• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.11
• /
• pp.149-156
• /
• 2012

A digital input class-D audio amplifier is presented for digital hearing aid. The class-D audio amplifier is composed of digital and analog circuits. The analog circuit converts a digital input to a analog audio signal (DAC) with noise suppression in the audio band. An interpolated digital delta-sigma modulator is used to convert data types between digital signal processor (DSP) and digital-to-analog converter (DAC). An 16-bit, 25-kbps pulse code modulated (PCM) input is interpolated to 16-bit, 50-kbps by a digital filter. The output signal of interpolation filter is noise-shaped by a third-order digital sigma-delta modulator (SDM). As a result, 1.5-bit, 3.2-Mbps signal is applied to simple digital to analog converter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.1
• /
• pp.129-134
• /
• 2014

This paper presents a 10-bit 10-MS/s asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) which consists of a digital-to-analog converter (DAC), a SAR logic, and a comparator. The designed asynchronous SAR ADC with a rail-to-rail input range uses a binary weighted DAC using metal-oxide-metal (MOM) capacitor to improve sampling rate. The proposed 10-bit 10-MS/s asynchronous SAR ADC is fabricated using a 0.18-${\mu}m$ CMOS process and its active area is $0.103mm^2$. The power consumption is 0.37 mW when the voltage of supply is 1.1 V. The measured SNDR are 54.19 dB and 51.59 dB at the analog input frequency of 101.12 kHz and 5.12 MHz, respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.8-12
• /
• 2002

Since the high performance analog-to-digital converter can be built with Rapid Single Flux Quantum (RSFQ) logic circuits the development of superconductive analog-to-digital converter has attracted a lot of interests as one of the most prospective area of the application of Josephson Junction technology. One of the main advantages in using Rapid Sng1e Flux Quantum logic in the analog-to-digital converter is the low voltage output from the Josephson junction switching, and hence the high resolution. To design an analog-digital converter, first we have used XIC tool to compose a circuit schematic, and then studied the operational principle of the circuit with WRSPICE tool. Through this process, we obtained the proper circuit diagram of an 1-bit analog-digital converter circuit. The optimized circuit was laid out as a mask drawing. Inductance values of the circuit layout were calculated with L-meter.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.1
• /
• pp.33-41
• /
• 2019

We propose an embedded solution to design a high-speed and high-accuracy 16bit analog-digital signal processing interface for the control systems using various external analog signals. Choosing TMS320F28377D micro controller unit (MCU) featuring high-performance processing in the 32-bit floating point operation, low power consumption, and various I/O device supports, we design and build the proposed system that supports both 16-bit analog-digital converter (ADC) interface and high precision digital-analog converter (DAC) interface. The ADC receives voltage-level differential signals from fully differential amplifiers, and the DAC communicates with MCU through 50 MHz bandwidth high-fast serial peripheral interface (SPI). We port the boot loader and device drivers to the implemented board, and construct the firmware development environment for the application programming. The performance of the entire implemented system is demonstrated by analog-digital signal processing tests, and is verified by comparing the test results with those of existing similar systems.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1166-1169
• /
• 1987

A new analog-la-digital structure. called cyclic-parallel analog-to-digital(A/D) converter, has been developed for video applications. It consists of a M-bit parallel A/D converter, a digital-to-analog(D/A) converter, a differencing amplifier with gain of $2^M$ and two sample-and-hold circuits. In this structure, the input signal is circulated around the circuits K times, thereby converted into a MK-bit digital word. The proposed converter retains speed advantages of conventional series-parallel converters, with half reduced circuit components.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.847-850
• /
• 1998

One of the most difficult problem of designing VLSI is a mixed-circuit design, that is to design circuit containing both analog parts and digital parts. Digital to analog converter and analog to digital converter is a typical case. Especially it can be a serious problem when mixed circuit are put into a large digital circuit like microcontroller. However nowadays this problem is settled by separating analog circuit parts outside the IC. This technique is based on converting a digital signal into a pulse sequence. Then an analog signal is obtained by averaging this pulse sequence at the external low-pass filter. An anlog to digital converter is designed using a stochastic logic instead of a traditional PWM (pulse-width modulation) signal and ins implemente dusing FPGa. Stochastic pulse sequence can be made as a simple circuits and moreover can be mathematically processed by simple circuits -AND gates. The spectral property of stochastic pulse sequence method is better than that of PWM method. So it make easy to design a external low-pass filter. This technique has important advantages, especially the reduction of the ADC cost.

• The Magazine of the IEIE
• /
• v.2 no.2
• /
• pp.37-42
• /
• 1975

Various factors which affect the linearity and accuracy of the ramp type analog-to-digital converter have been investigated experimentally. A suggestion hav been made in the determination of circuit parameters with the emphasis on the improvement of the linearity and accuracy in the ramp type analog-to-digital conveter.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.522-527
• /
• 1987

This paper describes the hardware of analog-to-digital converter to process the rate output of analog servo loop for the gyro rebalance of INS. The analog-to-digital converter is designed by voltage-to-frequency method which is generally used in INS, and this scheme fits well into the strapdown INS that requires the wide dynamic range and linearity. The output of the designed voltage to frequency converter is tested by computer through the counter and all the factors which affect the performance are considered.

• Journal of the Korea Society for Simulation
• /
• v.11 no.2
• /
• pp.17-29
• /
• 2002

There is an increasing interest in high-performance A/D(Analog-to-Digital) converters for use in integrated analog and digital mixed processing systems. Pipeline A/D converter architectures coupled with BiCMOS process technology have the potential for realizing monolithic high-speed and high-accuracy A/D converters. In this paper, the design of 12bit pipeline BiCMOS A/D converter presented. A BiCMOS operational amplifier and comparator suitable for use in the pipeline A/D converter. Test/simulation results of the circuit blocks and the converter system are presented. The main features is low distortion track-and-hold with 0-300MHz input bandwidth, and a proprietary 12bit multi-stage quantizer. Measured value is DNL=${\pm}$0.30LSB, INL=${\pm}$0.52LSB, SNR=66dBFS and SFDR=74dBc at Fin=24.5MHz. Also Fabricated on 0.8um BiCMOS process.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.7
• /
• pp.42-48
• /
• 1994

In this paper, a low power and high speed flash Analog-to-Digital Converter using current-mode concept is proposed. Current-mode approach offers a number of advantages over conventional voltage-mode approach, such as lower power consumption small chip area improved accuracy etc. Rescently this concept was applied to algorithmic A/D Converter. But, its conversion speed is limited to medium speed. Consequently this converter is not applicable to the high speed signal processing system. This ADC is fabricated in 1.2um double metal CMOS standard process. This ADC's conversion time is measured to be 7MHz, and power consumption is 2.0mW, and differential nonlinearity is less than 1.14LSB and total harmonic distortion is -50dB. The active area of analog chip is about 350 x 550u$m^2$. The proposed ADC seems suitable for a single chip design of digital signal processing system required high conversion speed, high resolution small chip area and low power consumption.