• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.878-886
• /
• 2009

This paper proposes an optimal algorithm for generating a train speed profile giving optimal energy efficiency based on GA (Genetic Algorithm) and shows its effectiveness with simulations. After simplifying the train operation mode to a maximum traction, a coasting and a maximum breaking, adjusting the coasting point to minimize the train consuming energy is the basic scheme. Satisfying the two constraints, running distance and running time between two stations, a coasting point is determined by GA with a fitness function consisting of a target running time. Simulation results have shown that multiple coasting points could exist satisfying both of the two constraints. After figuring out consumed energies according to the multiple coasting points, an optimal train speed profile with a coasting point giving the smallest consumed energy has been selected. Simulation blocks for the train performance simulation and GA have been designed with the Simulink.

• Journal of the Korean Society for Railway
• /
• v.17 no.3
• /
• pp.165-170
• /
• 2014

The resistance to motion of the Korean next-generation high-speed train (HEUM-430X) was assessed on the basis of 12 coasting test runs at coasting speeds up to approximately 380km/h. Two different methods, a linear regression method and a time-integral method, were employed to calculate decelerations from the time-velocity data and the time-distance data, respectively, and an equation of resistance to motion was devised from the deceleration data calculated at each time section. The effect of an improvement of the aerodynamic shape on the resistance to motion was investigated, with the results showing that the running resistance was reduced by about 15% due to these improvements. An increase of approximately 28% of the running resistance was also noted when running in a tunnel relative to running through an open field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.1-8
• /
• 1995

In the companion paper of the present paper, a coast down test method to determine the resistance forces on running vehicle based on the distance-time measurement was explained along with the suggestions to improve its accuracy and testing methodology. In the present paper some of the suggestions discussed previously are implemented and actually road tested to see the applicability of the improved method(short distance method) in the field. From the results. it is shown that the short distance method which requires only 600m long proving ground road gives at least comparable results on the accuracy compared to the original S-t method which requires 2000m. It is hoped that the present method be further refiend to give more accurate results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.51-61
• /
• 1995

A coast down test mothod has been used to determine the resistance forces on running vehicle due to the aerodynamic drag, rolling resistance and driveline resistance. Most of the tests, however, are based on the Velocity-Time measurements, which require a sophisticated velocity measuring device and contain much error by nature. In the present study a coast down test method based on Distance-Time measurements is introduced, which contains the original idea of Russian scientist Prof. Petrushov along with the suggestions for improvement of the accuracy.

• Journal of the Korean Society for Railway
• /
• v.18 no.4
• /
• pp.309-316
• /
• 2015

The contribution of exterior devices such as bogie fairings and pantographs to running resistance was estimated on the basis of coasting tests at up to 350 km/h with the help of the Korean Next Generation High speed train (HEMU-430X). In order to assess the reduction of air resistance by nose car's bogie fairing, coasting tests were conducted with a removable bogie fairing at various speed ranges. And, the contribution of the pantograph to air resistance was also estimated with coasting tests that include the pantograph's rising and descent modes. The linear regression method was used to examine decelerations from time-velocity data and the equation of resistance to motion is proposed from the deceleration data. From the aerodynamic term of the equation of resistance to motion, the contribution to air resistance by nose car's bogie fairing and pantograph was estimated. The results show that the air resistance was reduced by about 3.8% by the nose car's bogie fairing. And, the 3.9% increase of air resistance by the pantograph (open knee mode) has been found.

• Journal of the Korean Society for Railway
• /
• v.10 no.2 s.39
• /
• pp.153-160
• /
• 2007

To start or stop the train safely within the limited traveling distance, it is necessary to guarantee the proper traction or braking force. Presently, most trains are run by the electrical power and have adopted a combined electrical and mechanical(friction) braking system. In order to design a good traction or a brake system, it is essential for designers to predict the traction or brake performance. In this paper, the traction/coasting/braking performances analysis program has been developed and verified by comparing the simulation results with on-line test results of the Korean high speed train(HSR-350); Both results match very well. Consequently, the designers can predict the traction/coasting/braking performances of trains by using the proposed program under various operating conditions.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.371-376
• /
• 2003

The objective of this paper is to compare the site-to-site variability of ISO 10844 pass-by-noise test sites. In order to investigate the site-to-site variance of test surfaces, European commercial tires are tested at seven different test sites. Three Korea test sites and four Europe test sites are selected.. The pass by noise test is executed according to a 2001/43/EC regulation. A]though the ISO surface has a very specific track composition, it does not reduce the variation of pass-by-noise measurements over the surface of test sites. This paper shows that the test results of pass-by-noise level are different depending on the test sites. The correlation obtained in this work is able to predict the pass by noise level for certain test site using the data measured from another test site. 17he prediction value is range with an error within 1dB(A).

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.242-244
• /
• 2020

본 논문은 PMSM 센서리스 운전 중에 적은 속도 오차로 플라잉스타트하는 방법을 제안한다. 철도 차량 운전시 손실을 줄이기 위해 인버터의 스위치를 모두 off하고 관성으로만 운전하는 타행운전을 자주 하게 되는데 센서리스 운전시 타행운전 상태에서 회전자의 속도와 위치를 알 수 없어 문제가 된다. 따라서 플라잉스타트에서 회전자의 속도와 위치를 빠르게 추정할 수 있는 방법이 필요하다. 기존의 방법은 플라잉스타트에서 3번의 영전압 합성을 통해 회전자의 속도와 위치를 추정해 내는 방법인데, 이 때 전류 정보에 오차가 존재할 경우 속도와 위치 오차가 발생하게 된다. 따라서 본 논문에서 4번의 영전압 합성을 통해 전류 정보에 오차로 인한 속도와 위치 오차를 저감시킬 수 있는 방법을 제안한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.61-66
• /
• 2012

Conventional method to transform vehicle driving condition to engine operation mode is to use vehicle road load under neutral gear and mechanical efficiency of drivetrain. But this method requires additional measurement of efficiency of drivetrain on a test rig. And this measurement is normally done at fixed speed and thus estimated accuracy of engine operation mode is not considered to be high enough. This study suggests new method to calculate engine operation mode for prescribed driving mode such as NEDC using vehicle coastdown test under gear engaged condition without measurement of mechanical efficiency of drivetrain. Coastdown test was done under neutral and gear engaged condition for comparison and also trial to extract mechanical loss of drivetrain was carried out. Calculated engine torque by conventional and newly suggested method was compared with actually measured torque of a vehicle on a chassis dynamometer during NEDC. Newly suggested method showed slightly higher accuracy of accumulated brake work during NEDC.

• Journal of the Korean Society for Railway
• /
• v.14 no.2
• /
• pp.167-173
• /
• 2011

This paper considers the problem of revising train departure time to reduce electric power consumption of mass rapid transit (MRT) railways. The motion of a train running between stations is divided into three phases: traction, coasting, and deceleration phases. The traction phase requires high electric power to operate MRT railways. In the coasting phase, the train moves stably by consuming little or no power. The deceleration phase is a braking mode and produces some electric power called regenerated brake power owing to inertia force for the train generated In the traction and coasting phases. The regenerative energy can be used by other accelerating trains within a specific range from the train and thereby the power consumptions of train can be reduced. We developed a mixed integer programming model to solve the problem. To validate the suggested model, a computational experiment was conducted using real data from Korea Metropolitan Subway.