• 전자공학회논문지
• /
• 제49권11호
• /
• pp.149-156
• /
• 2012

디지털 입력 D급 증폭기는 보청기에서 사용되고 있으며 D급 증폭기는 디지털 회로와 아날로그 회로로 구성되어진다. 아날로그 회로는 가청 주파수 대역에서 잡음을 억제하고 디지털 입력을 아날로그 신호로 변환한다. 본 논문에서 제안한 인터폴레이티드 디지털 델타-시그마 변조기는 디지털 신호 처리기의 출력 신호를 D/A 변조기 입력에 적합하도록 데이터를 변조시킨다. 디지털 필터는 16-bit, 25-kbps 펄스 코드 변조 신호를 16-bit, 50-kbps 신호로 보간 작업을 한다. 이 보간 필터 출력은 3차 디지털 델타-시그마 변조기를 통하여 노이즈 쉐이핑(noise shaping) 처리된다. 최종적으로, 1.5-bit, 3.2-Mbps 신호가 D/A 변조기 입력으로 인가된다.

• 한국정보통신학회논문지
• /
• 제18권1호
• /
• pp.129-134
• /
• 2014

본 논문은 디지털-아날로그 변환기(DAC: digital-to-analog converter), SAR 로직, 그리고 비교기로 구성된 10-bit 10-MS/s 비동기 축차근사형(SAR: successive approximation register) 아날로그-디지털 변환기(ADC: analog-to-digital converter)를 제안한다. Rail-to-rail의 입력 범위를 가지는 설계된 비동기 축차근사형 아날로그-디지털 변환기는 샘플링 속도를 향상시키기 위해 MOM(metal-oxide-metal) 커패시터를 이용한 바이너리 가중치 기반의 디지털-아날로그 변환기를 사용하여 구현한다. 제안하는 10-bit 10-MS/s 비동기 축차근사형 아날로그-디지털 변환기는 0.18-${\mu}m$ CMOS 공정에서 제작되고 면적은 $0.103mm^2$를 차지한다. 1.1 V의 공급전압에서 전력소모는 0.37 mW를 나타낸다. 101.12 kHz와 5.12 MHz의 아날로그 입력 신호에 대해 측정된 SNDR은 각각 54.19 dB와 51.59 dB이다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권1호
• /
• pp.8-12
• /
• 2002

Since the high performance analog-to-digital converter can be built with Rapid Single Flux Quantum (RSFQ) logic circuits the development of superconductive analog-to-digital converter has attracted a lot of interests as one of the most prospective area of the application of Josephson Junction technology. One of the main advantages in using Rapid Sng1e Flux Quantum logic in the analog-to-digital converter is the low voltage output from the Josephson junction switching, and hence the high resolution. To design an analog-digital converter, first we have used XIC tool to compose a circuit schematic, and then studied the operational principle of the circuit with WRSPICE tool. Through this process, we obtained the proper circuit diagram of an 1-bit analog-digital converter circuit. The optimized circuit was laid out as a mask drawing. Inductance values of the circuit layout were calculated with L-meter.

• 대한임베디드공학회논문지
• /
• 제14권1호
• /
• pp.33-41
• /
• 2019

We propose an embedded solution to design a high-speed and high-accuracy 16bit analog-digital signal processing interface for the control systems using various external analog signals. Choosing TMS320F28377D micro controller unit (MCU) featuring high-performance processing in the 32-bit floating point operation, low power consumption, and various I/O device supports, we design and build the proposed system that supports both 16-bit analog-digital converter (ADC) interface and high precision digital-analog converter (DAC) interface. The ADC receives voltage-level differential signals from fully differential amplifiers, and the DAC communicates with MCU through 50 MHz bandwidth high-fast serial peripheral interface (SPI). We port the boot loader and device drivers to the implemented board, and construct the firmware development environment for the application programming. The performance of the entire implemented system is demonstrated by analog-digital signal processing tests, and is verified by comparing the test results with those of existing similar systems.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(II)
• /
• pp.1166-1169
• /
• 1987

