• Proceedings of the Korea Contents Association Conference
• /
• 2011.05a
• /
• pp.201-202
• /
• 2011

본 연구에는 7.0T 동물용 자기공명영상장치를 이용하여 인간의 췌장암 세포인 CFPAC-1를 이종 이식한 쥐에서 자기공명영상을 획득하여 최적화된 검사 Protocol을 정립하며, 동물 실험에서 밝혀진 종양특성과 확산강조영상과의 비교 분석을 해보고 현성확산계수 영상이 췌장암 이종이식 모형의 종양 세포 내부 구조에 관하여 어떠한 정보를 제공 할 수 있는지 알아보고자 한다. 13마리의 쥐의 26개의 종양을 전형적으로 주입 후에 2~4주 뒤에 직경이 5~10mm가 되었을 때 imaged 하였으며, pathologic specimenm을 위해 sacrificed 하였다. isofluoran gas anesthesia를 이용하여 동물 마취 하였다. 사용된 장비로는 small-animal MR images (7.0-T)를 (Bruker BioSpin GmbH, Rheinstetten, Germany)이용하여 Fast T2-weighted 와 single-shot EPI DW image를 얻었다. 종양은 H&E 염색과 CD31와 VEGF에 대한 면역조직학 염색을 하여 종양의 cellularity와 microvessel density(MVD), 종양 내 괴사 정도를 평가하였다. CFPAC-1의 현성확산계수값은 $0.7327{\pm}0.1075{\pm}10^{-3}mm2/s$이였으며, 현성확산계수는 종양내 괴사 정도와 연관성을 보였다(R = 0.7417, p = 0.0001) 이처럼 현성확산계수는 종양 내 괴사 정도 등의 현미경적구조변화를 반영하는 대리인자로 사용될 수 있음을 확인하였다.

• Korean Journal of Food Science and Technology
• /
• v.22 no.6
• /
• pp.686-689
• /
• 1990

For the monitoring of kimchi fermentation states, pressure detecting sensor and monitoring device were designed and fabricated. The system was consisted of an air tight fermenting tube(31.5 ml), strain gauge type pressure sensor and signal processing device built with operational amplifier and A/D converter, and interfaced to personal computer. Chiness cabbage kimchi was fermented in the plastic container($150{\times}220{\times}160mm$) at $25^{\circ}C\;and\;30^{\circ}C$. The fermentation was monitored with fermenting tubes containing kimchi. The pressure based kimchi fermentation curve was constructed and showed a typical kimchi curing curve having 2 stepwise pressure increasing pattern.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.556-558
• /
• 1996

PLS 2-GeV linac has 11 sets of high power klystron-modulator system as a main RF source for the beam acceleration. The modulators can provide 200-MW peak pulsed power(400-kV, 500-A) with a pulse width of $7.5{\mu}s$(ESW), a maximum pulse repetition rate of 120-Hz at the full power level. The DC power supply provides a 25-kV, 7-Adc and the charging system consists of a charging inductor, charging capacitor, and the diode for reverse current protection. The charged PFN voltage by a LC resonant charging method has two times of the DC high voltage and the pulsed power is delivered to the load by a thyratron switch. To reduced the press of high voltage lit thyratron switch, the command charging is the best method. In this article, the high voltage switch for the command charging method is tested to the start work and the system is presented with the experiment results of the trigger and operational characteristics.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.214-221
• /
• 2010

Radio frequency (RF) subsampling can be used by radio receivers to directly down-convert and digitize RF signals. A goal of a cognitive radio/software defined ratio (CR/SDR) receiver design is to place the analog-to-digital converter (ADC) as near the antenna as possible. Based on this, a band-pass sampling (BPS) frontend for CR/SDR is proposed and verified. We present a receiver architecture based second-order BPS and signal processing techniques for a digital RF frontend. This paper is focused on the benefits of the second-order BPS architecture in spectrum sensing over a wide frequency band range and in multiband receiving without modification of the RF hardware. Methods to manipulate the spectra are described, and reconstruction filter designs are provided. On the basis of this concept, second-order BPS frontends for CR/SDR systems are designed and verified using a hardware platform.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1058-1063
• /
• 2020

This paper proposes a 12-bit SAR A/D(Successive Approximation Register Analog-to-Digital) converter that operates at low power for bio-signal and sensor signal processing. The conventional SAR A/D converter utilized the reduction of the dynamic current, which resulted in reducing total power consumption. In order to solve the limitation of the sampling time due to charging/discharging of the capacitor for reducing dynamic current, the different sampling time on the C-DAC bit switch operation was applied to reduce the dynamic current. In addition, lowering the supply voltage of the digital block to 0.6V led to 70% reduction of the total power consumption of the proposed ADC. The proposed SAR A/D was implemented with CMOS 65nm process 1-poly 6-metal, operates with a supply voltage of 1.2V. The simulation results demonstrate that ENOB, DNL/INL, power consumption and FoM are 10.4 bits, ±0.5LSB./±1.2LSB, 31.2uW and 2.8fJ/step, respectively.

