• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.29-36
• /
• 2004

A flexible packaging scheme, which includes chip packaging, has been developed using a thinned silicon chip. Mechanical characteristics of thinned silicon chips are examined by bending tests and finite element analysis. Thinned silicon chips (t<30 $\mu\textrm{m}$) are fabricated by chemical etching process to avoid possible surface damages on them. And the chips are stacked directly on $Kapton^{Kapton}$film by thermal compressive bonding. The low height difference between the thinned silicon chip and $Kapton^{Kapton}$film allows electroplating for electrical interconnection method. Because the 'Chip' is embedded in the flexible substrate, higher packaging density and wearability can be achieved by maximized usable packaging area.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.1-10
• /
• 2009

As a demand for the portable device requiring smaller size and better performance is in hike, reducing the size of conventionally used planar 2 dimensional chip cannot be a solution for the enhancement of the semiconductor chip technology due to an increase in RC delay among interconnects. To address this problem, a new technology - "3 dimensional (3D) IC chip stack" - has been emerging. For the integration of the technology, several new key unit processes (e.g., silicon through via, wafer thinning and wafer alignment and bonding) should be developed and much effort is being made to achieve the goal. As a result of such efforts, 4 and 8 chip-stacked DRAM and NAND structures and a system stacking CPU and memory chips vertically were successfully developed. In this article, basic theory, configurations and key unit processes for the 3D IC chip integration, and a current tendency of the technology are explained. Future opportunities and directions are also discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.28-35
• /
• 2010

In the display industry, COG bonding method is being applied to production of LCD panels that are used for mobile phones and monitors, and is one of the mounting methods optimized to compete with the trend of ultra small, ultra thin and low cost of display. In COG bonding process, electrical characteristics such as contact resistance, insulation property, etc and mechanical characteristics such as bonding strength, etc depend on properties of conductive particles and epoxy resin along with ACF materials used for COG by manufacturers. As the properties of such materials have close relation to optimization of bonding conditions such as temperature, pressure, time, etc in COG bonding process, it is requested to carry out an in-depth study on characteristics of COG bonding, based on which development of bonding process equipment shall be processed. In this study were analyzed the characteristics of COG bonding process, performed the analysis and reliability evaluation on electrical and mechanical characteristics of COG bonding using ACF to find optimum bonding conditions for ACF, and performed the experiment on bonding characteristics regarding fine pitch to understand the affection on finer pitch in COG bonding. It was found that it is difficult to find optimum conditions because it is more difficult to perform alignment as the pitch becomes finer, but only if alignment has been made, it becomes similar to optimum conditions in general COG bonding regardless of pitch intervals.

• Journal of Welding and Joining
• /
• v.25 no.2
• /
• pp.6-15
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.647-648
• /
• 2006

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.1
• /
• pp.72-80
• /
• 1997

A 750 MHz CATV amplifier module has been designed and fabricated using PHEMT chips on alumina board. Developed 2-stage push-pull amplifier using wire bounded PHEMT chips shows 19dB gain, 15dB return loss and 4. 2dB noise figure over 50-750MHz frequency range. These results are superior to the characteristics of the commer-cially abailable 750MHz amplifier module. In this paper, brief background of the amplifier design, the circuit diagram and the test result have been presented.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.981-984
• /
• 2010

생산성 증가 및 비용 절감을 위해 반도체 공정 기술을 단순화 시키는 것이 필요하다. WBL(Wafer Backside Lamination) 기술을 이용해 필름(film) 형태로 얇은 다이접착제를 웨이퍼(wafer)에 접착하여 반도체 칩과 PCB를 붙이는 방법과 직접 PCB에 다이접착제를 붙이는 방법을 사용하면 획기적으로 공정을 단순화 시킬 수 있다. 하지만 Lamination 기법은 고온을 이용하여 모듈화된 PCB에 접착하므로 전도와 복사에 의해 주변 접착제 필름이 녹아 버리는 문제점이 발생한다. 본 연구에서는 고온으로 인한 필름 융해 현상을 방지하기 위하여 배크라이트를 설치하였으며 CFD 해석을 통해 PCB와 반도체 칩을 접착시킬 때 열이 PCB에 미치는 영향을 살펴보았다.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.55-61
• /
• 2010

