• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.405-409
• /
• 2010

New sol-gel precursors having the ability to protect iron against corrosion were synthesized and used to prepare organic-inorganic hybrid coatings based on epoxy. Bisphenol A epoxy was modified with 3-isocyanatopropyltriethoxysilane to improve the compatibility, and water and HCl were used as catalysts for sol-gel process. Various coating formulations were prepared depending on the type of sol-gel precursors and the amount of each ingredient, and cast on iron substrates by dip-coating and thermally cured. Corrosion protection properties of coated iron were studied by a salt spray test and electrochemical impedance spectroscopy under 0.1 M NaCl electrolyte. Hybrid coatings containing anticorrosive functional group exhibited excellent corrosion protection on iron, compared to that of typical hybrid coatings. From electrochemical impedance spectroscopy, the hybrid coatings containing anticorrosive functional group could maintaine the initial impedance after 500 h, while the impedance of hybrid coatings without them started to decrease after 24 h.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.3 s.40
• /
• pp.39-45
• /
• 2006

This study was investigated the thermal properties of underfill with various epoxy resins using thermal analysis methods such as differential scanning calorimetry (DSC), thermo gravimetry analysis (TGA), dynamic mechanical analysis (DMA) and thermo-mechanical analysis (TMA). And, the adhesion strength of the underfills/FR-4 substrate was evaluated. The glass transition temperature (Tg) of underfill which was composed the cycolaliphatic epoxy resin was lower than that of underfill which was not composed the cycolaliphatic epoxy resin. The thermal degradation of underfill was composed of two processes, which involved chemical reactions between the degrading polymer and oxygen from the air atmosphere. The coefficient of thermal expansion (CTE) of underfill which was composed the cycolaliphatic epoxy resin was higher than that of underfill which was not composed the cycolaliphatic epoxy resin. The excessive curing temperatures caused a weak boundary layer of epoxy resin, which resulted in a deterioration of mechanical properties in the epoxy resin and thus led to poor adhesion property between the underfill/FR-4 substrate.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.331-337
• /
• 2005

In general, alkanethiolates having carboxylic acid in the tail group have been used as biorecepton. In this study, we have immobilized a cytochrome c protein using conjugated aromaticthiolates in order to improve the electrical property and physical stability of alkanethilolates. The pattern formation of self-assembled aromaticthiolate monolayers was as follow. Aromatic thiolates bound on the gold surface by the adsorption of 4'-mercapto-biphenyl-4-carboxylic acid and 4-mercapto-[1,1';4',1']terphenyl-4'-carboxylic acid were oxidized by the irradiation of deep UV light through a negative mask. The negative type pattern of the self-assembled monolayer (SAM) was obtained by developing with a deionized water. The pattern formation and electrical conductivity of aromaticthiolate SAMs was investigated by the measurements of STM and AFM. In addition, cytochrome c or ferrocene amide was immobilized onto the patterned substrate. We also studied on the effect of conjugated aromatic thiolates on the electrical activity of cytochrome c or ferrocene amide by cyclic voltammetry.

• Polymer(Korea)
• /
• v.30 no.5
• /
• pp.407-411
• /
• 2006

The SiC-based ceramic nanopatterns were prepared by placing polydimethylsiloxane (PDMS) mold from DVD master on the spincoated polyvinylsilaeane (PVS) or allylhydridopolycaybosilane (AHPCS) as ceramic precursors to fabricate line pattern via UV-nanoimprint lithography (UV-NIL), and subsequent pyrolysis at $800^{\circ}C$ in nitrogen atmosphere. As the dimensional change of polymeric and ceramic patterns was comparatively investigated by AFM and SEM, the shrinkage in height was 38.5% for PVS derived pattern and 24.1% for AHPCS derived pattern while the shrinkage in width was 18.8% for PVS and 16.7% for AHPCS. It indicates that higher ceramic yield of the ceramic precursor resulted in less shrinkage, and the strong adhesion between the substrate and the pattern caused anisotropic shrinkage. This preliminary work suggests that NIL is a promissing route for fabricating ceramic MEMS devices, with the development on the shrinkage control.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.350-357
• /
• 2000

Curing behaviors of glass/epoxy prepreg for printed circuit boards (PCB) were studied by using dielectrometer and differential scanning calorimeter. This prepreg was showed the lowest ionic viscosity at about 115$^{\circ}C$, and then the ionic viscosity was gradully increased up to 15$0^{\circ}C$. This indicated that the curing reaction of this prepreg started at 115$^{\circ}C$ and the molecular weight was increased by the accelerated thermal cross-linking reaction. The loss factor and tan $\delta$ values were also measured and discussed. The dielectric behaviors of this prepreg system were also measured according to the cure cycle for PCB. This material was found to be thermally stable up to about 30$0^{\circ}C$ and then was showed an abrupt decomposition beyond this temperature.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.298-304
• /
• 2004

