• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.258-261
• /
• 2000

Highly (h00)-oriented (Ba, Sr)TiO$_3$(BST) thin films were grown by pulsed laser deposition on the perovskite LaNiO$_3$(LNO) metallic oxide layer as a bottom electrode. The LNO films were deposited on SiO$_2$/Si substrates by rf-magnetron sputtering method. The crystalline phases of the BST film were characterized by x-ray $\theta$-2$\theta$, $\omega$-rocking curve and $\psi$-scan diffraction measurements. The surface microsturcture observed by scanning electron microscopy was very dense and smooth. The low-frequency dielectric responses of the BST films grown at various substrate temperatures were measured as a function of frequency in the frequency range from 0.1 Hz to 10 MHz. The BST films have the dielectric constant of 265 at 1 kHz and showed multiple dielectric relaxation at the low frequency region. The origin of these low-frequency dielectric relaxation are attributed to the ionized space charge carriers such as the oxygen vacancies and defects in BST film, the interfacial polarization in the grain boundary region and the electrode polarization. We studied also on the capacitance-voltage characteristics of BST films.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.2
• /
• pp.60-66
• /
• 2001

($Ba_x$$Sr_{1-x}$)$TiO_3$ (x=0.9, 0.7, 0.5) thin films were prepared on ITO-coated glass by sol-gel method. Perovskite phase formation temperature of BST thin films seemed to be higher than $600^{\circ}C$. Peaks of perovskite phase shift to high diffraction angles as the Sr/(Ba+Sr) ratio was increased, due to the smaller ionic size of $Sr^{2+}$ than $Ba^{2+}$ . As a heating temperature was increased, the grain became coarser. And as Sr/(Ba + Sr) ratio was increased, the grain became finer. Dielectric constants of the BST(50/50) thin film are higher and dielectric losses of that are lower than those of the others. Dielectric constant and dielectric loss of the BST(50/50) thin film were 652 and 0.042 at 1kHz, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.996-1002
• /
• 2000

Ferroelectric (Ba, Sr) TiO$_3$(BST) thin films have attracted much attention for use in new capacitor materials of dynamic random access memories (DRAMs). In order to apply BST to the DRAMs, the etching process for BST thin film with high etch rate and vertical profile must be developed. However, the former studies have the problem of low etch rate. In this study, in order to increase the etch rate, BST thin films were etched with a magnetically enhanced inductively coupled plasma(MEICP) that have much higher plasma density than RIE (reactive ion etching) and ICP (inductively coupled plasma). Experiment was done by varying the etching parameters such as CF$_4$/(CF$_4$+Ar) gas mixing ratio, rf power, dc bias voltage and chamber pressure. The maximum etch rate of the BST films was 170nm/min under CF$_4$/CF$_4$+Ar) of 0.1, 600 W/-350 V and 5 mTorr. The selectivities of BST to Pt and PR were 0.6 and 0.7, respectively. Chemical reaction and residue of the etched surface were investigated with X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS).

• The Korean Journal of Ceramics
• /
• v.2 no.2
• /
• pp.95-101
• /
• 1996

Variations of the leakage current behaviors and interface potential barrier $({\Phi}_B)$ of rf-sputter deposited (Ba, Sr)$TiO_3$ (BST) thin films with thicknesses ranging from 20 nm to 150nm are investigated as a function of the thickness and bias voltages. The top and bottom electrodes are dc-sputter-deposited Pt films. ${\Phi}_B$ critically depends on the BST film deposition temperature, postannealing atmosphere and time after the annealing. The postannealing under $N_2$ atmosphere results in a high interface potential barrier height and low leakage current. Maintaining the BST capacitor in air for a long time reduces the ${\Phi}_B$ from about 2.4 eV to 1.6 eV due to the oxidation. ${\Phi}_B$ is not so dependent on the film thickness in this experimental range. The leakage conduction mechanism is very dependent on the BST film thickness; the 20 nm thick film shows tunneling current, 30 and 40 nm thick films show Shottky emission current.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.6-12
• /
• 1995

High Tc superconducting YBa$_{2}$Cu$_{3}$$O_{7-x}$ thin films were prepared on various substrates by off-axis rf magnetron sputtering method to examine the substrate effects on the film structure and its R-T characteristics. The SEM analysis showed that the surface morphology of the grown YBa$_{2}$Cu$_{3}$O.sub 7-x/, film has different characteristic structure with different substrate used. The film on (100) SrTiO$_{3}$ substrate has critical current density of 3*10$^{5}$ A/cm$^{2}$ at 77K under zero magnetic field. The X-ray diffraction measurements revealed that the films on (100) SrTiO$_{3}$ substrate have mixed a-axis and c-axis normal to the substrate surface and the films on (100) MgO and ZrO$_{2}$/sapphire substrates have c-axis normal orientation to the substrate surface. However, YBa$_{2}$Cu$_{3}$$O_{7-x}$ films on (100) sapphire substrates showed no preferential orientation.ion.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.3
• /
• pp.128-132
• /
• 2004

