• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.110-116
• /
• 2016

This paper describes 1.2-V 5-Gb/s scalable low voltage signaling(SLVS) differential transmitter(TX) with a digital impedance calibration and equalizer. The proposed transmitter consists of a phase-locked loop(PLL) with 4-phase output clock, a 4-to-1 serializer, a regulator, an output driver, and an equalizer driver for improvement of the signal integrity. A pseudo random bit sequence generator is implemented for a built-in self-test. The proposed SLVS transmitter provides the output differential swing level from 80mV to 500mV. The proposed SLVS transmitter is implemented by using a 65-nm CMOS with a 1.2-V supply. The measured peak-to-peak time jitter of the implemented SLVS TX is about 46.67 ps at the data rate of 5Gb/s. Its power consumption is 1.88 mW/Gb/s.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.28-33
• /
• 2008

This paper presents a continuous-time equalizer adopting a clock loss tracking technique for digital display interface. This technique uses bottom hold circuit to detect the incoming clock loss. The generated loss signal is directly fed to equalizer filters, building adaptive feed-forward loops which contribute the stability of the system. The design was done in $0.18{\mu}m$ CMOS technology. Experimental results summarize that eye-width of minimum 0.7UI is achieved until -33dB channel loss at 1.65Gbps. The average power consumption of the equalizer is a maximum 10mW, a very low value in comparison to those of previous researches, and the effective area is $0.127mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.5
• /
• pp.50-57
• /
• 2007

A 5Gbps CMOS　adaptive feed-forward equalizer designed for backplane applications is described. The equalizer has adaptive feedback circuits to control the compensating gain of the equalizing filter, which uses a phase detector in clock recovery circuit to detect ISI (Inter-Symbol Interference) level. This makes the equalizer operate adaptively for a various channel length of backplane environments.

• 한국HCI학회:학술대회논문집
• /
• 2008.02b
• /
• pp.430-435
• /
• 2008

Thanks to the development of IT technology, there have been developed a variety of types of portable music players. IT technology didn't stop there, however. It has gone to developing GUIs (Graphic User Interfaces) to deliver more information to the user. As the function of GUIs has become important, the music players are being required to show characteristics of the sounds they output visually beyond just delivering the sounds through analyzing the information that the sounds contain. To visualize the information of sounds, that is to say, has become substantial. In this process, sound graphic equalizers have been developed in order. The object of this study is to produce a new sound graphic equalizer with new forms of expressing visual images of sounds besides the bar graphs, in which user feedback is possible. This study has devised a new sound visualization form in visually expressing the information of sounds by analyzing their characteristics. This new sound visualization provides a sound graphic equalizer with which the user can select images for the information of the sounds s/he listens. This study suggests a new alternative GUI with which the user can change the form of the outputted images in realtime as communicating with the player.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.7
• /
• pp.61-70
• /
• 2017

In this paper, an Ethernet equalizer that compensates for automotive temperature variations within a broad range is presented. Communications in automotive systems have become increasingly important because of the many electronics in vehicles. Ethernet protocols are a good candidate for automotive communications. However, they should satisfy the AEC-Q100 requirements that stipulate an operational temperature range from -40 to $150^{\circ}C$. This paper proposes an Ethernet equalizer that can recover data up until 100 m length of CAT-5 cable adaptively within a temperature range of -40 to $150^{\circ}C$. To support the wide temperature range, a feedback system is used. The proposed equalizer has a bandwidth of 31.25 MHz with a fully-differential structure and is implemented in a Hynix $0.13{\mu}m$ BCDMOS technology.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.683-688
• /
• 1999

This paper describes design of equalizer chips of the read channel for high-density hard-disk drives. In order to meet increasing need of hard-disk drives, the read channel incorporates various PRML schemes. They require proper equalization to implement the efficient hardware of Viterbi decoders. This paper describes EPR-IV equalization for the read channel and a 200MHz analog FIR filter chip is presented which utilizes the sampled analog signal processing efficiently.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.599-602
• /
• 2010

음악 제작 과정의 마지막 단계는 마스터링이다. 과거의 마스터링은 단순히 컴프레서(Compressor)와 리미터(Limiter)를 이용하여 각 트랙의 오디오 레벨을 일률적으로 매칭시키는 것이었지만, 디지털 장비의 꾸준한 발전으로 많은 마스터링 제작자들은 이퀄라이저(Equalizer)와 컴프레서를 기본으로 리버브(Reverb), 딜레이(Delay), 그리고 디더(Dither)를 이용하여 모든 트랙을 하나의 통일된 분위기로 제작하는 방식으로 진보하고 있다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.244-250
• /
• 2012

This paper describes a 4-Gb/s receiver circuit for a low-swing ground-referenced differential signaling system. The receiver employs a common-gate level-shifter and a continuous linear equalizer which compensates inter-symbol-interference (ISI) and improves voltage and timing margins. A bias circuit maintains the bias current of the level-shifter when the common level of the input signal changes. The receiver is implemented with a low-power 65-nm CMOS technology. When 4-Gb/s 400mVp-p signals are transmitted to the receiver through the channel with the attenuation of -19.7dB, the timing margin based on bit error rate (BER) of $10^{-11}$ is 0.48UI and the power consumption is as low as 0.30mW/Gb/s.

• Journal of Broadcast Engineering
• /
• v.20 no.4
• /
• pp.632-640
• /
• 2015

This paper proposes a new method for fast graphic visualization of accurate frequency response of audio equalizer (EQ). When a logarithmic frequency scale is used, a frequency response in high resolution is required for accurate low-band frequency response. However, the high-resolution frequency response requires a huge amount of computational load, which makes the real-time graphic visualization of frequency response impossible. In order to solve the problem of computational load, the proposed method utilizes a low-resolution virtual frequency response in the mid band. It first computes the virtual frequency response of each filter of EQ in the mid band, and then moves it to the target band so that the result corresponds to the desired filter response. Then, it determines the final frequency response of EQ by combining all filter responses. The experiments confirm that the proposed method provides the frequency response of EQ which has an equivalent shape to that computed in high frequency resolution with huge computational load.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.1
• /
• pp.27-34
• /
• 2002

There is much interest on information communications owing to the rapid development of network and IT(Information Technology). Analog signals are converted into digital signals for information communications. However, it is very difficult to completely erase the distortion induced during the conversion of analog signals such as voices and images into digital signals. Existing audio graphic equalizer requires very complex processes to calculate the gain and coefficients of the higher-order filter which is required to generate natural sound and to satisfy the need of each person. Unfortunately it is uneconomical and very difficult to embed the existing digital audio equalizer in the system because of the complexity of the existing digital audio equalizer for high quality sound. This paper discusses the design of a new digital audio graphic equalizer(DAGEQ) which can improve system performance and the quality of audio sound, and can be embedded in the system. This new DAGEQ is designed so that the gain can be controlled automatically. The automatic control of coefficients and gain empowers real time processing and the improvement of audio quality.