• 한국재료학회지
• /
• 제29권9호
• /
• pp.553-558
• /
• 2019

$Cu_2ZnSn(S,Se)_4(CZTSSe)$ thin film solar cells areone of the most promising candidates for photovoltaic devices due to their earth-abundant composition, high absorption coefficient and appropriate band gap. The sputtering process is the main challenge to achieving high efficiency of CZTSSe solar cells for industrialization. In this study, we fabricated CZTSSe absorbers on Mo coated soda lime glass using different pressures during the annealing process. As an environmental strategy, the annealing process is performed with S and Se powder, without any toxic $H_2Se$ and/or $H_2S$ gases. Because CZTSSe thin films have a very narrow stable phase region, it is important to control the condition of the annealing process to achieve high efficiency of the solar cell. To identify the effect of process pressure during the sulfo-selenization, we experiment with varying initial pressure from 600 Torr to 800 Torr. We fabricate a CZTSSe thin film solar cell with 8.24 % efficiency, with 435 mV for open circuit voltage($V_{OC}$) and $36.98mA/cm^2$ for short circuit current density($J_{SC}$), under a highest process pressure of 800 Torr.

• 한국재료학회지
• /
• 제23권11호
• /
• pp.613-619
• /
• 2013

$Cu_2ZnSn(S_x,Se_{1-x})_4$ (CZTSSe) thin films were prepared by sulfurization of evaporated precursor thin films. Precursor was prepared using evaporation method at room temperature. The sulfurization was carried out in a graphite box with S powder at different temperatures. The temperatures were varied in a four step process from $520^{\circ}C$ to $580^{\circ}C$. The effects of the sulfurization temperature on the micro-structural, morphological, and compositional properties of the CZTSSe thin films were investigated using X-ray diffraction (XRD), Raman spectra, field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The XRD and Raman results showed that the sulfurized thin films had a single kesterite crystal CZTSSe. From the FE-SEM and TEM results, the $Mo(S_x,Se_{1-x})_2$ (MoSSe) interfacial layers of the sulfurized CZTS thin films were observed and their thickness was seen to increase with increasing sulfurization temperature. The microstructures of the CZTSSe thin films were strongly related to the sulfurization temperatures. The voids in the CZTSSe thin films increased with the increasing sulfurization temperature.

• 한국재료학회지
• /
• 제30권6호
• /
• pp.285-291
• /
• 2020

Recent advances in technology using ultra-thin noble metal film in oxide/metal/oxide structures have attracted attention because this material is a promising alternative to meet the needs of transparent conduction electrodes (TCE). AZO/Ag/AZO multilayer films are prepared by magnetron sputtering for Cu₂ZnSn(S,Se)₄ (CZTSSe) of kesterite solar cells. It is shown that the electrical and optical properties of the AZO/Ag/AZO multilayer films can be improved by the very low resistivity and surface plasmon effects due to the deposition of different thicknesses of Ag layer between oxide layers fixed at AZO 30 nm. The AZO/Ag/AZO multilayer films of Ag 15 nm show high mobility of 26.4 ㎠/Vs and low resistivity and sheet resistance of 3.58^⁎10^-5 Ωcm and 5.0 Ω/sq. Also, the AZO/Ag (15 nm)/AZO multilayer film shows relatively high transmittance of more than 65 % in the visible region. Through this, we fabricated CZTSSe thin film solar cells with 7.51 % efficiency by improving the short-circuit current density and fill factor to 27.7 mV/㎠ and 62 %, respectively.