We fabricated a polymer dispersed liquid crystal (PDLC) cell using LC with negative dielectric anisotropy and UV curable monomer exhibiting transparent state initially (called normally transparent (NT)) and studied the electro-optic characteristics. The NT PDLC cell made with the ratio of LC : monomer = 70/30 wt%, curing temperature of 20 $^{\circ}C$ and strong UV intensity of 198 ㎽/$\textrm{cm}^2$ had high contrast ratio and showed good electro-optic characteristics. In this condition, LC is aligned vertically on the substrate due to the vertical alignment layer and the polymer made with the UV exposure does not influence the alignment of the LC much. Therefore, the transmittance at the zero voltage is very high and the scattering state of the cell is good after applying the voltage because LC with negative dielectric anisotropy tries to align perpendicular to the field. And also, the NT PDLC cell showed better viewing angle characteristics than that in the normally scattering (NS) PDLC.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.155-161
• /
• 2018

A Si chip with the Cu/Au bumps of $100-{\mu}m$ diameter was flip-chip bonded using different anisotropic conductive adhesives (ACAs) onto the local stiffness-variant stretchable substrate consisting of polydimethylsiloxane (PDMS) and flexible printed circuit board (FPCB). The average contact resistances of the flip-chip joints processed with ACAs containing different conductive particles were evaluated and compared. The specimen, which was flip-chip bonded using the ACA with Au-coated polymer balls as conductive particles, exhibited a contact resistance of $43.2m{\Omega}$. The contact resistance of the Si chip, which was flip-chip processed with the ACA containing SnBi solder particles, was measured as $36.2m{\Omega}$, On the contrary, an electric open occurred for the sample bonded using the ACA with Ni particles, which was attributed to the formation of flip-chip joints without any entrapped Ni particles because of the least amount of Ni particles in the ACA.

• Polymer(Korea)
• /
• v.28 no.1
• /
• pp.3-9
• /
• 2004

Silane modified perfluoropolyethers (SPFPE) was synthesized as a self-assembled mono-layers (SAMs) thin film for micro-electro mechanical system (MEMS). SPFPE was compared to the Perfluoropolyethers (PFPE) as well as octadecyltrichlorosilane (OTS) and perfluorooctyltrichlorosilane (FOTS) with respect to the development of hydrophobicity in the SAMs surface. SPFPE shows less hydrophobicity than those of OTS and FOTS. Thermal annealing of SPFPE SAMs resulted in the enhancement of hydrophobicity as much as those of OTS and FOTS. The SAMs formed from SPFPE were found to be similar as OTS and FOTS SAMs with smooth R$\sub$a/ values of 0.3 nm. However, the flexible chain mobility of SPFPE resulted in 50% reduction as much as the fiction force in OTS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.181.1-181.1
• /
• 2016

플렉서블 디스플레이 및 태양전지가 지향하고 있는 저가, 고속의 대량 생산을 위해서는 필름을 기반으로 하는 연속 공정에 의한 대량의 ITO 박막의 증착이 필수적이다. 이로 인해 롤투롤(roll-to-roll) 스퍼터링법을 이용한 ITO 박막의 연속 증착 공정이 차세대 플렉서블 디스플레이 및 태양전지의 대량 생산을 위한 해결책으로 각광받고 있다. 그러나 대부분의 폴리머 필름의 경우 증착 시 발생되는 열 또는 플라즈마에 의해 방출되는 수분과 유기 솔벤트 같은 오염 물질들에 의한 ITO 박막의 특성 저하와, 낮은 열적 안정성을 가지는 기판 특성상 고온(>$200^{\circ}C$)에서 증착이나 후 열처리를 할 수가 없기 때문에, 낮은 저항과 높은 광투과도 특성을 가지는 ITO 필름을 제작하기 위한 공정 최적화가 필요하다. 따라서, 본 연구에서는 롤투롤 스터링법으로 PET 필름 위에 Sn함량이 각각 3, 5, 7.5 10% 도핑된 ITO 타겟을 사용하여 ITO 박막을 증착 하였고, 전기적 광학적 특성을 조사하여 롤투롤 스퍼터링법으로 우수한 전기 전도도와 광투과도 특성을 가지는 ITO/PET 필름의 증착 조건을 최적화 하였다. 또한, ITO 증착 시 필름에서 발생하는 수분에 의한 ITO 박막의 특성 저하 현상에 대하여 조사하였다.

• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.469-473
• /
• 2007

In this study, oligo(3-methylthiothiophene) was synthesized from thiophene derivative according to the method of reductive coupling using palladium catalyst. For the preparation of monomer, 3-methylthiothiophene was first synthesized through the metal-halogen exchange reaction of 3-bromothiophene with n-butyllithiuim, and the corresponding 2,5-dibromo-3-methylthiothiophene was formed by bromination. Their synthesis and characterization were determined by $^1H-NMR$ and ATR analyses. Thermal stability of the oligothiophene was monitored by thermogravimetric analysis (TGA). Thermal evaporation of the oligo(3-methylthiothiophene) on the substrate was attempted for OTFT applications.