• 한국세라믹학회지
• /
• 제28권3호
• /
• pp.234-242
• /
• 1991

Ti-B system ceramics were prepared by the self-propagating high-temperature synthesis method from the mixture of metal titanium and boron powders The major crystalline phase as a function of boron content was TiB for mixtures containing 0.5 or 1.0mol B, and TiB2 for these containing over 1.3mol B. The combustion mode observed by a high-speed camera was steady-state. The Combustion velocity increased with increasing the boron content. Sintered TiB2 specimen showed the density of 97% of theoretical valve, Vicker's hardness of 2250kg/㎟ for 0.2kg load and three-point-flexure strength of 500MPa.

• 한국결정성장학회지
• /
• 제6권3호
• /
• pp.431-438
• /
• 1996

투과전자현미경을 이용하여 고온가압소결된 $TiB_{2}$의 미세구조를 분석하였다. Ionbeam thinning에 의해서 준비된 박편시편은 육방정계 $TiB_{2}$의 결정학적 이방성에 기인한 특징을 보여주었다. 이들 시편에서 철분 불순물은 결정입 3중점, 결정입계 그리고 결정내에 2차상을 형성하는 것으로 확인되었고, 결정입 3중점이나 결정입계 혹은 matrix에서 유리하게 배향된 결정입에 coherence or semi-coherence한 특징을 나타내었다.

• 한국환경과학회지
• /
• 제12권12호
• /
• pp.1277-1284
• /
• 2003

The photocatalytic oxidation of Rhodamine B (RhB) was studied using immobilized TiO$_2$ and fluidized bed reactor. Immobilized TiO$_2$ onto GF/C was employed as the photocatalyst and a 30 W germicidal lamp was used as the light source and the reactor volume was 4.8 L. The effects of parameters such as the amounts of photocatalyst, initial concentration, initial pH, air flow rate and anion additives (NO$_3$$\^$-/, SO$_4$$\^$2-/, Cl$\^$-/, CO$_3$$\^$2-/) competing for reaction. The results showed that the optimum dosage of the immobilized TiO$_2$ was 40.0 g/L. Initial removal rate of immobilized TiO$_2$ was expressed Langmuir - Hinshelwood equation.

• 한국주조공학회지
• /
• 제9권4호
• /
• pp.320-326
• /
• 1989

Titanium-Boron-Aluminium master alloys are used extensively to grain-refine a wide range of aluminium alloys. This experiment was performed by various amounts of AlTi5B1 addition to the technical aluminium alloys, and also by changing cast temperature and hold time of the melts. The macrostructures were shown that with increasing the addition of AlTi5B1 to the melts, the grain became finer. In the case of cast temperature high enough over $900^{\circ}C$, the grain became coarser, but hold time change not affected on the grain refinement. Particles of $TiAl_3$, and $TiB_2$ were found in the grains and grainboundaries. The important role of grain refinement in this experiment were mainly $TiAl_3$, and also $TiB_2$ those have been confirmed in TEM, SEM, EDS, WDX and X-ray diffraction.

• 전기학회논문지
• /
• 제57권5호
• /
• pp.808-815
• /
• 2008

The composites were fabricated 61[vol.%] ${\beta}$-SiC and 39[vol.%] $TiB_2$ powders with the liquid forming additives of 8, 12, 16[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid by pressureless annealing at 1650[$^{\circ}C$] for 4 hours. The present study investigated the influence of the content of $Al_2O_3+Y_2O_3$ sintering additives on the microstructure, mechanical and electrical properties of the pressureless annealed SiC-$TiB_2$ electroconductive ceramic composites. Reactions between SiC and transition metal $TiB_2$ were not observed in the microstructure and the phase analysis of the pressureless annealed SiC-$TiB_2$ electroconductive ceramic composites. Phase analysis of SiC-$TiB_2$ composites by XRD revealed mostly of ${\alpha}$-SiC(6H), ${\beta}$-SiC(3C), $TiB_2$, and In Situ YAG($Al_2Y_3O_{12}$). The relative density of SiC-$TiB_2$ composites was lowered due to gaseous products of the result of reaction between SiC and $Al_2O_3+Y_2O_3$. There is another reason which pressureless annealed temperature 1650[$^{\circ}C$] is lower $300{\sim}450[^{\circ}C]$ than applied pressure sintering temperature $1950{\sim}2100[^{\circ}C]$. The relative density, the flexural strength, the Young's modulus and the Vicker's hardness showed the highest value of 82.29[%], 189.5[Mpa], 54.60[Gpa] and 2.84[Gpa] for SiC-$TiB_2$ composites added with 16[wt%] $Al_2O_3+Y_2O_3$ additives at room temperature. Abnormal grain growth takes place during phase transformation from ${\beta}$-SiC into ${\alpha}$-SiC was correlated with In Situ YAG phase by reaction between $Al_2O_3$ and $Y_2O_3$ additive during sintering. The electrical resistivity showed the lowest value of 0.0117[${\Omega}{\cdot}cm$] for 16[wt%] $Al_2O_3+Y_2O_3$ additives at 25[$^{\circ}C$]. The electrical resistivity was all negative temperature coefficient resistance (NTCR) in the temperature ranges from $25^{\circ}C$ to 700[$^{\circ}C$]. The resistance temperature coefficient of composite showed the lowest value of $-2.3{\times}10^{-3}[^{\circ}C]^{-1}$ for 16[wt%] additives in the temperature ranges from 25[$^{\circ}C$] to 100[$^{\circ}C$].