• 한국재료학회지
• /
• 제22권5호
• /
• pp.259-273
• /
• 2012

Chalcogenide-based semiconductors, such as $CuInSe_2$, $CuGaSe_2$, Cu(In,Ga)$Se_2$ (CIGS), and CdTe have attracted considerable interest as efficient materials in thin film solar cells (TFSCs). Currently, CIGS and CdTe TFSCs have demonstrated the highest power conversion efficiency (PCE) of over 11% in module production. However, commercialized CIGS and CdTe TFSCs have some limitations due to the scarcity of In, Ga, and Te and the environmental issues associated with Cd and Se. Recently, kesterite CZTS, which is one of the In- and Ga- free absorber materials, has been attracted considerable attention as a new candidate for use as an absorber material in thin film solar cells. The CZTS-based absorber material has outstanding characteristics such as band gap energy of 1.0 eV to 1.5 eV, high absorption coefficient on the order of $10^4cm^{-1}$, and high theoretical conversion efficiency of 32.2% in thin film solar cells. Despite these promising characteristics, research into CZTS-based thin film solar cells is still incomprehensive and related reports are quite few compared to those for CIGS thin film solar cells, which show high efficiency of over 20%. The recent development of kesterite-based CZTS thin film solar cells is summarized in this work. The new challenges for enhanced performance in CZTS thin films are examined and prospective issues are addressed as well.

• 한국재료학회지
• /
• 제7권10호
• /
• pp.856-862
• /
• 1997

박막형 CdTe/CdS 태양전지의 배면전극(back contacts)물질로서 Cu도핑된 ZnTe 박막(ZnTe:Cu)을 전착법(electroplating)으로 제조하는 연구를 수행하였다. Sulfate계의 전해질 수용액에서 CdTe 기판과 투명전극으로 코팅된 유리(In$_{2}$O$_{3}$: Sn, ITO)기판 위에 ZnTe 박막을 코팅하는 방법으로써 potentiostat와 기판(cathode), Pt counter electrode, Ag/AgCI 표준전극으로 구성된 장치를 사용하여 pH=2.5-4, T=70-8$0^{\circ}C$, 0.02M $Zn^{2+}$ 1x$10^{-4}$M TeO$_{2}$, 0.2M $K_{2}$SO$_{4}$조건에서 -0.800 Vs~-0.975 V 범위의 전압(V$_{a}$ )에 걸쳐 실험하였다. ITO박막을 기판으로 사용하여 cyclic voltammogram을 작성한 결과 약 -0.50 V 에서 Te환원 peak이 나타났다. Auger electron spectroscopy (AES)로 조성분석한 결과 표면에서 Zn signal이 강하게 나왔고 시편의 두께에 따라 Zn의 signal감소하는 반면 Cd signal은 증가하는 것이 확인되었다. SEM 사진으로부터 ZnTe의 표면이 작은 입자 (0.2$\mu\textrm{m}$ 이하)로 구성되어 있으며 낮은 V$_{a}$ 에서는 입자가 작아지면서 조직이 치밀해짐이 관찰되었다. Optical transmission방법에 의하여 ITO기판위에 입혀진 박막의 밴드갭은 2.5 eV으로 측정되었다. 수용액중의 Cu$_{2+}$와 triethanolamine(TEA)은 산성용액에서 착물형성이 이루어지지 않았으며 1,10-phenanthroline과는 pH=2에서도 착물이 형성되었다.

• 한국재료학회지
• /
• 제32권11호
• /
• pp.481-488
• /
• 2022

The Cu₂ZnSn(S_xSe_1-x)₄ (CZTSSe) absorbers are promising thin film solar cells (TFSCs) materials, to replace existing Cu(In,Ga)Se₂ (CIGS) and CdTe photovoltaic technology. However, the best reported efficiency for a CZTSSe device, of 13.6 %, is still too low for commercial use. Recently, partially replacing the Zn²⁺ element with a Cd²⁺element has attracting attention as one of the promising strategies for improving the photovoltaic characteristics of the CZTSSe TFSCs. Cd²⁺ elements are known to improve the grain size of the CZTSSe absorber thin films and improve optoelectronic properties by suppressing potential defects, causing short-circuit current (J_sc) loss. In this study, the structural, compositional, and morphological characteristics of CZTSSe and CZCTSSe thin films were investigated using X-ray diffraction (XRD), X-ray fluorescence spectrometer (XRF), and Field-emission scanning electron microscopy (FE-SEM), respectively. The FE-SEM images revealed that the grain size improved with increasing Cd²⁺ alloying in the CZTSSe thin films. Moreover, there was a slight decrease in small grain distribution as well as voids near the CZTSSe/Mo interface after Cd²⁺ alloying. The solar cells prepared using the most promising CZTSSe absorber thin films with Cd²⁺ alloying (8 min. 30 sec.) exhibited a power conversion efficiency (PCE) of 9.33 %, J_sc of 34.0 mA/cm², and fill factor (FF) of 62.7 %, respectively.