The perovskite ferroelectric materials of the PZT, SBT and BST series will attract much attention for application to ULSI devices. Among these materials, the BST ($Ba_0.6$$Sr_0.4$/$TiO_3$) is widely considered the most promising for use as an insulator in the capacitors of DRAMS beyond 1 Gbit and high density FRAMS. Especially, BST thin films have a good thermal-chemical stability, insulating effect and variety of Phases. However, BST thin films have problems of the aging effect and mismatch between the BST thin film and electrode. Also, due to the high defect density and surface roughness at grain boundarys and in the grains, which degrades the device performances. In order to overcome these weakness, we first applied the chemical mechanical polishing (CMP) process to the polishing of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. BST ferroelectric film was fabricated by the sol-gel method. And then, we compared the surface characteristics before and after CMP process of BST films. We expect that our results will be useful promise of global planarization for FRAM application in the near future.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.2
• /
• pp.56-62
• /
• 2003

Epitaxial $Bi_4Ti_3O_{12}$ films on $SrTiO_3$(100), L$aA1O_3$(100) and MgO(100) were prepared by sol-gel process using metal naphthenate as a starting material. As-deposited films were pyrolyzed at $500^{\circ}C$ for 10 min In air and annealed at $750^{\circ}C$ for 30 min in air. Crystallinity and in-plane alignment of the film were investigated by X-ray diffraction $\theta$-2$\theta$ scan and P scanning. A field emission-scanning electron microscope and an atomic force microscope were used for characterizing the surface morphology and the surface roughness of the film. The film prepared on MgO(100) showed the most poor crystallinity and in-plane alignment, compared to those on the other substrates. While the films on $LaA1O_3$(100) and $SrTiO_3$(100) having high crystallinity and in-plane alignment showed the form of columnar grain growth, the film on MgO(100) which had poor crystallinity showed the form of acicula grain growth.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.1
• /
• pp.13-17
• /
• 2005

The Pb(Zr/sub 0.52/Ti/sub 0.48/)O₃/(Ba/sub 0.6/Sr/sub 0.4/)TiO₃[PZT/BST] heterolayered thin films were deposited on Pt/Ti/SiO₂/Si substrates by using the RF sputtering method with different RF power. The PZT/BST heterolayered thin films had the tetragonal structure of the PZT phase and BST phase. Increasing the RF power. the intensity of the PZT (100), (110) peaks and BST (111) peaks were decreased and the intensity of the BST (100), (110) peaks were increased. The thickness ratio of the top layered BST thin film and the bottom layered PZT thin film was 2 to1. The atomic concentration of the Ba, Sr, Pb. Zr, Ti atoms were constant in the PZT thin films and BST thin films, respectively. The Pt atom was diffused to the PZT region in the PZT/BST heterolayered thin films deposited at condition of 60[W] RF power. Increasing the frequency, dielectric constant and loss of the PZT/BST heterolayered thin films were decreased. The dielectric constant and loss of the PZT/BST heterolayered thin films deposited with RF power of 90[W] were 406 and 3%, respectively.

• Korean Journal of Materials Research
• /
• v.6 no.5
• /
• pp.449-456
• /
• 1996

BaO, SrCI2.6H2O 그리고 Ti(OPri)4를 출발 원료로 사용하여 균일한 BaxSr1-xTiO3(BST) 솔을 합성하였고, BST 박막을 회전 코팅 법으로 Si 및 Pt/Ti/SiO2/Si 기판위에 제조하였다. 적외선 및 NMR 스펙트럼 분석으로 킬레이션 조제로 사용한 acetylacetone(AcAc)이 엔올 형태로 Ti-알콕사이드와 결합하여 솔 안정화에 기여함을 확인하였다. Xedrogel에 대한 DT/TGA 및 적외선 스펙트럼 결과로부터 페로브스카이트 상생성이 $600^{\circ}C$ 이상에서 이루어짐을 관찰하였다. $700^{\circ}C$에서 열처리한 박마은 -300(10 KHz)의 상대유전율을 나타내었고, 결정립의 저항 및 입계의 병렬 RC 성분으로 등가회로를 구성할 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.31-34
• /
• 2006

In this study, $(Ba_{0.7}\;Sr_{0.3})TiO_3$ was coated on Pt/Ti/$SiO_2$/Si wafer by using Sol-Gel method. Coating process was repeated 3~5 times and then sintered at 750[$^{\circ}C$] for 1 hour. Each specimen was analyzed structure and electrical characteristics. In structure characteristics, EDX analyzed the samples ratio of the formation on the structural property. Thermal behavior was observed with TG-DTA and concluded that the heat-treatment of the samples was degreed 750[$^{\circ}C$]. Surface and section of thin films were observed with SEM.