• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.217-222
• /
• 1999

The pick up impurity was studied for preparing the NiCuZn ferrite powder by a ball milling method that usually uses in the industrial ceramic process. The raw materials of NiO, CuO, ZnO, and $Fe_2O_3$ powder were weighted according to various spinel composition and mixed for 18 hrs by a wet ball milling method after that the slurry was followed by spray dried and calcined at $700^{\circ}C$ 3 hrs. The calcined NCZF powder was finally ball milled during 65 hrs as same method. The stainless steel ball and jar are used as mixing and milling equipment and the solid concentration of the slurry was 25 vol%. The impurities, stainless steel pickup, were effected by the composition of raw materials especially iron oxide, nickel oxide in the mixing process and by the rate of calcine of NiCuZn ferrite in final milling process. The empirical equation of stainless steel pickup was driven in the wet ball milling system. Finally, the composition of NiCuZn ferrite could be controlled by the empirical equation.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.1
• /
• pp.23-28
• /
• 2019

The Titanium oxide ($TiO_2$) is an attractive ceramic material which shows non-toxic, high refractive index, catalytic activity and biocompatibility, and can be fabricated at a low cost due to its high chemical stability and large anisotropy. $TiO_2$ nanoparticles have been prepared by sol-gel method. The pH of solution can affect the $TiO_2$ crystallinity during the formation of nanoparticles. The prepared nanoparticles were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction, photoluminescence spectroscopy in order to investigate their structural and photoluminescence properties. Through these analysis, the size of $TiO_2$ nanoparticles were found to be smaller than 5 nm. As the crystallinity of the nanoparticles increased, the emission of PL in the 550 nm region increased. Therefore, luminescence characteristics can be improved by controlling the crystallinity of the $TiO_2$ nanoparticles.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.1
• /
• pp.15-23
• /
• 2024

In order to avoid the high observability due to the cavity resonance or electromagnetic wave leakages from the bridge of a battleship or the cockpit of an aircraft, this paper presents a transparent conductive oxide coated structure to prevent the incoming/outgoing electromagnetic waves. Currently, most of the RCS reduction technologies were focused on radar absorbing material such as paints based on conductive or magnetic materials in the fuselage, and there is not much research on countermeasures for achieving the low observability of materials that required optical transparency in actual weapon systems. In this study, the transmission/reflection and absorption performance of the ITO coated structure according to the change of the surface resistance of the transparent conductor were analyzed. Finally, the relationship between the electromagnetic and optical characteristics was established through fabrication and measurement.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.83-89
• /
• 2020

For the past few decades, as part of efforts to protect the environment where fossil fuels, which have been a key energy resource for mankind, are becoming increasingly depleted and pollution due to industrial development, ecofriendly secondary batteries, hydrogen generating energy devices, energy storage systems, and many other new energy technologies are being developed. Among them, the lithium-ion battery (LIB) is considered to be a next-generation energy device suitable for application as a large-capacity battery and capable of industrial application due to its high energy density and long lifespan. However, considering the growing battery market such as eco-friendly electric vehicles and drones, it is expected that a large amount of battery waste will spill out from some point due to the end of life. In order to prepare for this situation, development of a process for recovering lithium and various valuable metals from waste batteries is required, and at the same time, a plan to recycle them is socially required. In this study, we introduce a nanoscale pattern transfer printing (NTP) process of Li2CO3, a representative anode material for lithium ion batteries, one of the strategic materials for recycling waste batteries. First, Li2CO3 powder was formed by pressing in a vacuum, and a 3-inch sputter target for very pure Li2CO3 thin film deposition was successfully produced through high-temperature sintering. The target was mounted on a sputtering device, and a well-ordered Li2CO3 line pattern with a width of 250 nm was successfully obtained on the Si substrate using the NTP process. In addition, based on the nTP method, the periodic Li2CO3 line patterns were formed on the surfaces of metal, glass, flexible polymer substrates, and even curved goggles. These results are expected to be applied to the thin films of various functional materials used in battery devices in the future, and is also expected to be particularly helpful in improving the performance of lithium-ion battery devices on various substrates.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.9
• /
• pp.702-710
• /
• 2012

Eco-friendly $(Na,K)NbO_3$ (NKN)-based piezoelectric ceramic materials were fabricated by conventional ceramic method for shear mode piezoelectric energy harvesting application. $NKN-LiTaO_3$ (LT) based compositions were adopted for the high $d_{15}{\times}g_{15}$ which is proportional to harvested energy density. The composition $0.935(Na_{0.535}K_{0.485})NbO_3-0.065LiTaO_3$ was found to be lie on the boundary of tetragonal and orthorhombic phases. With reducing Ta content, the dielectric constant decreased gradually while maintaining high $d_{15}$, which resulted in increased $d_{15}{\times}g_{15}$. The composition $0.935(Na_{0.535}K_{0.485})NbO_3-0.065Li(Nb_{0.990}Ta_{0.010})O_3$ was found to possess excellent piezoelectric and electromechanical properties ($d_{15}{\times}g_{15}=29\;pm^2/N$, $d_{15}$ = 417 pC/N, $k_{15}$ = 0.55), and high curie temperature ($T_c=455^{\circ}C$).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.420-425
• /
• 2012

