• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.4
• /
• pp.33-39
• /
• 2014

In this paper, a new on-chip aging sensing circuit based on flip-flops is proposed to detect a circuit failure of MOSFET digital circuits casued by aging phenomenon such as HCI and BTI. The proposed circuit uses timing windows to warn against a guardband violation of sequential circuits, and generates three warning bits right before circuit failures occur. The generated bits can apply to an adaptive self-tuning method for reliable system design as control signals. The aging sensor circuit has been implemented using 0.11um CMOS technology and evaluated by $4{\times}4$ multiplier with power gating structure.

• Journal of Sensor Science and Technology
• /
• v.26 no.4
• /
• pp.292-296
• /
• 2017

It has become ever harder to design reliable circuits with each nanometer technology node under normal operation conditions, a transistor device can be affected by various aging effects resulting in performance degradation and eventually design failure. The reliability (aging) effect has traditionally been the area of process engineers. However, in the future, even the smallest of variations can slow down a transistor's switching speed, and an aging device may not perform adequately at a very low voltage. Because of such dilemmas, the transistor aging is emerging as a circuit designer's problem. Therefore, in this paper, the impact of aging effects on the delay and power dissipation of digital circuits by using nanomneter MOSFET power gating structure has been analyzed.. Based on this analyzed aging models, a reliable digital circuits can be designed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.476-482
• /
• 2009

This paper describes the development of capacitive sensor for the diagnosis of liquid dielectrics, which is widely used as the electrical insulating oil of transformer, circuit breaker, cable and etc. To survey the dielectric properties of the virgin and aged electrical insulating oils, we utilized the highly precise measuring system, using the principle of cross capacitance. The measured properties were used to determine the design factors of the sensor. Then the factors were optimized with the help of computational analysis. To evaluate diagnosis by the sensor, we performed accelerated thermal aging test about electrical insulating oils. The condition of aged specimens were investigated by measurements of relative permittivity i.e. capacitance change by capacitive sensor. And to evaluate the hysteresis characteristics with the change of temperature, we constructed a testing system, which was composed with vacuum drying oven, oil chamber and measuring instruments, such as LCR meter, MUX and so forth. Through the results of this investigation, we confirmed the superior characteristics of the newly developed sensor.

• Journal of Sensor Science and Technology
• /
• v.28 no.1
• /
• pp.17-22
• /
• 2019

As CMOS technology scales down, reliability is becoming an important concern for VLSI designers. This paper analyzes gate-oxide breakdowns (i.e., the time-dependent dielectric-breakdown (TDDB) aging effect) as a reliability issue for combinational circuits with 45-nm technology. This paper shows simulation results for the noise margin, delay, and power using a single inverter-chain circuit, as well as the International Symposium on Circuits and Systems (ISCAS)'85 benchmark circuits. The delay and power variations in the presence of TDDB are also discussed in the paper. Finally, we propose a novel method to compensate for the logic failure due to dielectric breakdowns: We used a higher supply voltage and a negative ground voltage for the circuit. The proposed method was verified using the ISCAS'85 benchmark circuits.

• Journal of Biomedical Engineering Research
• /
• v.32 no.1
• /
• pp.32-36
• /
• 2011

The insufflators in endoscopic surgery supply carbon dioxide to make the air-filled cavity in the abdomen. It contains many kinds of pneumatic and electronic parts and they are connected with the air tubes and electrical wires. The printed circuit boards (PCB) perform wiring, holding and cooling tasks in electronic systems. In this study, the PCB is used as the air channel for insufflators to decrease the cost, volume, and the malfunction according to aging of the device. Three layers of PCB made of FR4 are combined with prepreg as adhesive which has the internal airway channel according to the design. By mounting the pressure sensors and valves, the PCB based fluidic system is implemented. After calibration of flow sensor, the flow rate of the gas also can be measured. The climate test, temperature test, and biocompatibility test showed this idea can be used in insufflators for laparoscopic surgery.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.1
• /
• pp.61-67
• /
• 2014

