• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.239-246
• /
• 2021

Characteristics of hydrodynamics and heat absorption by gas in a directly-irradiated fluidized bed particle receiver (50 mm-ID X 150 mm high) of SiC particles have been determined. Solid holdups of SiC particles show almost constant values with increasing gas velocity. Fine SiC particles (SiC II; dp=52 ㎛, ρs=2992 kg/㎥) showed low values of relative standard deviation of pressure drop across bed but high solids holdups in the freeboard region compared to coarse SiC particles (SiC I; dp=123 ㎛, ρs=3015 kg/㎥). The SiC II exhibited higher values of temperature difference normalized by irradiance due to the effect of additional solar heat absorption and heat transfer to the gas by the particles entrained in the freeboard region in addition to the efficient thermal diffusion of the solar heat received at bed surface. Heat absorption rate and efficiency increased with increasing the gas velocity and fluidization number. The SiC II showed maximum heat absorption rate of 17.8 W and thermal efficiency of 14.8%, which are about 33% higher than those of SiC I within the experimental gas velocity range.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.9
• /
• pp.65-71
• /
• 2004

This paper describes a new adaptive algorithm which can reduce the required computation quantities in the adaptive filter. The proposed S-LMS algorithm uses only the signs of the normalized input signal rather than the input signals when coefficients of the filter are adapted. By doing so, there is no need for the multiplications and divisions which are mostly responsible for the computation quantities. To analyze the convergence characteristics of the proposed algorithm, the condition and speed of the convergence are derived mathematically. Also, we simulate an echo canceller adopting this algorithm and compare the performances of convergence for this algorithm with the ones for the other algorithm. As the results of simulations, it is proved that the echo canceller adopting this algorithm shows almost the same performances of convergence as the echo canceller adopting the SIA algorithm.

• Journal of Korea Multimedia Society
• /
• v.16 no.8
• /
• pp.972-981
• /
• 2013

Non-linear editing is an editing method that, unlike linear editing, enables users to insert a new frame between existing frames. Non-linear editing systems are systems that support such method, and are composed of a computer, a software and a capture board that inputs/outputs video signals. Non-linear editing is used for modern television broadcasts and movie productions. Recorded footage and various graphic sources are combined into one visual content through a non-linear editing system. In this paper, we will look into functions of various non-linear editing softwares (mainly the most common of all; Adobe Premiere) as well as their merits and demerits during the editing process, and will also discuss their future Improvement direction.

• Cartoon and Animation Studies
• /
• s.35
• /
• pp.67-88
• /
• 2014

Internationally, the Korean feature-length animation is not making a successful box office hit. Being a box office hit all around the world is related with entertainment and laughter cannot be excluded as a element that gives such enjoyment. Although the humor would be playing an important role in globalization of Korean animation, studies that analyzed humor in Korean and U.S. animation are still lacking. Recently, there are cases that several Korean animations aim at overseas market entrust pre-production of scenario or storyboard. This paper examines the humor embedded in stories of feature-length animations that had the most differences by analyzing frequency and contents, and through interviews. It also proposes ways to improve the humor embedded in stories of Korean animations.

• Journal of Korea Multimedia Society
• /
• v.13 no.9
• /
• pp.1391-1398
• /
• 2010

Animation is breathing life into drawings through motion. Animation is formed by the afterimage phenomenon, that is, deviation of sequential pictures in every frame makes a person possibly perceive it as a live video. Consequently, animation is mostly produced using traditional frame-by-frame methods. The study of relations on timing has been a major concern of animation theory. Nevertheless, issues of timing on production outcomes and effectiveness are mostly ignored. Special focus, analysis and leadership studies on timing are addressed on animatics. Creating better timing through animatics, that is writing movies, directing, scheduling and amending storyboard in pre-production stage, eventually shorten time to animation production. This research is centered on animatics as a cutting edge educational courses. This course will introduce students to the animation production skill and instructors to in-depth teaching points. One of the concepts that we want to go for is keeping animatics apart from mere storyboard. In conjunction with the animation theory, this research conducted under the focus of production of animatics will lead to more efficient way of education on animatics.