Lead-free piezoelectric ceramic/epoxy composites with '0-3' connectivity were prepared by cold-pressing with a temperature controlled curing method. A ceramic powder with a composition of $(Na_{0.51}K_{0.47}Li_{0.02})(Nb_{0.8}Ta_{0.2})O_3$ was synthesized by a conventional solid state reaction route. The dielectric and piezoelectric properties of ceramic/epoxy composites were characterized as a function of the volume fraction (${\phi}$) of piezoelectric ceramics, which was varied from 70 to 95 vol%. The results indicated that the piezoelectric properties of composites were significantly affected by the volume fraction of ceramics. In terms of the piezoelectric properties, specimens showed the best performance at ${\phi}$= 85 vol%, resulting in the piezoelectric constant $d_{33}$ of 39 pC/N and the figure of merit as a piezoelectric energy harvester ($d_{33}{\cdot}g_{33}$) of 1.24 $pm^2/N$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.258-258
• /
• 2007

KNN계 세라믹스는 $400^{\circ}C$ 이상의 높은 큐리온도와 압전특성을 가져 Pb대체용 소재로 각광을 받고 있고 많은 연구들이 진행중이다. 하지만 potassium의 수분과의 반응성이 강하고 녹는점이 낮아 소결시 K2O의 휘발로 인해 화학양론적인 정확도를 맞추기가 어려운 단점을 가지고 있다. 이러한 단점을 보완하기 위하여 Hot pressing, Hot forging, SPS등 여러 가지 방법을 이용한 연구가 보고되었다. 본 연구에서는 낮은 소결밀도를 향상시키기 위하여 성형압과 성형방법을 달리하여 성형밀도에 따른 소결 밀도와 압전 특성 변화에 대하여 관찰하였다. 넓은 범위의 성형밀도를 얻기 위하여 낮은 성형압을 가할 수 있는 기계적으로 작동하는 press와 높은 성형밀도를 가할 수 있는 유압식 press를 사용하였고, 양산성을 고려하여 일반적인 세라믹 제조공정을 이용하였다.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.172-178
• /
• 2019

This paper has designed, fabricated, and analyzed the passive devices realized using low temperature co-fired ceramic (LTCC) multi layer substrates by dividing into the shrinkage process and the non-shrinkage process. Using two types of ceramic materials with dielectric constant 7 or 40, we have fabricated the same shape of various elements in 2 different processes and compared the characteristics. For the substrate of dielctric constant 40, compared with the shrinkage process which has 17% shrink in the X and Y directions with 36% shrink in the Z direction, the non-shrinkage process has 43% shrink in the Z direction without shrink in the X and Y directions, so high dimensional accuracy and surface flatness can be obtained. The inductances and capacitances of the fabricated elements are estimated from measurement using empirical analysis equations of parameters and implemented as a design library. Depending on the substrate and the process, the inductance and capacitance depending on the turn number of winding and unit area have been measured, and empirical polynomials are proposed to predict element values.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.2
• /
• pp.141-147
• /
• 2024

The measurement of strain under an electric field has been widely employed to comprehend the fundamental principles of electro-mechanical responses in ferroelectric, piezoelectric, and electrostrictive materials. In particular, understanding the strain properties of piezoelectric materials in response to electrical stimulation is crucial for researching and developing components such as piezoelectric actuators, acoustic devices, and ultrasonic generators. This tutorial paper introduces the components and operational principles of the linear variable differential transducer (LVDT), a widely used displacement measurement device in various industries. Additionally, we present the configuration of an experimental setup using LVDT to measure the strain characteristics of ferroelectric, piezoelectric, or electrostrictive materials under the application of an electric field. This paper includes simple measurement results and analyses obtained through the LVDT experimental setup, providing valuable information on research methods for the electro-mechanical interactions of various materials.

• Electrical & Electronic Materials
• /
• v.4 no.2
• /
• pp.150-158
• /
• 1991

본 연구에서는 0.80Pb(F $e_{1}$2/N $b_{1}$2/) $O_{3}$-(0.20-x)Pb(F $e_{2}$3/ $W_{1}$3/) $O_{3-x}$Ba(C $u_{1}$2/ $W_{1}$2/) $O_{3}$ (x=0.01, 0.02, 0.03) 세라믹을 소결온도 및 시간을 각각 860~960[.deg.C], 2시간으로 하여 일반 소성법으로 제작하였다. 시편의 조성비와 소결온도에 따른 구조적, 유전적 특성을 조사하였으며 유전손실 특성의 개선을 위해 조성 0.80Pb(F $e_{1}$2/N $b_{1}$2/) $O_{3}$-0.18Pb (F $e_{2}$3/ $W_{1}$3/) $O_{3}$-0.02Ba(C $u_{1}$2/ $W_{1}$2/) $O_{3}$시편에 Mn $O_{2}$를 0~1.25[wt%]로 첨가한 후 유전특성의 변화를 관찰하였다. Mn $O_{2}$의 첨가량이 증가함에 따라 결정립의 크기와 유전상수는 점차 감소하였다. 소결밀도는 900[.deg.C]에서 소결시킨 시편의 경우 최대값을 나타내었다. Ba(C $u_{1}$2/ $W_{1}$2/) $O_{3}$의 양이 0.01에서 0.03[mol]로 증가함에 따라 상전이온도는 38[.deg.C]에서 2[.deg.C]로 감소하였다. 조성 0.80Pb(F $e_{1}$2/N $b_{1}$2/) $O_{3}$0.18Pb(F $e_{2}$3/ $W_{1}$3/) $O_{3}$-0.02Ba(C $u_{1}$2/ $W_{1}$2/) $O_{3}$에 Mn $O_{2}$가 0.25[wt%] 첨가된 시편의 20[.deg.C]에서의 유전상수는 16,700으로 최대값을 유전손실을 1.28[%]로 최소값을 나타내었다. 또한 모든 시편은 온도 및 주파수에 따라 유전상수가 완만하게 변화하는 유전이완 특성을 나타내었다.다.