• 자원환경지질
• /
• 제19권spc호
• /
• pp.121-130
• /
• 1986

In the Janggun mine, stannite occurs as anhedral grains, up to 500 micrometer in long dimension, closely associated with sphalerite, chalcopyrite, arsenopyrite, pyrrhotite, galena and rhodochrosite in the periphery of the South ore body. In reflected light, stannite is grayish yellow green in color and exhibits moderate bireflectance and strong anisotropism without any intenal reflections. Reflection; Rmax. =29.0, Rmin. =27.8 percent at a wavelength of 560nm, and VHN; 219~244kg/mm at a 50g load. The chemical composition on the average from 35 spot analyses by electron microprobe is, Cu 28.0, Fe 12.7, Zn 2.9, Mn 0.2, Sn 25.8, S 30.3, sum 99.9 (all in weight percent); the corresponding chemical formula as calculated on the basis of total atoms=8 is, Cu 1.88 Fe 0.97 Zn 0.19 Mn 0.02 Sn 0.93 S 4.01, which fulfills approximately the ideal formula of $Cu_2FeSnS_4$. The strongest reflections on the X-ray diffraction patterns are; $3.10{\AA}$ (10) (112), $2.72{\AA}$ (5) (020, 004), $1.922{\AA}$ (5) (024), $1.642{\AA}$ (3) (132), $1.244{\AA}$ (3) (143, 136, 235), $1.111{\AA}$(3) (244), $0.958{\AA}$ (1) (048, 422), the patterns are identical with those of literature. From the textural evidence of the microscopic observation, the mineral is considered to have been formed at the middle stage of hydrothermal lead-zinc-silver mineralization.

• 헤리티지:역사와 과학
• /
• 제54권2호
• /
• pp.22-37
• /
• 2021

풍탁은 한국, 중국, 일본에서 오랜 기간 사용되고 있는 불교 장엄구이다. 하지만 풍탁은 제작 시기를 추정하는 데 어려움이 있으며 유물의 수가 많지 않아 기초연구가 부족한 실정이다. 그러므로 본 연구에서는 미술사적 연구를 참고하여 논산 관촉사 석조미륵보살입상의 보개에 장식되어 있는 청동풍탁 8점을 형태학적으로 분류하였으며, 이에 따른 제작 기법 및 제작 시기에 대하여 과학적으로 규명하였다. 연구 결과를 종합해볼 때 보개의 위치에 따라 관촉사 석조미륵보살입상 청동풍탁은 형태 및 제작 기법의 특징이 나타났다. 대형인 하부 보개 청동풍탁 4점은 Cu-Sn-Pb 삼원계 합금을 주조 기법으로 제작하였으며, 서산 출토 동제풍탁과 형태가 매우 흡사하여 고려 전기에 조성된 것으로 확인된다. 중형인 상부 보개 북측 청동풍탁 2점은 Cu-Sn 또는 Cu-Sn-Pb 합금을 단조 기법으로 제작하였으며, 고려 후기~조선시대에 나타나는 원통형 풍탁과 형태가 유사하다. 소형인 상부 보개 남측 청동풍탁 2점은 미량의 아연(Zn)이 존재하는 것으로 판단되는 Cu-Sn-Pb 삼원계 합금을 주조 기법으로 제작하였으며, 합금 성분 및 치게의 형태 등을 통해 조선 후기에 제작된 것으로 보인다. 미세조직 관찰 및 성분 분석을 통해 하부 보개 청동풍탁 2점은 Cu:Sn:Pb≒80:15:5의 합금비를 지닌 삼원계 합금을 주조 후 서냉하여 제작하였음을 알 수 있다. 상부 보개 동북측 청동풍탁은 방짜유기와 유사한 합금비인 Cu-Sn 이원계 합금을 소재로 단조 기법으로 제작된 것으로 확인된다. 이를 국내 풍탁의 선행 연구와 비교·분석한 결과, 하부 보개 동측 청동풍탁 2점은 타명기에 적합한 주석 함유량을 지닌 고려시대에 제작된 강진 월남사지 출토 금동풍탁의 합금 조성비와 유사하게 확인된다. 방짜유기와 유사한 합금비를 지닌 상부 보개 동북측 청동풍탁은 현재까지 연구된 풍탁 중 유일하게 단조 기법으로 제작된 사례이다. 본 연구를 통해 풍탁의 제작 시기를 형태학적 특징으로 구분하는 데 있어 과학적인 근거를 통해 보다 명확하게 구분할 수 있는 기초자료를 제공하고자 하였다.

