• Journal of Korean Society of Transportation
• /
• v.23 no.5 s.83
• /
• pp.157-167
• /
• 2005

Seoul metropolitan public transport reform results in the introduction of the semi-public operation and distance-based fare policies. With implementation of these policies, public transport revenue allocation has been (will be) evolved very complicated because the existing revenue allocation issues have not only been clearly solved, which is generated by the combined relationship among Korea Railroad Corporation (KRC). Seoul Metropolitan Subway Corporation (SMSC). Seoul Metropolitan Rapid Transit Corporation (SMRTC), and Incheon Rapid Transit Corporation (IRTC), but also the revenue allocation problem between bus and urban railroad-related organizations need to be considered in this combined framework. On top of that. based on the future plans such as the private sector's railroad construction plan(s), the light rail transit construction plans of several local governments and the join of remained bus lines of Seoul metropolitan areas, it is understood that the revenue allocation among public transport operating organization will become one of main issues of operation organization as well as local and central governments. As a basic approach for revenue allocation of public transport operation organizations, the purpose of this paper is to propose an integrated model applicable to estimate degree of service contribution in passenger carriage in the combined public transport network. With a hypothesis that the complete electronic card system is deployed, this paper supposes every passenger's loading and alighting stations is recordable. Thereby, this paper limits research scope as to Seoul metropolitan railroad area since used route(s) between origin and destination stations can not be traceded because transfer stations each passenger path through is not recorded. Each model proposed in the paper is as follows: 1. a generalized cost reflecting passenger's transfer behavior; 2.a K path model for determining similar routes between O-D; 3.an assignment model for loading O-D trips onto the detected similar routes using Logit Model.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.2
• /
• pp.55-68
• /
• 2014

Some infrastructure these days is usually constructed under the ground for it to not interfere the foot-traffic of pedestrians, and thus, it is difficult to visually confirm the accurate location of the site where the establishments must be buried. These technical difficulties increase the magnitude of the problems that could arise from over-reliance on the experience of the worker or a mere blueprint. Such problems include exposure to flood and collapse. This paper proposes a constructor-oriented visualization system via mobile gadgets in general construction sites with occluded structures. This proposal is consisted with three stages. First, "Stage of detecting manhole and extracting features" detects and extracts the basis point of occluded structures which is unoccluded manhole. Next, "Stage of tracking features" tracks down the extracted features in the previous stage. Lastly, "Stage of visualizing occluded constructions" analyzes and synthesizes the GPS data and 3D objects obtained from mobile gadgets in the previous stages. This proposal implemented ideal method through parallel analysis of manhole detection, feature extraction, and tracking techniques in indoor environment, and confirmed the possibility through occluded water-pipe augmentation in real environment. Also, it offers a practical constructor-oriented environment derived from the augmented 3D results of occluded water-pipings.

• Investigative Magnetic Resonance Imaging
• /
• v.18 no.2
• /
• pp.87-106
• /
• 2014

Purpose : To describe how a robust implementation of a radial 3D gradient-echo sequence with stack-of-stars sampling can be achieved, to review the imaging properties of radial acquisitions, and to share the experience from more than 5000 clinical patient scans. Materials and Methods: A radial stack-of-stars sequence was implemented and installed on 9 clinical MR systems operating at 1.5 and 3 Tesla. Protocols were designed for various applications in which motion artifacts frequently pose a problem with conventional Cartesian techniques. Radial scans were added to routine examinations without selection of specific patient cohorts. Results: Radial acquisitions show significantly lower sensitivity to motion and allow examinations during free breathing. Elimination of breath-holding reduces failure rates for non-compliant patients and enables imaging at higher resolution. Residual artifacts appear as streaks, which are easy to identify and rarely obscure diagnostic information. The improved robustness comes at the expense of longer scan durations, the requirement for fat suppression, and the nonexistence of a time-to-center value. Care needs to be taken during the configuration of receive coils. Conclusion: Routine clinical use of radial stack-of-stars sequences is feasible with current MR systems and may serve as substitute for conventional fat-suppressed T1-weighted protocols in applications where motion is likely to degrade the image quality.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.11
• /
• pp.21-30
• /
• 1998

In this paper, a digital current control system using a FPGA(Field Programmable Gate Array) was implemented, and the system was applied to an induction motor widely used as an industrial driving machine. The FPGA designed by VHDL(VHSIC Hardware Description Language) consists of a PWM(Pulse Width Modulation) generation block, a PWM protection block, a speed measuring block, a watch dog timer block, an interrupt control block, a decoder logic block, a wait control block and digital input and output blocks respectively. Dedicated clock inputs on the FPGA were used for high-speed execution, and an up-down counter and a latch block were designed in parallel, in order that the triangle wave could be operated at 40 MHz clock. When triangle wave is compared with many registers respectively, gate delay occurs from excessive fan-outs. To reduce the delay, two triangle wave registers were implemented in parallel. Amplitude and frequency of the triangle wave, and dead time of PWM could be changed by software. This FPGA was synthesized by pASIC 2SpDE and Synplify-Lite synthesis tool of Quick Logic company. The final simulation for worst cases was successfully performed under a Verilog HDL simulation environment. And the FPGA programmed for an 84 pin PLCC package was applied to digital current control system for 3-phase induction motor. The digital current control system of the 3 phase induction motor was configured using the DSP(TMS320C31-40 MHz), FPGA, A/D converter and Hall CT etc., and experimental results showed the effectiveness of the digital current control system.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.2D
• /
• pp.121-127
• /
• 2012