• 한국주조공학회지
• /
• 제30권4호
• /
• pp.147-150
• /
• 2010

알루미늄 합금의 미세조직 개량을 위한 목적으로 사용되는 Al-Ti-B 합금계의 미세화제는 재활용 과정에서 붕소(B)의 농축(Agglomeration) 문제 및 Zr, Si, Cr 등을 함유하는 합금에서 미세화 효과가 급격히 감소하는 Poisoning effect 등이 지적되어 왔다. 최근에는 이를 대체할 수 있는 Al-Ti-C 합금계의 미세화제에 대한 연구가 활발한데 이는 TiC가 용탕 내에서 ${\alpha}$-Al의 핵생성처로 직접 작용하는 점에 착안한 것이다. 한편, 이들 Al-Ti-B, Al-Ti-C 계의 미세화제는 그 제조공정에서 $K_2TiF_6$를 이용함에 따라 불소함유 유해가스를 배출하여 환경 문제를 야기하고, 이를 포집/정화하기 위한 추가설비를 요구하게 된다. 따라서 대기 환경 오염 및 경제성 측면에서 유리한 미세화제의 친환경 제조기술에 대한 개발이 필요한 시점이다. 본 연구에서는 $K_2TiF_6$를 사용하지 않고 용탕 내의 자발적 반응을 이용하여 환경 및 경제적 측면에서 유리한 Al-Ti-C 미세화제를 개발하고자 하였다. A3003 합금을 대상소재로 하여 개발된 Al-Ti-C 미세화제와 상용 Al-Ti-B 미세화제의 미세화 도달시간 및 fading 발생 등을 비교하였다. 본 연구를 통하여 개발된 Al-8.6Ti-0.025C 미세화제는 상용 Al-Ti-B 미세화제 보다 적은 첨가량에도 유사한 미세화 성능을 나타내었으며 용탕 유지시간 100분까지도 fading이 발생하지 않는 것을 확인하였다.

• Rapid Communication in Photoscience
• /
• 제4권1호
• /
• pp.9-11
• /
• 2015

The debromination of phenethyl bromide by the $B_{12}-TiO_2$ hybrid catalyst under UV light irradiation was investigated. The catalytic efficiency was dependent on the type of $TiO_2$. The anatase form of $TiO_2$ was superior to the rutile form of $TiO_2$. The selectivity of the product was also dependent on the crystal structure of $TiO_2$, and the rutile form of $TiO_2$ showed a high selectivity for the formation of the coupling product, 2,3-diphenylbutane, when compared to that of the anatase form of $TiO_2$.

• 열처리공학회지
• /
• 제21권1호
• /
• pp.26-32
• /
• 2008

Effects of annealing treatment on microstructure and mechanical property of co-sputtered TiNi thin films were studied. As-deposited films showed amorphous state. However, above annealing temperature of $500^{\circ}C$ martensite phase (B19'), precipitate phase ($Ti_2Ni$) and a small amount of parent phase ($B_2$) were present, and phase transformation behaviors were three multi-step phase transformations $B19^{\prime}{\rightarrow}B_2$ and $B_2{\rightarrow}R-phase$ and $R-phase{\rightarrow}B19^{\prime}$. Increase of martensite transformation temperature, increase of microhardness and Young's modulus of TiNi films annealed above $500^{\circ}C$ were discussed in terms of precipitate phase.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.191-193
• /
• 2004

The composites were fabricated, respectively, using 61vol.% SiC-39vol.% $TiB_2$ and using 61vol.% SiC-39vol.% $ZrB_2$ powders with the liquid forming additives of 12wt% $Al_2O_3+Y_2O_3$ by hot pressing annealing at $1650^{\circ}C$ for 4 hours. Reactions between SiC and transition metal $TiB_2$, $ZrB_2$ were not observed in this microstructure. The result of phase analysis of composites by XRD revealed SiC(6H, 3C), $TiB_2$, $ZrB_2$ and $YAG(Al_5Y_3O_{12})$ crystal phase on the SiC-$TiB_2$, and SiC-$ZrB_2$ composites. The ${\beta}\;{\alpha}$-SiC phase transformation was occurred on the $SiC-TiB_2$, $SiC-ZrB_2$ composites. The relative density, the flexural strength and Young's modulus showed respectively value of 98.57%, 226.06Mpa and $86.37{\times}10^3Mpa$ in SiC-$ZrB_2$ composites.

• 소성∙가공
• /
• 제8권3호
• /
• pp.319-319
• /
• 1999

From isothermal and cyclic oxidation tests on thermomechanically treated Ti-5%Al, Ti47%Al-4%Cr, and Ti-48%Al-2%Cr-2%Nb alloys at 800, 900, 1000℃ in air, it was found that Ti-48%Al-2%Cr-2%Nb and Ti-47%Al-4%Cr had the best and the worst oxidation resistance, respectively. The oxide scales consisted primarily of TiO₂and Al₂O₃, with and without a small amount of dissolved Cr and 7b ions, depending on the alloy composition. These ions were slightly enriched inside the inner oxide layer, and strongly enriched around the scale-matrix interface. The outer TiO₂-rich layer was formed by the outward diffusion of Ti ions, while the inner (TiO₂+A1₂O₃,) mixed layer was formed by the inward transport of oxygen. The outward movement of Al ions farmed the intermediate Al₂O₃-rich Iayer, above talc prepared alloys.