• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.9
• /
• pp.82-90
• /
• 2014

In this paper, a couple of 4-channel differential transimpedance amplifier arrays are realized in a standard 0.18um CMOS technology for the applications of linear LADAR(laser detection and ranging) systems. Each array targets 1.25-Gb/s operations, where the current-mode chip consists of current-mirror input stage, a single-to-differential amplifier, and an output buffer. The input stage exploits the local feedback current-mirror configuration for low input resistance and low noise characteristics. Measurements demonstrate that each channel achieves $69-dB{\Omega}$ transimpedance gain, 2.2-GHz bandwidth, 21.5-pA/sqrt(Hz) average noise current spectral density (corresponding to the optical sensitivity of -20.5-dBm), and the 4-channel total power dissipation of 147.6-mW from a single 1.8-V supply. The measured eye-diagrams confirms wide and clear eye-openings for 1.25-Gb/s operations. Meanwhile, the voltage-mode chip consists of inverter input stage for low noise characteristics, a single-to-differential amplifier, and an output buffer. Test chips reveal that each channel achieves $73-dB{\Omega}$ transimpedance gain, 1.1-GHz bandwidth, 13.2-pA/sqrt(Hz) average noise current spectral density (corresponding to the optical sensitivity of -22.8-dBm), and the 4-channel total power dissipation of 138.4-mW from a single 1.8-V supply. The measured eye-diagrams confirms wide and clear eye-openings for 1.25-Gb/s operations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.1
• /
• pp.14-21
• /
• 2011

A 10b 500MS/s $0.13{\mu}m$ CMOS ADC is proposed for 4G wireless communication systems such as a LTE-Advanced and SDR The ADC employs a calibration-free single-channel folding architecture for low power consumption and high speed conversion rate. In order to overcome the disadvantage of high folding rate, at the fine 7b ADC, a cascaded folding-interpolating technique is proposed. Further, a folding amplifier with the folded cascode output stage is also discussed in the block of folding bus, to improve the bandwidth limitation and voltage gain by parasitic capacitances. The chip has been fabricated with $0.13{\mu}m$ 1P6M CMOS technology, the effective chip area is $1.5mm^2$. The measured results of INL and DNL are within 2.95LSB and l.24LSB at 10b resolution, respectively. The SNDR is 54.8dB and SFDR is 63.4dBc when the input frequency is 9.27MHz at sampling frequency of 500MHz. The ADC consumes 150mW($300{\mu}W/MS/s$) including peripheral circuits at 500MS/s and 1.2V(1.5V) power supply.

• Journal of IKEEE
• /
• v.27 no.1
• /
• pp.45-52
• /
• 2023

Cold-junction correction(CJC) and disconnection detection circuit design of various thermocouples(TC) and multi-channel TC interface circuit using them were designed. The CJC and disconnection detection circuit consists of a CJC semiconductor device, an instrumentation amplifier(IA), two resistors and a diode for disconnection detection. Based on the basic circuit, a multi-channel interface circuit was also implemented. The CJC was implemented using compensation semiconductor and IA, and disconnection detection was detected by using two resistor and a diode so that IA input voltage became -0.42V. As a result of the experiment using R-type TC, the error of the designed circuit was reduced from 0.14mV to 3㎶ after CJC in the temperature range of 0℃ to 1400℃. In addition, it was confirmed that the output voltage of IA was saturated from 88mV to -14.2V when TC was disconnected from normal. The output voltage of the designed circuit was 0V to 10V in the temperature range of 0℃ to 1400℃. The results of the 4-channel interface experiment using R-type TC were almost identical to the CJC and disconnection detection results for each channel. The implemented multi-channel interface has a feature that can be applied equally to E, J, K, T, R, and S-type TCs by changing the terminals of CJC semiconductor devices and adjusting the IA gain.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1465-1470
• /
• 2006

This paper presents a design of low power CMOS LNA(Low Noise Amplifier) for 2.4 GHz ZigBee applications that is a promising international standard for short area wireless communications. The proposed circuit has been designed using TSMC $0.18{\mu}m$ CMOS process technology and two stage cascade topology by current reuse technique. Two stage cascade amplifiers use the same bias current in the current reused stage which leads to the reduction of the power dissipation. LNA design procedures and the simulation results using ADS(Advanced Design System) are presented in this paper. Simulation results show that the LNA has a extremely low power dissipation of 1.38mW with a supply voltage of 1.0V. This is the lowest value among LNAs ever reported. The LNA also has a maximum gain of 13.38dB, input return loss of -20.37dB, output return loss of -22.48dB and minimum noise figure of 1.13dB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.406-409
• /
• 2003

