• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.6
• /
• pp.533-539
• /
• 2015

In this paper, we designed a reconfigurable mixer for microwave broadband receiver. The proposed mixer using a anti-parallel diode is operated as a fundamental mixer or sub-harmonic mixer with respect to a control voltage. A fundamental mixer with a control voltage show a conversion loss of -10 dB, 1 dB compression point of 2.0 dBm at X-band/ Ku-band. On the other hand, it is performed as a sub-harmonic mixer with a conversion loss of -17 dB, 1 dB compression point of 2.0 dBm at Ka-band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.2
• /
• pp.39-45
• /
• 2004

This paper describes the design and implementation of Serial ATA physical layer and performance measurement. It is composed of tranceiver circuit that has the NRZ data stream with +/-250㎷ voltage level and 1.5Gbps data rate, transmission PLL circuit, clock ＆ data recovery circuit, serializer/deserializer circuit and OOB(Out Of Band) generation/detection circuit. We implement the verification of the silicon chip with 0.18${\mu}{\textrm}{m}$ Standard CMOS process. It can be seen that all of the blocks operate with no errors but the data transfer rate is limited to the 1.28Gbps even this should support 1.5Gbps data transfer rate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.494-500
• /
• 2005

In this paper, optical noise is reduced by a differential detector with an optical fiber coupler in an optical wireless system. An $1\times2$ optical fiber coupler divides the received optical signal by 2 equally, and connects them to the two photodiodes in a differential detector. The output voltage variation due to the abrupt change of optical noise distribution in space disappears because the two photodiodes effectively detect the optical signal at the same point. The signal to noise ratio in a differential detector with a fiber coupler was 8 dB higher than in a single photodiode with an optical filter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.339-346
• /
• 1999

A RF receiver section for INMARSAT-C external mounting unit was designed, fabricated and evaluated. Using a INA-03184, the high gain amplifier consists of matched amplifier type. Active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver section implemented here show 60 dB in gain, 44.83 dBc in a spurious level. The voltage standing wave ratios(VSWR)of input output port are less than 1.8:1, respectively.

• Journal of Korea Multimedia Society
• /
• v.5 no.6
• /
• pp.753-758
• /
• 2002

In this paper, low voltage 3V CMOS programmable gain amplifier(PGA) for using in the transmitter and receiver of ADSL analog front-end is designed. The designed receive PGA is connected with 1.1MHz continuous lowpass fillet and controls the gain from 0dB to 30dB. And also the transmitter PGA is connected with 138KHz lowpass filter and controls the gain from -15dB to 0dB. The gain of All PGAs can be programmed by digital logic circuits and main controller. The designed PGAs are verified using HSPICE simulation with $0.35\mu{m}$ CMOS parameter.

• Journal of Biomedical Engineering Research
• /
• v.7 no.1
• /
• pp.59-66
• /
• 1986

A prototype ultrasound sector B-scanner has been developed where the front-end hardware refers to all the necessary circuits for transmitting the ultrasound pulses into the human body and receiving the reflected echo signals from it. The front-end hardware can generally be divided into three parts, i.e., a pulse generator for insonification, a receiver which is responsible for processing of low-level analog signals, and a steering controller for driving the mechanical sector probe whose functions and design concepts are described in this paper. The front-end hardware is implemented which incorporates the following features: improvement of the axial resolution using a circuit which reduces the ring-down time, flexibility of generating time-gain compensation curve, and adoption of a one-chip microcomputer for generating the rate pulses based on the sensor output waveforms.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.4
• /
• pp.740-749
• /
• 2015

In the visible light (VL) communication based on the conventional LED lights, depending on the increase of the communication range, the signal received at the photodiode of the VL receiver has usually the random distorted and decreased amplitude due to the path loss and fading effects of the VL channel. In order to overcome this problem, we propose, design, and implement the visible light communication circuit based on the comparator threshold voltage, where has a built-in distance compensation function. In addition, the performance of the proposed technique is evaluated and analyzed depending on the distance and communication speed through comparing the proposed VLC system based on the threshold voltage with the conventional one.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.138-143
• /
• 2016

The designed and fabricated millimeter-wave security screening system receives radiation energy from an object and a human body. The imaging system consist of sixteen array antennas, sixteen four-stage LNAs, sixteen detectors, an infrared camera, a CCD camera, reflector, and a focusing lens. This system requires high sensitivity and wide bandwidth to detect the input thermal noise. The LNA module of the system has been measured to have 65.8 dB in average linear gain and 82 GHz~102 GHz in bandwidth to enhance the sensitivity for thermal noise, and to receive it over a wide bandwidth. The detector is used for direct current (DC) output translation of millimeter-wave signals with a zero bias Schottky diode. The lens and front-end of the millimeter-wave sensor are important in the system to detect the input thermal noise signal. The frequency range in the receiving sensitivity of the detectors was 350 to 400 mV/mW at 0 dBm (1 mW) input power. The developed W-band imaging system is effective for detecting and identifying concealed objects such as metal or plastic.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.49-55
• /
• 2013

A high-voltage highly-integrated analog front-end (AFE) IC for medical ultrasound imaging applications is implemented using standard 0.18-${\mu}m$ CMOS process. The proposed AFE IC is composed of a high-voltage (HV) pulser utilizing stacked transistors generating up to 15 Vp-p pulses at 2.6 MHz, a low-voltage low-noise transimpedance preamplifier, and a HV switch for isolation between the transmit and receive parts. The designed IC consumes less than $0.15mm^2$ of core area, making it feasible to be applied for multi-array medical ultrasound imaging systems, including portable handheld applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.7
• /
• pp.1534-1540
• /
• 2005

The direct conversion method is classified into the structure using the mixing technology and six-port scheme. In the view point of complexity and integration the direct conversion method using the six-port scheme is superior to that with mixing technology. Expecially, the six-port direct conversion technology provides the low power consumption and the broad-band characteristic. In this paper, the six-port direct conversion receiver with the branch-line coupler and the ring hybrid coupler is desisted respectively. The performances of the designed six-port schemes are analyzed and the six-port scheme with superior performance characteristics is proposed.