A new analog-la-digital structure. called cyclic-parallel analog-to-digital(A/D) converter, has been developed for video applications. It consists of a M-bit parallel A/D converter, a digital-to-analog(D/A) converter, a differencing amplifier with gain of $2^M$ and two sample-and-hold circuits. In this structure, the input signal is circulated around the circuits K times, thereby converted into a MK-bit digital word. The proposed converter retains speed advantages of conventional series-parallel converters, with half reduced circuit components.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.847-850
• /
• 1998

One of the most difficult problem of designing VLSI is a mixed-circuit design, that is to design circuit containing both analog parts and digital parts. Digital to analog converter and analog to digital converter is a typical case. Especially it can be a serious problem when mixed circuit are put into a large digital circuit like microcontroller. However nowadays this problem is settled by separating analog circuit parts outside the IC. This technique is based on converting a digital signal into a pulse sequence. Then an analog signal is obtained by averaging this pulse sequence at the external low-pass filter. An anlog to digital converter is designed using a stochastic logic instead of a traditional PWM (pulse-width modulation) signal and ins implemente dusing FPGa. Stochastic pulse sequence can be made as a simple circuits and moreover can be mathematically processed by simple circuits -AND gates. The spectral property of stochastic pulse sequence method is better than that of PWM method. So it make easy to design a external low-pass filter. This technique has important advantages, especially the reduction of the ADC cost.

• 전자공학회지
• /
• 제2권2호
• /
• pp.37-42
• /
• 1975

램프형 A/D 변환기의 직선도의 정밀도에 영향을 미치는 여러 가지 원인들을 실험적으로 고찰하였다. 아울러 램프형 A/D 변환기의 직선도, 정밀도, 및 상계오차를 개선하기 위한 회로소자의 결정방법을 제안하였다. Various factors which affect the linearity and accuracy of the ramp type analog-to-digital converter have been investigated experimentally. A suggestion hav been made in the determination of circuit parameters with the emphasis on the improvement of the linearity and accuracy in the ramp type analog-to-digital conveter.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.522-527
• /
• 1987

This paper describes the hardware of analog-to-digital converter to process the rate output of analog servo loop for the gyro rebalance of INS. The analog-to-digital converter is designed by voltage-to-frequency method which is generally used in INS, and this scheme fits well into the strapdown INS that requires the wide dynamic range and linearity. The output of the designed voltage to frequency converter is tested by computer through the counter and all the factors which affect the performance are considered.

• 한국시뮬레이션학회논문지
• /
• 제11권2호
• /
• pp.17-29
• /
• 2002

There is an increasing interest in high-performance A/D(Analog-to-Digital) converters for use in integrated analog and digital mixed processing systems. Pipeline A/D converter architectures coupled with BiCMOS process technology have the potential for realizing monolithic high-speed and high-accuracy A/D converters. In this paper, the design of 12bit pipeline BiCMOS A/D converter presented. A BiCMOS operational amplifier and comparator suitable for use in the pipeline A/D converter. Test/simulation results of the circuit blocks and the converter system are presented. The main features is low distortion track-and-hold with 0-300MHz input bandwidth, and a proprietary 12bit multi-stage quantizer. Measured value is DNL=${\pm}$0.30LSB, INL=${\pm}$0.52LSB, SNR=66dBFS and SFDR=74dBc at Fin=24.5MHz. Also Fabricated on 0.8um BiCMOS process.

• 전자공학회논문지B
• /
• 제31B권7호
• /
• pp.42-48
• /
• 1994

In this paper, a low power and high speed flash Analog-to-Digital Converter using current-mode concept is proposed. Current-mode approach offers a number of advantages over conventional voltage-mode approach, such as lower power consumption small chip area improved accuracy etc. Rescently this concept was applied to algorithmic A/D Converter. But, its conversion speed is limited to medium speed. Consequently this converter is not applicable to the high speed signal processing system. This ADC is fabricated in 1.2um double metal CMOS standard process. This ADC's conversion time is measured to be 7MHz, and power consumption is 2.0mW, and differential nonlinearity is less than 1.14LSB and total harmonic distortion is -50dB. The active area of analog chip is about 350 x 550u$m^2$. The proposed ADC seems suitable for a single chip design of digital signal processing system required high conversion speed, high resolution small chip area and low power consumption.