• Resources Recycling
• /
• v.15 no.1 s.69
• /
• pp.3-11
• /
• 2006

Fast pyrolysis of Quercus acutissima was carried out in a fluidized bed pyrolyser and then the physicochemical properities of obtained bio-oil were analyzed using GC/MS. The yields of bio-oil of Quercus acutissima and Larix leptolepis from a fluidized bed pyrolyzer were maximized at $350^{\circ}C\;and\;400^{\circ}C$, respectively. This is due to the difference or cellulose content between the two tree species. Above the optimum temperature, the yields of char and oil decreased as the reaction temperature increased, but the yield of gas-phase and water fraction increased. It is concluded that this phenomenon is occured by secondary pyrolysis in the free board. The feeding rate of the sample in a fluidized bed pyrolyser did not affect the yields and composition of products, because of a sufficient mixing between bed materials and sand.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.525-530
• /
• 2005

The erosion rate of water wall tube has been measured and discussed in a commercial circulating fluidized bed combustor (200 ton steam/hr, $4.97{\times}9.90{\times}28.98m\;height$). Tube thickness was measured with ultrasonic method. Severe tube erosion rate was observed in the splash region on all waterwalls including wingwalls. The tube erosion rate increased after an initial decrease as height from the distributor increased. The difference of erosion rate among wing walls was found due to unbalanced distribution of gas and solid flow rates. The erosion rate of the wing wall increased as location of the wing wall became closer to the center of combustor crosssection.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.1
• /
• pp.113-121
• /
• 1989

A software interface called CGI-K including device driver routines and graphics primitives for the grphic board "K" was designed, implemented in the Design Automation Laboratory of KAIST and installed on IBM PC/AT, using assembly and C language supported by TMS 34010 grphics processor. Several algorithms generating the graphics primitives such as box, circle, pie chord are proposed. The drawing speed of CGI-K on the graphic board K was found out to be three to ten times faster than that of the EGA for several examples. A 2-D graphics editor called GRIM (graphics input and modification) and a 3-dimensional graphics renderer called IPCHE which can draw 3-D objects were developed as two major application programs running on CGI-K. The graphics primitives supported in GRIM include polygon, box, circle, and ace. The IPCHE receives a 3-D objects data file and displays the 3-D object on the screen with hidden surface removal, shading, and perspective scaling.

• Proceedings of the Korean Information Science Society Conference
• /
• 1998.10c
• /
• pp.279-281
• /
• 1998