In this paper, a 4-wavelength optical transceiver system is designed and implemented by using TFF (thin film filter) type OADMs (optical add-drop multiplexers). In this new system, the wavelengths of 1510 nm and 1530 nm are used for uploa and download signals, respectively, as well as the wavelengths of 1550 nm and 1310 nm which have been utilized in a 2-wavelength optical transceiver systems. The 4-wavelength optical module show pass characteristics of -1.6 dBm, -1.7 dBm, -5.6 dBm, -5.8dBm for 1510nm, 1530 nm, 1550 nm, 1570 nm, respectively, with 1.2 dBm of input laser power. The isolation for characteristics of the optical module for all the wavelengths are less than -40dB, which is very acceptable for filed requirements.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.8A
• /
• pp.1252-1258
• /
• 1999

This paper describes a COMS IF transceiver IC for 10-MHz bandwidth wireless local loops. It interfaces between the RF section and the digital MODEM section and performs the IF-to-baseband (Rx) and baseband-to-IF (Tx) frequency conversions. The chip incorporates variable gain amplifiers, phase-locked loops, low pass filters, analog-to-digital and digital-to-analog converters. It has been implemented in a 0.6 -${\mu}{\textrm}{m}$ 2-poly 3-metal CMOS process. The phase-locked loops include voltage-controlled oscillators, dividers, phase detectors, and charge pumps on chip. The only external complonents are the filter and the varactor-tuned LC tank circuit. The chip size is 4 mm $\times$ 4 mm and the total supply current is about 57 mA at 3.3 V.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.6
• /
• pp.427-434
• /
• 2013

In this paper, the design and layout of a 2.5 Gbps arrayed VCSEL driver for optical transceiver having arrayed multi-channel of integrating module is confirmed. In this paper, a 4 channel 2.5 Gbps VCSEL (vertical cavity surface emitting laser) driver array with automatic optical power control is implemented using $0.18{\mu}m$ CMOS process technology that drives a $1550{\mu}m$ high speed VCSEL used in optical transceiver. To enhance the bandwidth of the optical transmitter, active feedback amplifier with negative capacitance compensation is exploited. We report a distinct improvement in bandwidth, voltage gain and operation stability at 2.5Gbps data rate in comparison with existing topology. The 4-CH chip consumes only 140 mW of DC power at a single 1.8V supply under the maximum modulation and bias currents, and occupies the die area of $850{\mu}m{\times}1,690{\mu}m$ excluding bonding pads.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.84-92
• /
• 2000

A GaAs MESFET MMIC transmitter for 2.4 GHz wireless local loop handset is designed and fabricated. The transmitter consists of a double balanced active mixer and a two stage driver amplifier with voltage negative feedback. In particular, a pair of CS-CG(common source-common gate) structure compensates the reduction in dynamic range caused by unbalanced complementary IF input signals. And to suppress the leakage local power at RF port, the mixer is designed by using phase characteristic between the ports of MESFET. At the bias condition of 2.7 V and 55.2 mA, the fabricated MMIC transmitter with chip dimensions of $0.75\times1.75 mm^2$ obtains a measured conversion gain of 38.6 dB, output $P_{idB}$ of 11.6 dBm, and IMD3 at -5 dBm RF output power of -31.3 dBc. This transmitter is well suited for WLL handset.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.299-302
• /
• 2016

In this paper, we designed the stack monitoring system with improved performance. To block the incoming pulse noise to the amplifier, shield and the power supply impedance are reduced and the power circuit is isolated. The control unit is developed with variable high voltage, adaptive gain, offset and threshold in order to match the scintillation detector characteristic to the apparatus. 300-1500V variable high voltage power circuit is configured applicable to various scintillation detector. Stack monitoring system with improved performance guarantee the efficiency and the reliability by considering the characteristic of various scintillation detector. Developed stack monitoring system is evaluated with certified testing equipment and shows excellent performance with respect to the uncertainty of the sensor test results.

• Journal of Biomedical Engineering Research
• /
• v.22 no.6
• /
• pp.503-510
• /
• 2001

In this paper. we describe a 32-channel bioimpedance measurement system It consists of 32 independent constant current sources of 50 kHz sinusoid. The amplitude of each current source can be adjusted using a 12-bit MDAC. After we applied a pattern of injection currents through 32 current injection electrodes. we measured induced boundary voltages using a variable-gain narrow-band instrumentation amplifier. a Phase-sensitive demodulator. and a 12-bit ADC. The system is interfaced to a PC for the control and data acquisition. We used the system to detect anomalies with different resistivity values in a saline Phantom with 290mm diameter The accuracy of the developed system was estimated as 2.42% and we found that anomalies larger than 8mm in diameter can be detected. We Plan to improve the accuracy by using a digital oscillator improved current sources by feedback control, Phase-sensitive A/D conversion. etc. to detect anomalies smaller than 1mm in diameter.