One of the traffic problems has been caused by the illegal parking because of the lack of parking space. Especially, the illegal occupancy of the road near an intersection makes an serious reduction of road capacity. The current illegal parking and stop-prohibited areas have been designated for less than 5 meters from the edge or the corner of the 4-leg intersection. However, in reality, the cars parked at the place over 5 meters have had a significant impact on the intersection traffic. In addition, many variables such as intersection type, size, and service levels should be considered as factors which influence on the traffic condition at the intersection. It was assumed that through and right-turn traffic rate have a significant impact on the 4-leg intersection with the illegal parking or stop near it. This study tried to verify the impact through the simulation implementation with MOE and LOS. It shows a guideline to designate the parking or stop-prohibited area near the 4-leg intersection under various traffic conditions.

• The KIPS Transactions:PartD
• /
• v.8D no.3
• /
• pp.285-294
• /
• 2001

Recently many efforts on the development of automatic processing system for delivery sequency sorting have been performed in ETRI, which requires the use of postal 4-state bar code system to encode delivery points. This paper addresses the issue on the extension of read range and the improvement of image processing method. For the improvement of image processing procedure, applied information acquisition method through basic two thresholds onto the horizontal axial line of gray image based on reference information of 4-state bar code symbology. Symbol values are computed after creating two threshold values based on the obtained information through search of horizontal axial values. The implementation result of 4-state bar code reader are obtained the symbol values within 30~60 msec (58,000~116,000 mail item/hour)without noise removal or image rotation in spite of the incline $\pm 45^{\circ}$.

• Spatial Information Research
• /
• v.23 no.2
• /
• pp.49-57
• /
• 2015

Recently, Through the linkage and opening, the fusion of the spatial information, it is necessary for productive ecosystem to provide a variety of information and to increase the civil use. Depending on the economic growth, demand for quality of life and well-being has been on the increase. Spatial information service contents for the public convenience has emerged to solve the problem such as health, safety, welfare and discomfort of daily life This study aims to implement search services for a tailored residence space through the three-dimensional data modeling on cadastral information. To achieve this goal, we established the requirements for deriving a registered object by investigating recent trend with respect to existing cadastral data model and defined property and relationship. Focusing on Songpa-gu, Jamsil station in Seoul, we implemented search services for a tailored residence space for three-dimensional right analysis in conjunction with residential and commercial complex building. As a result, we derived a way to supply 3D cadastre information through open platforms (VWorld) and to represent efficiently, which is able to improve the quality of spatial information service contents for the public convenience as well as to widen utilization of information.

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.1
• /
• pp.15-22
• /
• 2014

This paper presents the implementation of a control system of pellet boiler using wood pellet as carbon neutral material. The system also has the additional features to provide remote controlling and monitoring based on home networking technology through either public switched telephone networks or mobile communication networks. It consists of three kinds of sub-modules; a main controller provides basic and additional features such as a setting of temperature, a supplying of wood pellet, a controlling of ignition and fire-power, and a removing of soot. The second is temperature controller of individual rooms which is connected to the main controller through RS-485 links. And interface modules with PSTN and mobile networks can support remote controlling and monitoring the functions. The test results under the heating area of $172m^2$ show a thermal efficiency of 93.6%, a heating power of 20,640kcal/hr, and a fuel consumption of 5.54kg/hr. These results are superior to those of the conventional pellet boilers. In order to obtain the such high performance, we newly applied a 3-step ignition flow, a flame detection by $C_dS$ sensor, and a fire-power control by fine controlling of shutter to our pellet boiler.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2D
• /
• pp.153-161
• /
• 2010

The city planning of a local government is a continuous process that does not end with the creation of a plan but proceeds through decision-making, monitoring and evaluation phases. As a new city planning is changed and confirmed, there is a chance to construct a large scale road that is connected with an under constructed road. In this case, the expansion of the width and length of road, the addition of bridges or tunnels, and the change of the size and location of interchanges lead to many changes on road design and construction. In the past, the consignment contracts for a road construction have been made in limited numbers and for limited civil works. Now, it is growing in numbers and is making for large scale multi-works. However, the standard process and guidelines for the consignment contracts have not been suggested yet, so there is difficulty in performing the consigned road construction effectively. In this paper, the important factors for the consignment contracts are determined by construction document reviews and expert interviews. Based on these results, a standard process for the consigned contracts and a guideline for agreeing on construction cost are suggested. The costs that should be paid by a consignor are also defined.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6D
• /
• pp.969-974
• /
• 2006

Labor shortages are a serious problem for Korea's construction industry. The problem is both quantitative and qualitative. There is a shortage in supply as due to a decrease in the influx of new labor, and existing workers are less productive as they age. The problem will only get worse as more and more major public projects are being planned. Options for increasing the labor supply are somewhat limited, and thus efforts need to be made to adopt new technologies that can improve the productivity and efficiency of field work and their processes. This paper introduces seven innovation technologies that have the best potential to increase productivity and thus reduce the burden of labor shortage problems. These include 1) Substitution by use of robotics and automation, 2) development and applications of Innovative materials to reduce on site field work, 3) increase in productivity through the implementation of Information Technology, 4) improved productivity through the application of modules, and prefabrication, 5) prevention of rework and redesign, 6) diversification of labor by integrating labor skills, and 7) improved productivity by standardizing site processes.