CSCW는 지리적으로 분산된 작업자 간의 효율적인 의사소통을 위해 화상회의, 채팅(chatting), 화이트 보드(white board), 그리고 텔리포인팅(telepointing)과 같은 기능들을 제공한다. 이 중 텔리포인팅은 지역 시스템(local system)의 공유 윈도우(shard window)에서 텔리포인터(telepointer)를 통해 발생한 이벤트를 원격지 시스템(remote System)의 공유 윈도우에서 나타낼 수 있도록 하는 기능을 제공함으로써 작업자 간의 보다 효율적인 의사소통을 가능하게 한다. 이러한 의사소통 기능으로써의 텔리포인팅은 원격진료, 공동작업 플랫폼에 관한 연구에서 응용된 바 있으나 공동저작을 위한 텔리포인팅 기능에 관한 연구 및 이를 공동저작 관리 시스템 구조에 관한 연구가 미흡하다. 공동제작에서의 텔리포인팅은 저작자 간의 의사소통을 위한 기능 뿐만 아니라 동기적 공동저작과 동기적 프리젠테이션을 위한 기능으로써 응용될 수 있어야 한다. 이를 위해 공동저작 관리 시스템은 저작자 그룹인 세션(session) 단위로 텔리포인터에 대한 권한 관리와 텔리포인팅을 통한 공유객체 엑세스(access) 기능을 제공해야 한다. 또한 텔리포인팅 구조(telepointing architecture)는 텔리포인팅 이벤트의 멀티캐스팅(multicasting) 및 동기화(synchronization)를 위해 중앙에서 이벤트를 조정하는 텔리포인팅 조정 에이전트 (telepointing coordination agent)와 각 저작자의 지역 시스템에 존재하며 공유 윈도우로부터 지역 이벤트(local event)를 인식하고 텔리포인팅 이벤트를 공유 윈도우에 알리는 텔리포인팅 지역 에이전트(telepointing local agent)로 구성되어야 한다. 본 논문은 공동저작을 위한 텔리포인팅의 기능들과 이를 위한 공동저작 관리 시스템 구조를 설명하고 텔리포인팅 구조를 제시한다.cid 함량이 가장 많이 용출된 분획은 sodium hydroxide 부분으로서 hemicellulose구조가 polyuronic acid의 형태인 것으로 사료된다. 추출획분의 구성단당은 여러 곡물연구의 보고와 유사하게 glucose, arabinose, xylose 함량이 대체로 높게 나타났다. 점미가 수가용성분에서 goucose대비 용출함량이 고르게 나타나는 경향을 보였고 흑미는 알칼리가용분에서 glucose가 상당량(0.68%) 포함되고 있음을 보여주었고 arabinose(0.68%), xylose(0.05%)도 다른 종류에 비해서 다량 함유한 것으로 나타났다. 흑미는 총식이섬유 함량이 높고 pectic substances, hemicellulose, uronic acid 함량이 높아서 콜레스테롤 저하 등의 효과가 기대되며 고섬유식품으로서 조리 특성 연구가 필요한 것으로 사료된다.리하였다. 얻어진 소견(所見)은 다음과 같았다. 1. 모년령(母年齡), 임신회수(姙娠回數), 임신기간(姙娠其間), 출산시체중등(出産時體重等)의 제요인(諸要因)은 주산기사망(周産基死亡)에 대(對)하여 통계적(統計的)으로 유의(有意)한 영향을 미치고 있어 $25{\sim}29$세(歲)의 연령군에서, 2번째 임신과 2번째의 출산에서 그리고 만삭의 임신 기간에, 출산시체중(出産時體重) $3.50{\sim}3.99kg$사이의 아이에서 그 주산기사망률(周産基死亡率)이 각각 가장 낮았다. 2. 사산(死産)과 초생아사망(初生兒死亡)을 구분(區分)하여 고려해 볼때 사산(死産)은 모성(母性)의 임신력(姙娠歷)과 매우 밀접한 관련이 있는 것으로 사료(思料)되었고 초생아사망(初生兒死亡)은 미숙아(未熟兒)와 이에 관련된 병발이 거의 결정적(決定的) 원인(原因)이 된다고 사료(思料)되었다. 3. 주산기사망률(周産基死亡率)을 감소시키는 관점(觀點)에서의 모자보건사업(母子保健事業)은 미숙아방지책(未熟兒防止策

• Journal of Advanced Navigation Technology
• /
• v.18 no.6
• /
• pp.541-545
• /
• 2014

Rec. ITU-R M.1842-1 is international recommendation for VHF band communication guideline in maritime mobile service RR Appendix 18 channels. In this paper, we simulate 28.8 kbps VHF ${\pi}$/4-DQPSK digital baseband modem compatible with the recommendation, then it is designed and implemented with FPGA. Cazac sequence is used as a preamble since packet format is not defined untill now in the recommendation. Baseband modem is designed by VHDL language and implemented on NEXYS4 development platform having Atrix7 FPGA chip from Xilinx. For wireless communication test of total prototype system, ADC/DAC board is implemented and EV9730 RF module is utilized. From the experimental results, implemented FPGA modem shows spectral bandwidth of 25 kHz and successful data exchanges between tx and rx communication platform.