• Bulletin of the Korean Chemical Society
• /
• 제20권3호
• /
• pp.352-354
• /
• 1999

The spectrophotometric determination of Cu(Ⅱ) with α-(2-benzimidazolyl)-α',α"-(N-5-nitro-2-pyridylhydrazone)-toluene has been investigated. The optimum conditions of pH, stability, concentration of ligand and surfactant were evaluated. This method is a simple and sensitive method for determination of Cu(Ⅱ) and offers a selective separation of Cu(Ⅱ) from sample solution containin- I ppm below amount of Ni(Ⅱ), Co(Ⅱ), Zn(Ⅱ) and Sn(Ⅱ). Copper was determined by measuring the absorbance of Cu(Ⅱ)-BINPHT complex extracted with benzene in Brij 58 surfactant at 410 nm. Beer's law is obeyed over the concentration range 0∼2.5 μgmL-1 and the detection limit (S/N=2) is 0.06 μgmL-1. The relative standard deviation at the 0.3 μgmL-1 is 2.4% (N=7). The method was applied for the determination of Cu(Ⅱ) in various milks.

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.1-26
• /
• 1994

The purpose of this study was to investigate the dissolution components during corrosion of amalgams and to identify surface corrosion products in the modified Fusayama artificial saliva. Four type of amalgam alloys were used: low copper lathe cut amalgam alloy (Cavex 68), low copper spherical amalgam alloy (Caulk Spherical Alloy), high copper admixed amalgam alloy (Dispersalloy) and high copper single composition amalgam alloy (Tytin). Each amalgam alloy and Hg were triturated according to the manufacturer's direction by means of mechanical amalgamator (Capmaster, S.S.White), and then the triturated mass was inserted into the cylindrical metal mold which was 10mm in diameter and 2.0mm in height and condensed with compression of 150kg/$cm^2$ using oil pressor. The specimens were removed from the mold and stored at room temperature for 7 days and cleansed with distiled water for 30 minutes in an ultrasonic cleaner. The specimens were immersed in the modified Fusayama artificial saliva for the periods of 1 month, 3 months and 6 months. The amounts of Hg, Cu, Sn and Zn dissolved from each amalgam specimen immersed in the artificial saliva for the periods of 1 month, 3 months and 6 months were measured using Inductivity Coupled Plasma Atomic Emission Spectrometry (ICPQ-1000, Shimadzu, Japan) and amount of Ag dissolved from amalgam specimen was measured using Atomic Absorption Spectrophotometry (Atomic Absorption/Flame emission spectrophotometer M-670, Shimadzu, Japan). A surface corrosion products of specimens were analysed using Electron Spectroscopy Chemical Analyser (ESCA PHI-558, PERKIN ELMER, U.S.A.). The secondary image and back scattered image of corroded surface of specimens was observed under the SEM, and the corroded surface of specimens was analysed with the EDX. The following results were obtained. 1. The dissolution amount of Cu was the most in high copper admixed amalgam(Dispersalloy) and the least in high copper single composition amalgam(Tytin). 2. Sn and Zn were dissolved during all the experiment periods, and dissolution amounts were decreased as the time elapsed. 3. Initial surface corrosion products were ZnO and SnO. 4. Corrosion of ${\gamma}$ and ${\gamma}_2$ phase in low copper amalgams was observed and Ag-Cu eutectic alloy phase was corroded in low copper spherical amalgam(Caulk Sperical Alloy). 5. Corrosion of ${\gamma}$ and $\eta$' phase in high copper amalgams was observed and Ag-Cu eutectic alloy phase was corroded in high copper admixed amalgam(Dispersalloy). 6. Sn-Cl was produced in the subsurface of low copper amalgams and high copper admixed amalgam.