• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.2
• /
• pp.306-310
• /
• 2010

On account of small size and light weight, a high-speed machine is regarded as a key technology for many future applications of drive systems. In high-speed applications, permanent magnet synchronous motors have a number of merits such as high efficiency and high power density. Therefore, they are suitable for driving the air-blower of a fuel cell electric vehicle (FCEV) where space and energy savings are critical. Particularly, a surface-mounted permanent magnet synchronous motor (SPMSM) of them is mainly used as a high-speed machine. However, the motor has a fatal flaw due to a retaining can to maintain the mechanical integrity of a rotor assembly. The can results in the increase of magnetic air-gap length in the SPMSM. Thus, in this paper, an interior permanent magnet synchronous motor (IPMSM) is applied in order to drive the air-blower of FCEV instead of the SPMSM, and the experimental results of two models are compared to verify the capability of the IPMSM for high-speed applications.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.3
• /
• pp.165-171
• /
• 2000

This paper proposes a technique to design of air-core type Linear DC Motor(LDM) by using Equivalent Magnetizing Current(EMC) method and has performed its dynamic analysis. The magnetic flux density differ in accordance with airgap position due to difference of mechanical and magnetic air gap length and the coil shape has an influence on the thrust. Therefore, the analysis of magnetic field due to the magnets is carried out by EMC. The phenomena according to the various coil various coil shape under the same Magneto Motive Force(MMF) has been analyzed and its result is applied to the design process. The appropriateness of the proposed technique is confirmed by Finite Element Method(FEM) and its dynamic analysis is carried out from the coupling of the electrical circuit equation and mechanical kinetic equation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.465-469
• /
• 2019

In this paper, the design of BLDC (brushless direct current) motors based on torque and back-EMF equations was carried out to assess the application of the motor in concrete vibrators. The air gap flux density of the motor is an important parameter because the length of the motor and the size of the diameter are given. The air gap magnetic flux density was calculated through a simplified magnetic circuit, and basic design of the shape and dimensions of the motor were then determined by carrying out experiments based on torque, back-EMF, and air magnetic flux density equations. After setting the outer and inner diameters, stack lengths, and rated speed of the motor, a detailed design was performed by simulations using the finite element method by designating the diameter and thickness of the motor as the key parameters. The final design to satisfy the target torque and the lowest THD (Total Harmonic Distortion) was carried out along with a simulation.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.857_858
• /
• 2009

On account of small size and light weight, a high-speed machine is regarded as a key technology for many future applications of drive systems. In high-speed applications, permanent magnet (PM) synchronous motors have a number of merits such as high efficiency and high power density. Accordingly, they are suitable for driving the air-blower of a fuel cell electric vehicle (FCEV) where space and energy savings are critical. Particularly, a surface-mounted PM motor of them is mainly used as a high-speed machine. However, the motor has a fatal flaw owing to a retaining can to maintain the mechanical integrity of a rotor assembly. The can results in the increase of magnetic air-gap length in the surface-mounted PM motor. Thus, in this paper, an interior PM motor is designed in order to drive the air-blower of FCEV instead of the surface-mounted PM motor, and the experimental results of two models are compared to verify the capability of the interior PM motor for a high-speed machine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.4
• /
• pp.466-475
• /
• 2010

This study intends to present a direction for the better reforming of fishers'onboard living conditions and proposals for preparing for ratification of the Work in Fishing Convention by means of making a comparison between standards on recent national fishing vessel accommodation facilities and standards on the Work in Fishing Convention and Its Recommendation, 2007, ILO. For the most part of standards on national fishing vessel accommodation facilities are somewhat insufficient to satisfy the provisions in Annex III of the Convention. Considering by items on fishing vessel accommodation facilities, the standards on insect protector, noise and vibration, heating and air conditioning, lighting, persons per sleeping room, recreational facility are not provided in national law. Headroom, separation of accommodation, sleeping room floor area, mattress size, mess room, galley and food storage are partially sufficient for the Convention. In case of sanitary facilities, national standards are not sufficient for the Convention. The other side, facilities related safety of ship and crew such as emergency escape etc., are fully sufficient for the Convention. These insufficiencies caused by different types of fishing vessel depend on originality of fishing method and practices. In the comparison between equivalent tonnage about vessel's length on convention and calculated tonnage of national existing fishing vessel, the difference are 226tons about length 24m and 501tons about length 45m. For that reason, headroom, persons per sleeping room, cabin of sicker and injured, sanitary facilities may decide to use gross tonnage in place of length (L) and the alleviating measure basis of convention. But in case of standards on sanitary facilities which are unsufficient for the Convention, specially in coastal fishing vessel length basis should be adopted with alleviating basis for less than length 24m.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.3
• /
• pp.29-37
• /
• 2000

