-controlled oscillator shows the tuning feature of frequency range between 2.3 GHz and 2.64 GHz. At the power supply voltage of 2.5 V, phase noise is -128dBc/Hz at 3MHz offset from the carrier. Total power dissipation is 7.5 mW.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.775-777
• /
• 2016

In this paper presents an analysis of pulsed radiation effects of unit devices. Unit devices are the nMOSFET, pMOSFET, NPN Transistor and those fabricated by the 0.18um CMOS process. Pulsed radiation test results in nMOSFET, the photocurrent of tens nA was generated in $2.07{\times}10^8rad(si)/s$. For the pMOSFET, a photocurrent generation was not observed in $3{\times}10^8rad(si)/s$. For the NPN transistor, the photocurrent was generated with about 1uA. Therefore, the MOSFET must be used than BJT transistor when radhard IC design.