• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.9
• /
• pp.71-80
• /
• 2007

This paper presents a new push-push VCO technique that extracts a second harmonic output signal from a capacitive commonnode in a negativegm oscillator topology. The generation of the $2^{nd}$ harmonics is accounted for by the nonlinear current-voltage characteristic of the emitter-base junction diode causing; 1) significant voltage clipping and 2) different rising and falling time during the switching operation of core transistors. Comparative investigations show the technique is more power efficient in the high-frequency region that a conventional push-push technique using an emitter common node. Prototype 12GHz and 17GHz MMIC VCO were realized in GaInP/GaAs HBT technology. They have shown nominal output power of -4.3dBm and -5dBm, phase noise of -108 dBc/Hz and -110.4 dBc/Hz at 1MHz offset, respectively. The phase noise results are also equivalent to a VCO figure-of-merit of -175.8 dBc/Hz and -184.3 dBc/Hz, while dissipate 25.68mW(10.7mA/2.4V) and 13.14mW(4.38mA/3.0V), respectively.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.545-546
• /
• 2008

This paper presents a low power CMOS low noise amplifier for UWB applications. To reduce the power consumption, two cascode amplifiers was stacked in DC. Designed with $0.18-{\mu}m$ CMOS technology, the proposed LNA achieves 20dB flat gain, below 3dB noise figure, and the power consumption of 5.2mW from a 1.8 V supply voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.139-143
• /
• 2005

In this paper, we propose the design on LNA and Down-mixer for MB-OFDM UWB using $0.18\;{\mu}m$ CMOS. LNA, Down-mixer design result shows that it covers the frequency range ken 3 GHz to 5 GHz. The LNA gain is larger than 12.8 dB, and noise figure about 2.6 dB. Double balanced differential down-mixer is designed less than 2 dB gainflatness, and it has over 30 dB LO leakage, feedthrough characteristics.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.64-72
• /
• 2010

This paper presents a wide range VCO with fine coarse tuning step using a sigma-delta modulation technique for UWB frequency synthesizer. The proposed coarse tuning scheme provides the low effective frequency resolution without any degradation of phase noise performance. With three steps coarse tuning, the VCO has wide tuning range and fine tuning step simultaneously. The frequency synthesizer with VCO was implemented with 0.13 ${\mu}m$ CMOS technology. The tuning range of the VCO is 5.8 GHz~6.8 GHz with the effective frequency resolution of 3.9 kHz. It achieves the measured phase noise of -108 dBc/Hz at 1 MHz offset and a tuning range 16.8 % with 5.9 mW power. The figure-of-merit with the tuning range is -181.5 dBc/Hz.

• Journal of Fashion Business
• /
• v.11 no.3
• /
• pp.35-45
• /
• 2007

This study examined how to create 2D basic pattern of individuals by means of 3-D body figure, which is to develop a flat of individual basic pattern directly from the 3-D body scan data of each subject using that of the upper body of a male adult. In terms of methodology, this study adopted 3D body scan data on system and body to make examinations in the following steps: 1. Standard point and line were set on human body, along with 3-D definition points(feature points). 2. PB was created by modifying horizontal and longitudinal section of scan data. 3. Ways to set reserve were established in the findings of PB planar development. Respective developed flat patterns were compared with pattern findings in previous studies by means of sensory evaluation. As a result, it was found that both system and body model are basic pattern and belong to appropriate pattern as semi-tight-fit basic pattern with overall appropriate tolerances. Thus, this study came to a conclusion that it is feasible and valid to develop theories for flat development as considered herein.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.5
• /
• pp.920-927
• /
• 1994

A development of an efficient 14.0~14.5GHz 3 Watt SSPA is described in this paper, which is applicable to the very small aperture terminal(VSAT) for bidirectional data and voice signal transmission in low cost and with small size. The SSPA consists of two stages of low noise amplifiers using the low noise GaAs FETs. two stages of medium power amplifiers using the medium power GaAs FETs, and three stages of power amplifiers including a balanced amplifier using an internally matched power GaAs FET. The achieved with this seven stage amplifiers are 42dB signal power gain, 7dB noise figure, 35dBm output power at 1dB gain compression point and 2.0 and 1.5 input and output VSWR respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.1
• /
• pp.42-46
• /
• 2003

In this paper, an MMIC broadband amplifier for wireless communication systems has been developed by using an active feedback method. This active feedback operates at much higher frequencies than a method by a spiral inductor feedback and its size is independent of the inductance value. The MMIC broadband amplifier was designed using a $0.5{\;}{\mutextrm{m}}$ MESFET library. The fabricated chip area was $1.4{\;}mm{\;}{\times}{\;}1.4{\;}mm. Measurement showed a gain of 18 dB with a gain flatness of ${\pm}3$ dB in a 1.5 GHz~3.5 GHz band. The maximum output power and the minimum noise figure were 14 dBm and 2.5 dB in the same band, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.11A
• /
• pp.933-940
• /
• 2011

In this paper, Ka-band transceiver for road watch radar system is designed and fabricated. The transceiver for road watch radar system is composed of waveform generator, frequency generator. IF transceiver and RF up/down converter. The transceiver especially has 3 different waveform mode for target detection range. The transceiver had over 150 MHz bandwidth in Ka-band and 22 dBm output power. The receiver gain and noise figure was 30 dB and 4 dB respectively. The receive dynamic range was 65.28dB and amplitude imbalance and phase imbalance of I/Q channel was 0.3 dB and 1.8 degree respectively. The transceiver meets the required electrical performances through the individual tests.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.134-137
• /
• 2008

This paper proposes a novel quadrature VCO(QVCO) based on direct back-gate second harmonic coupling. The QVCO directly couples the current sources of the conventional LC VCOs through the back-gate instead of front-gate to generate quadrature signals. By the second harmonic injection locking, the two LC VCOs can generate quadrature signals without using on-chip transformer, or stability problem that is inherent in the direct front-gate second harmonic coupling. The proposed QVCO is implemented in $0.18{\mu}m$ CMOS technology operating at 2 GHz with 5.0 mA core current consumption from 1.8 V power supply. The measured phase noise of the proposed QVCO is - 63 dBc/Hz at 10 kHz offset, -95 dBc/Hz at 100 kHz offset, and -116 dBc/Hz at 1 MHz offset from the 2 GHz output frequency, respectively. The calculated figure of merit(FOM) is about -174 dBc/Hz at 1 MHz offset. The measured image band rejection is 46 dB which corresponds to the phase error of $0.6^{\circ}$.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.2
• /
• pp.340-347
• /
• 2008

A prototype of 3D clothing design system with a direct pattern development function was suggested, reflecting intuitive design functions and design modifications while considering the fit of clothing patterns with the 3D human body in the virtual 3D space. The research method was as follows. Clothing models were created using a 3D design tool, 3ds max on the surface of 3D human body model made by scanning an actual human body. 3D illustrations were completed by revising the fit and sizing of the human body and clothing models. 2D T-shirt pattern was produced 3D illustrations using from a 3D scanning data modeling solution RapidForm 2004, a 2D conversion program for 3D data called 2C-AN, and Yuka CAD. As a result, the following conclusions were made. The fit of the clothing and human body can be adjusted by reflecting individual body figure characteristics and 3D illustrations over the actual 3D body model. Furthermore, intuitive design support functions were intensified overcoming the weak point of existing 3D clothing design system by developing the direct clothing design in the virtual 3D space. 3D illustration design modifications can be directly reflected on clothing patterns from 3D illustrations by 3D clothing design system developed in this study.