The device with tantalum silicide heater were bonded by Ag paste and Au SBB(Stud Bump Bonding) onto the Au coated substrate. The shear test after Au ABB and the thermal performance under current stressing were measured. The optimum condition of Au SBB was determined by fractured surface after die shear test and $350^{\circ}C$ for substrate, $250^{\circ}C$ for die during flip chip bonding with bonding load of about 300 g/bump. With applying 5W through heater on the device, the maximum temperature with Ag paste bonding was about $50^{\circ}C$. That with Au SBB on Au coated Si substrate showed $64^{\circ}C$. The difference of maximum temperatures is only $14^{\circ}C$, even though the difference of contact area between Ag paste bonding and Au SBB is by about 300 times and the simulation showed that the contact resistance might be one of the reasons.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.74-74
• /
• 2010

모바일 정보통신기기를 중심으로 전자패키지의 초소형화, 고집적화를 위해 플립칩 공법의 적용이 증가되고 있는 추세이다. 플립칩 패키징 접합소재로는 솔더, ICA(Isotropic Conductive Adhesive), ACA(Anisotropic Conductive Adhesive), NCA(Non Conductive Adhesive) 등과 같은 다양한 접합소재가 사용되고 있다. 최근에는 언더필을 사용하는 플립칩 공법보다 미세피치 대응성을 위해 NCP를 이용한 플립칩 공법에 대한 요구가 증가되고 있는데, NCP의 상용화를 위해서는 공정성과 함께 신뢰성 확보가 필요하다. 본 연구에서는 LDI(LCD drive IC) 모듈을 위한 COF(Chip-on-Film) 플립칩 패키징용 NCP 포뮬레이션을 개발하고 이를 적용한 COF 패키지의 신뢰성을 조사하였다. 테스트베드는 면적 $1.2{\times}0.9mm$, 두께 $470{\mu}m$, 접속피치 $25{\mu}m$의 Au범프가 형성된 플리칩 실리콘다이와 접속패드가 Sn으로 finish된 폴리이미드 재질의 flexible 기판을 사용하였다. NCP는 에폭시 레진과 산무수물계 경화제, 이미다졸계 촉매제를 사용하여 다양하게 포뮬레이션을 하였다. DSC(Differential Scanning Calorimeter), TGA(Thermogravimetric Analysis), DEA(Dielectric Analysis) 등의 열분석장비를 이용하여 NCP의 물성과 경화거동을 확인하였으며, 본딩 후에는 보이드를 평가하고 Peel 강도를 측정하였다. 최적의 공정으로 제작된 COF 패키지에 대한 HTS (High Temperature Stress), TC (Thermal Cycling), PCT (Pressure Cooker Test)등의 신뢰성 시험을 수행한 결과 양산 적용 가능 수준의 신뢰성을 갖는 것을 확인할 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.3
• /
• pp.9-17
• /
• 2008

Cu mushroom bumps were formed by electrodeposition and flip-chip bonded to Sn substrate pads. Contact resistances of the Cu-mushroom-bump joints were measured and compared with those of the Sn-planar-bump joints. The Cu-mushroom-bump joints, processed at bonding stresses ranging from 19.1 to 95.2 MPa, exhibited contact resistances near $15m\Omega$/bump. Superior contact-resistance characteristics to those of the Sn-planar-bump joints were obtained with the Cu-mushroom-bump joints. Contact resistance of the Cu-mushroom-bump joints was not dependent upon the thickness of the as-elecroplated Sn-capcoating layer ranging from $1{\mu}m$ to $4{\mu}m$. When the Sn-cap-coating layer was reflowed, however, the contact resistance was greatly affected by the thickness and the reflow time of the Sn-cap-coating layer.