Conventional synchronous circuits in low power required systems such as sensor systems cannot only satisfy the timing requirement of the low voltage digital systems, but also they may generate wrong outputs under the influence of PVT variations and aging effects. Therefore, in the reliable ultra-low power design, asynchronous circuits have recently been reconsidered as a solution for scaling issues. However, it is not easy to totally replace synchronous circuits with asynchronous circuits in the digital systems, so the interfacing between the synchronous and asynchronous circuits is indispensable for the digital systems. This paper presents a new design for interfacing between asynchronous circuits and synchronous circuits, and the interface circuits are applied to a $4{\times}4$ multiplier logic designed using 0.11um technology.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.2
• /
• pp.223-229
• /
• 2022

During the winter season, when the weather gets colder every year, electricity consumption increases rapidly. The occurrence of fires is increasing due to a short circuit in electrical facilities of buildings such as markets, bathrooms, and apartments with high population density while using a lot of electricity. The cause of these short circuit fires is mostly due to the aging of the wires, the usage increases, and the excessive load cannot be endured, and the wire sheath is melted and caused by nearby ignition materials. In this paper, the load and overheat generated in the electric wire are measured through a complex sensor composed of an overload sensor, a VoC sensor, and an overheat sensor. Based on this, big data analysis is carried out to develop a platform capable of predicting, alerting, and blocking electric fires in real time, and a simulator capable of simulated fire experiments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.3
• /
• pp.485-491
• /
• 2015

This paper shows the design improvement and test model of FAU (Frequency Analysis Unit) in PDD (Partial Discharge Diagnosis system) for 800kV GIS (Gas Insulated Switchgear). We found some problems during operation of previous FAU, such as the aging of fiber-optic converter that can cause communication error, the malfunction of signal analysis circuit etc. And then we solved those problems by design improvement and verified the performance through type test. To monitor partial discharge, the performance of UHF sensor is important but the performance of frequency analysis unit is also very important. So we solved communication error, the malfunction of signal analysis circuit and then increased the operation reliability of FAU by improving fiber-optic converter and signal analysis circuit. Accredited testing laboratory carried out the performance verification test according to performance test criteria and procedure of reliability test standards, IEC-60225, 61000 and 60068 etc. We confirmed the test results which correspond with the performance test criteria.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.115-122
• /
• 1997

In this paper, on-chp atomatic tuning circuit, using proposed integration level approximation technique, is designed to tuning of the variation of RC time-constant due to aging or temperature variation, etc. This circuit reduces the error, the difference between code values and real outputs of integrator, which is drawback of presented dual-slope tuning circuit and eliminates modulations of processing signals in integrated circuit due to fixed tuning codes during ordinary operation. This system is made up of simple integrator, A/D converter and digital control circuit and all capacitors are replaced by programed capacitor arrays in this system. This tuning circuit with 4 bit resolution achieves $-9.74{\sim}+9.68%$ of RC time constant error for 50% resistance variation.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.52-59
• /
• 2022

Currently, Korea is an aging society and is expected to become a super-aged society in about four years. X-ray devices are widely used for early diagnosis in hospitals, and many X-ray technologies are being developed. The development of X-ray device technology is important, but it is also important to increase the reliability of the device through accurate data management. Sensor nodes such as temperature, voltage, and current of the diagnosis device may malfunction or transmit inaccurate data due to various causes such as failure or power outage. Therefore, in this study, the temperature, tube voltage, and tube current data related to each sensor and detection circuit of the diagnostic X-ray imaging device were measured and analyzed. Based on QC data, device failure prediction and diagnosis algorithms were designed and performed. The fault diagnosis algorithm can configure a simulator capable of setting user parameter values, displaying sensor output graphs, and displaying signs of sensor abnormalities, and can check the detection results when each sensor is operating normally and when the sensor is abnormal. It is judged that efficient device management and diagnosis is possible because it monitors abnormal data values (temperature, voltage, current) in real time and automatically diagnoses failures by feeding back the abnormal values detected at each stage. Although this algorithm cannot predict all failures related to temperature, voltage, and current of diagnostic X-ray imaging devices, it can detect temperature rise, bouncing values, device physical limits, input/output values, and radiation-related anomalies. exposure. If a value exceeding the maximum variation value of each data occurs, it is judged that it will be possible to check and respond in preparation for device failure. If a device's sensor fails, unexpected accidents may occur, increasing costs and risks, and regular maintenance cannot cope with all errors or failures. Therefore, since real-time maintenance through continuous data monitoring is possible, reliability improvement, maintenance cost reduction, and efficient management of equipment are expected to be possible.