In this paper, the thrust control of PWM Inverter-fed SLIM(Single-sided Linear Induction Motor) is achieved by vector control and PID control with DSP(TMS320C32). SLIM which used as a conveyor has required the quick response and the constant operating without air gap trembling while it conveys load.Thus, SLIM should have the smallest trembling of air gap length. First, voltage equations for SLIM are calculated from the proposed equivalent circuit in this peper, and not only the exciting current but also the thrust component are obtained from them. The thrust current ripple can be reduced by the vector controller using a slip angle frequency, and the PID controller is also use for the position control.

• The Research Journal of the Costume Culture
• /
• v.26 no.5
• /
• pp.727-743
• /
• 2018

In this study, we used the 3D simulation program to create bodice patterns for adolescents boy students and analyze the fitting and air gap through 3D simulation. The purpose of this study was to select the bodice pattern method that best suited the body shapes of the adolescents male students. The subjects of this study were the French E pattern, Japanese N pattern, and Korean industrial L and J patterns. The applied size was the sixth Korean human body size survey data of 2010 Korea. The age range of the subjects was 13-18 years. DC Suite Program Ver. 5.1 was used, and SPSS 23.0 program was used for data analysis. As a result of comparing the shapes of the bodice patterns in the 3D simulation program, the E pattern had two waist darts on the front and one shoulder dart and one waist dart on the back, and the J and L patterns only had one dart on the back. The N pattern had no darts on either the front or back. As a result of examining the appearance evaluation of the pattern, air gap, color distribution, and clothing cross-section, the E pattern was evaluated as the closest to the body, and the N pattern was evaluated as the pattern with the largest allowance. The J pattern was evaluated as the best fit for body shape of the male adolescents. However, it is necessary to develop a pattern system by adding extra ease in setting the center front length.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.928-934
• /
• 2006

In this paper, the inductive power collector using electromagnetic induction for vehicle such as the electric railway vehicle system is suggested and some ideas for power collector design to improve the power transfer performance are presented. The inductive power of secondary part is related to amount of linked flux to secondary part by the length of air-gap, which is expected by such a system parameter as mutual inductance. This paper will study for the transfer characteristic of power from input to output and equation including mutual inductance.

• Textile Coloration and Finishing
• /
• v.34 no.1
• /
• pp.27-37
• /
• 2022

In this study, a study and interpretation of the spinning process in copolymerized aramid spinning was conducted. In order to proceed with the spinning process modeling and analysis, the spinning process was modeled through the physical property modeling of the spinning solution and the structural modeling of the spinneret, and structural stability and flow of the spinneret for this spinning were analyzed. After modeling the spinning solution and the spinneret in a virtual space, the pack pressure and flow rate when the spinning solution was discharged were simulated. Macroscopically, the structural stability of the spinneret was confirmed at the standard pack pressure (100 kg·f/cm²), and microscopically, the flow rate and pressure drop data of the spinning solution according to the L/D(Length (L)/Diameter (D)) value were analyzed. Based on the research and development of virtual engineering modeling and analysis, we present the possibility of changing the shape and mechanical properties of copolymer aramid fibers according to the spinning process.

• International Journal of Railway
• /
• v.2 no.2
• /
• pp.93-97
• /
• 2009

The experiments for aerodynamic characteristics of railway acoustic screen are performed using 1/61 scaled-down moving model rig facility which employs an axis symmetry and one wire guidance method. The launching mechanism is an air-gun type. The train model for the experiment is the high speed train (Korea Train Express: KTX) and the tested speed is about 300 km/h. The tested train length is 61 em which is corresponding to two units of KTX train. The cross sectional area and weight of train model are 0.00264 $m^2$ and 287 g, respectively. The Reynolds number based on the model train length is $1.2{\times}10^7$. The strength of pressure wave is measured using piezo typed pressure sensor. The measured pick value of pressure was as high as 365 Pa in the shortest gap between the acoustic screen and model train. The measured pressure is well compared with the field test data of mc 779-1 [2] values. However, the experimental data were slightly lower than the mc 779-1 values. The results show the model test can be used as a substitute for the field test.