• Journal of Positioning, Navigation, and Timing
• /
• v.4 no.3
• /
• pp.115-122
• /
• 2015

Global Positioning System (GPS) is used in various fields such as communications systems, transportation systems, e-commerce, power plant systems, and up to various military weapons systems recently. However, GPS receiver is vulnerable to jamming signals as the GPS signals come from the satellites located at approximately 20,000 km above the earth. For this reason, various anti-jamming techniques have been developed for military application systems especially and it is also required for commercial application systems nowadays. In this paper, we proposed a dual-channel Global Navigation Satellite System (GNSS) RF ASIC for digital pre-correlation anti-jam technique. It not only covers all GNSS frequency bands, but is integrated low-gain/attenuation mode in low-noise amplifier (LNA) without influencing in/out matching and 14-bit analogdigital converter (ADC) to have a high dynamic range. With the aid of digital processing, jamming to signal ratio is improved to 77 dB from 42 dB with proposed receiver. RF ASIC for anti-jam is fabricated on a 0.18-μm complementary metal-oxide semiconductor (CMOS) technology and consumes 1.16 W with 2.1 V (low-dropout; LDO) power supply. And the performance is evaluated by a kind of test hardware using the designed RF ASIC.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.300-308
• /
• 2010

This paper describes the development of a low-power electrocardiogram (ECG) touch sensor intended for the use with two dry metal electrodes. An equivalent ECG extraction circuit model encountered in a ground-free two-electrode configuration is investigated for an optimal sensor read-out circuit design criteria. From the equivalent circuit model, (1) maximum sensor resolution is derived based on the electrode's background thermal noise, which originates from high electrode-skin contact impedance, together with the input referred noise of instrumentation amplifier (IA), (2) 60 Hz electrostatic coupling from mains and motion artifact are also considered to determine minimum requirement of common mode rejection ratio (CMRR) and input impedance of IA. A dedicated ECG read-out front end incorporating chopping scheme is introduced to provide an input referred circuit noise of 1.3 ${\mu}V_{rms}$ over 0.5 Hz ~ 200 Hz, CMRR of IA > 100 dB, sensor resolution of 7 bits, and dissipating only 36 ${\mu}W$. Together with 8 bits synchronous successive approximation register (SAR) ADC, the sensor IC chip is implemented in 0.18 ${\mu}m$ CMOS technology and integrated on a 5 cm $\times$ 8 cm PCB with two copper patterned electrodes. With the help of proposed touch sensor, ECG signal containing QRS complex and P, T waves are successfully extracted by simply touching the electrodes with two thumbs.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1437-1445
• /
• 2014

In this paper a novel method for angular position determination using sensors with sin/cos output and without an excitation signal, is presented. The linearization of the sensor transfer characteristic and digitalization of the measurement results are performed simultaneously with a goal to increase the measurement resolution. This improvement is particularly important for low angular velocities, and can be used to increase the resolution of incremental Hall, magnetic and optical sensors. This method includes two phases of sin/cos signal linearization. In the first linearization phase the pseudo-linear signal is generated. The second linearization phase, executed by the two-stage piecewise linear ADC, is an additional linearization of the pseudo-linear signal. Based on the LabVIEW software simulations of the proposed method, the contribution of each processing phase to a final measurement error is examined. After the proposed method is applied within $2{\pi}$ [rad] range, the maximal nonlinearity is reduced from 0.3307 [rad] ($18.9447^{\circ}$) to $3{\cdot}10^{-4}$ [rad] ($0.0172^{\circ}$).

• Investigative Magnetic Resonance Imaging
• /
• v.7 no.1
• /
• pp.56-60
• /
• 2003

We present MR diffusion-weighted imaging (DWI) findings of status epilepticus in two patients. DWI showed a focal or diffuse hyperintensity with decreased apparent diffusion coefficient (ADC) value, indicating cytotoxic edema in th e cerebral hemispheric cortices. The hyperintensities were located in the bilateral temporoparietooccipital areas and insular cortex in one patient, and unilaterally in the temporal lobe in the other patient.

• Korean Journal of Food Science and Technology
• /
• v.24 no.6
• /
• pp.524-527
• /
• 1992

To measure of important variables such as temperature, weight, and relative humidity in food processing process, computer-aided data acquisition system was composed of 16 bit microcomputer and PCL-711S interface board. Process variables in dehydration and storage of food were measured through sensors, converters, and computer system which were operated by the PC-LabDAS software for data acquisition, process control, and data analysis. The relationship between measured values of process variables and the output voltages of ADC showed more than 0.99 in $r^2$ value. Response time of sensors was enough fast to measure minute values changed in a moment.