• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.685-690
• /
• 2013

This paper has proposed a multi-channel and wide gain-range baseband circuit blocks for the IEEE 802.15.4g MR-OFDM SUN systems. The proposed baseband circuit blocks consist of two negative-feedback VGAs, an active-RC 5th-order chebyshev low-pass-filter, and a DC-offset cancellation circuit. The proposed baseband circuit blocks provide 1 dB cut-off frequencies of 100 kHz, 200 kHz, 400 kHz, and 600 kHz respectively, and achieve a wide gain-range of +7 dB~+84 dB with 1 dB step. In addition, a DC-offset cancellation circuit has been adopted to mitigate DC-offset problems in direct-conversion receiver. Simulation results show a maximum input differential voltage of $1.5V_{pp}$ and noise figure of 42 dB and 37.6 dB at 5 kHz and 500 kHz, respectively. The proposed I-and Q-path baseband circuits have been implemented in $0.18-{\mu}m$ CMOS technology and consume 17 mW from a 1.8 V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.149-155
• /
• 2015

This paper proposes 5-MS/s 10-bit digital-to-analog converter(DAC) with the improved linearity. The proposed DAC consists of a 10-bit R-2R-based DAC, an output buffer using a differential voltage amplifier with rail-to-rail input range, and a band-gap reference circuit for the bias voltage. The linearity of the 10-bit R-2R DAC is improved as the resistor of 2R is implemented by including the turn-on resistance of an inverter for a switch. The output voltage range of the DAC is determined to be $2/3{\times}VDD$ from an rail-to-rail output voltage range of the R-2R DAC using a differential voltage amplifier in the output buffer. The proposed DAC is implemented using a 1-poly 8-metal 130nm CMOS process with 1.2-V supply. The measured dynamic performance of the implemented DAC are the ENOB of 9.4 bit, SNDR of 58 dB, and SFDR of 63 dBc. The measured DNL and INL are less than +/-0.35 LSB. The area and power consumption of DAC are $642.9{\times}366.6{\mu}m^2$ and 2.95 mW, respectively.

• Journal of Sensor Science and Technology
• /
• v.6 no.3
• /
• pp.194-199
• /
• 1997

When voltage or current gets out of the magnetic sensor as it is, we have often faced the problems such as introduction of noise and loss of voltage. In order to reduce these problems, a 2 drain MAGFET operating in the saturation region and fabricated by CMOS process, the system of I/V converter, VCO with operational amplifier, and V/F conversion circuits with Schmitt Trigger are designed and fabricated in one package. The absolute sensitivity of magnetic sensor shows 1.9 V/T and the product sensitivity is $3.2{\times}10^{4}\;V/A{\cdot}T$. The characteristic of V/F conversion is very stabilized and has the value of 190 kHz/T.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.17 no.4
• /
• pp.45-52
• /
• 1980

In order to eliminate the phase errors caused by the finite GB product of operational amplifiers, novel integnator circuits are proposed. These circuits are characterized by their positive phase error angles and integrator selectivity. The positive sign of the Q and of the circuits compensates the negative selectivity and phase error angles, inherent in the integrated operational amplifiers. Miller inverting intergrator of a biquad circuit realized by Thomas is replaced by the proposed circuit and the band-pass frequency response of the modified biquad network is experimentally analyzed. A considerable improvement is recognized to such extent that the center frequency of the band-pass filter is allowed to be shifted up to 20KHz, which has been infeasible with conventional biquad networks.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.2
• /
• pp.41-51
• /
• 1983

An efficient method for the desist of active filters from doubly terminated lossless ladder type passive filters is presented. This technique is based on the linear transformation of network variables from the voltage-current domain to a new domain for the active realization of the passive networks. The method developed herein applies the linear transformation to a ladder building block which contains both a shunt and a series reactive arm, resulting in the minimization of the number of operational amplifiers required for the active realization. The validity and efficiency of this method are verified by the design of the 8th-order Chebyshev low-pass filter followed by the measurement of its frequency characteristics which fairly agree with the theoretic ones.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.278-283
• /
• 2013

This paper presents a design and fabrication of 0.5 V two stage operational amplifier. The proposed operational amplifier utilizes body-driven differential input stage and self-cascode current mirror structure. Cadence Virtuoso is used for layout and the layout data is verified by LVS through Mentor Calibre. The proposed two stage operational amplifier is fabricated using $0.13{\mu}m$ CMOS process and operation at 0.5 V is confirmed. Measured low frequency small signal gain of operational amplifier is 50 dB, power consumption is $29{\mu}W$ and chip area is $75{\mu}m{\times}90{\mu}m$.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.469-471
• /
• 2008

The charge pump affects the performance of PLL. In designing the charge pump, we need to consider various issues such as current mismatch, charge sharing, feedthrough, charge injection, and leakage current. This paper propose the new charge pump circuit which is improved in terms of the current match over the existing high-speed charge pump. The simple method used for reducing current mismatch is the technique that uses a cascode in order to increase the output resistance of the charge pump. However the method limits the output voltage range of the charge pump. So the method is hard to apply as the supply voltage is lowered. Thus this paper proposes a new charge pump circuit using an op amp instead of the cascode. And the new charge pump circuit has an excellent current matching characteristics over a wide output range.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.77-82
• /
• 2006

Analog channel selection filter is described which is designed for a direct-conversion receiver of a IEEE 802.11a wireless LAN. The channel selection filter is an active-RC fifth-order Chebyshev filter with 10MHz cut-off frequency. Two-stage operational amplifier of the filter employs a current re-using feedforward frequency compensation scheme to minimize the power consumption. The filter has been implemented in a 0.18mm CMOS technology and the experimental results show 20mW power consumption with 1.8V supply voltage and 19dB out-of-band iIP3.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.26 no.5
• /
• pp.368-374
• /
• 2016

This paper presents an experimental study on an electrical circuit model of the TiO2-based nano-wired memristor device for neuromophic applications. The electrical circuit equivalent model of the proposed memristor device consists of several electronics components and some passive devices including operational amplifiers, multipliers, resistors and capacitors. In order to verify the proposed design, both of simulation (using PSPICE) as well as hardware implementation were performed for the analysis of the memristor circuit with time waveforms, frequency spectra, I-V curves and power curves. The gained results from the measured data showed a good agreement with the simulation result that confirm the proposed idea.

• Journal of the Korean Society for Railway
• /
• v.14 no.5
• /
• pp.411-415
• /
• 2011

DC/DC switching power converters are commonly used to generate a regulated DC output voltages with high efficiencies from different DC input sources. The voltage mode DC/DC converter utilizes MOSFET (metal-oxide semiconductor field effect transistor), inductor, and a PWM (pulse-width modulation) controller with oscillator, amplifier, and comparator, etc. to efficiently transfer energy from the input to the output at periodic intervals. The fundamental boost converter and a buck converter containing a switched-mode power supply are studied. In this paper, the electrical characteristics of DC/DC power converters are simulated by program of SPICE, and the PWM controller is implemented to check the operation. In addition, power efficiency is analyzed based on the specification of each component.