• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1581-1584
• /
• 2008

In dual-polycide-gate structure with butting contact, net doping concentration of polysilicon was decreased due to overlap between $n^+$ and $p^+$ and lateral dopant diffusion in silicide/polysilicon layers. The generation of parasitic Schottky diode in butting contact region is attributed both to the $CoSi_2$-loss due to $CoSi_2$ agglomeration and to the decrease in net doping concentration of polysilicon layer. Parasitic Schottky diode reduces noise margin of sense amplifier in DDI DRAM, which causes column fail. The column fail could be reduced by physical isolation of $n^+/p^+$ polysilicon junction or suppressing $CoSi_2$ agglomeration by using nitrogen implantation into $p^+$ polysilicon before $CoSi_2$ formation.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.579-583
• /
• 1998

Silicide layer structures, agglomeration of silicide layers, and dopant redistributions for the Co/Ti bilayer sputter-deposited on the P-doped polycrystalline Si substrate and subjected to rapid thermal annealing were investigated and compared with those on the single Si substrate. The $CoSi_2$ phase transition temperature is higher and agglomeration of the silicide layer occurs more severely for the Co/Ti bilayer on the doped polycrystalline Si substrate than on the single Si substrate. Also, dopant loss by outdiffusion is much more significant on the doped polycrystalline Si substrate than on the single Si substrate. All of these differences are attributed to the grain boundary diffusion and heavier doping concentration in the polycrystalline Si. The layer structure after silicidation annealing of Co/ Tildoped - polycrystalline Si is polycrystalline CoSi,/polycrystalline Si, while that of Co/TiI( 100) Si is Co- Ti- Si/epi- CoSi,/(lOO) Si.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.208-213
• /
• 1998

Silicidation of the Co/Ti/Si bilayer system in which Ti is used as epitaxy promoter for $CoSi_2$has recently received much attention. The Co/Ti bilayer on the spacer oxide of gate electrode must be thermally stable at high temperatures for a salicide transistor to be fabricated successfully. In the $SiO_2$substrate was rapid-thermal annealed. The Sheet resistances of the Co/Ti bilayer increased substantially after annealing at $600^{\circ}C$, which is due to the agglomeration of the Co layer to reduce the interface energy between the Co layer and the $SiO_2$substrate. In the bilayer system insulating Ti oxide stoichiometric Ti oxide and silicide were not found after annealing.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.3
• /
• pp.89-94
• /
• 2005

We investigate the reaction stability of cobalt and nickel with side-wall materials of $SiO_2\;and\;Si_3N_4$. We deposited 15nm-Co and 15nm-Ni on $SiO_2(200nm)/p-type$ Si(100) and $Si_3N_4(70 nm)/p-type$ Si(100). The samples were annealed at the temperatures of $700\~1100^{\circ}C$ for 40 seconds with a rapid thermal annealer. The sheet resistance, shape, and composition of the residual materials were investigated with a 4-points probe, a field emission scanning electron microscopy, and an AES depth profiling, respectively. Samples of annealed above $1000^{\circ}C$ showed the agglomeration of residual metals with maze shape and revealed extremely high sheet resistance. The Auger depth profiling showed that the $SiO_2$ substrates had no residual metallic scums after $H_2SO_4$ cleaning while $Si_3N_4$ substrates showed some metallic residuals. Therefore, the $SiO_2$ spacer may be appropriate than $Si_3N_4$ for newly proposed Co/Ni composite salicide process.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.956-960
• /
• 1998

The interfacial reaction between the CoINb bilayer and the $SiO_2$ substrate in the temperature range of $330^{\circ}C$-$800^{\circ}C$ in a vacuum has been investigated by X-ray photoelectron spectroscopy, glancing angle XRD, Auger Electron Spectroscopy and Atomic force microscopy. The Co and Nb were actively interdiffused at $600^{\circ}C$, and the layer inversion completed at $700^{\circ}C$. NbO was formed by interfacial reaction between the Nb interlayer and the $SiO_2$ substrate, while $Nb_20_5$ was formed on the surface by reaction of Nb with oxygen in the ambients. Free Si atoms obtained by the reaction between Nb and $SiO_2$ formed silicides like CoSi and $Nb_5Si_3$ by reacting with Co and Nb remnants. The sheet resistance of the Co/Nb bilayer increased substantially after annealing at $800^{\circ}C$. which is due to the agglomeration of the Co layer to reduce its surface energy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.288-291
• /
• 2002

Application of metal silicides such as TiSi$_2$ and CoSi$_2$ as contacts and gate electrodes are being studied. However, TiSi$_2$ due to the linewidth-dependance, and CoSi$_2$ due to the excessive Si consumption during silicidation cannot be applied to the deep-submicron MOSFET device. NiSi shows no such problems and can be formed at the low temperature. But, NiSi shows thermal instability. In this investigation, NiSi was formed with a Ti-capping layer to improve the thermal stability. Ni and Ti films were deposited by the thermal evaporator. The samples were then annealed in the N$_2$ ambient at 300-800$^{\circ}C$ in a RTA (rapid thermal annealing) system. Four point probe, FESEM, and AES were used to study the thermal properties of Ti-capped NiSi layers. The Ti-capped NiSi was stable up to 700$^{\circ}C$ for 100 sec. RTA, while the uncapped NiSi layers showed high sheet resistance after 600$^{\circ}C$. The AES results revealed that the Ni diffusion further into the Si substrate was retarded by the capping layer, resulting in the suppression of agglomeration of NiSi films.

• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.168-172
• /
• 1999

We have studied the formation of Co/Ti bilayer silicide with low resistivity and good thermal stability on the heavily boron doped $\textrm{p}^{+}$-Si region. In this paper, Co/Ti bilayer silicides were fabricated by depositing Co($150\AA$)/Ti($50\AA$) films on the clean $\textrm{p}^{+}$-Si substrates in an E-beam evaporator and performing the two step RTA process (first annealing: 650$50^{\circ}C$/20sec, second annealing: $800^{\circ}C$/20sec) in a $N_2$ambient with the pressure of $\textrm{10}^{-1}$atm. Co/Ti bilayer silicides obtained from our experiments exhibited the low resistivity of about $18\mu\Omega$-cm and the uniform thickness of about $500\AA$ without change of sheet resistance and agglomeration under the long post0annealing time up to $1000^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.3
• /
• pp.273-277
• /
• 2005

We prepared $0.25\~l.5um$ poly silicon gate array test group with $SiO_2$ spacers in order to employ NiCo composite salicide process from 15nm Ni/15nm Co/poly structure. We investigate the residual metal shape evolution by varying the rapid thermal silicide anneal temperature from $700^{\circ}C\;to\;1100^{\circ}C$. We observed the residual metals agglomerated into maze type and line type on $SiO_2$ field and silicide gate, respectively as temperature increased. We propose that lower silicide temperature would be favorable in newly proposed NiCo salicide in order to lessen the agglomeration causing the leakage and scum formation.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.87-92
• /
• 1998

Ultr shallow p$^{+}$-n junction with Co/Ti bilayer silicidde contact was formed by ion implantation of BF$_{2}$ [energy : (30, 50)keV, dose:($5{\times}10^{14}$, $5{\times}10^{15}$/$\textrm{cm}^2$] onto the n-well Si(100) region and by RTA-silicidation and post annealing of the evaporated Co(120.angs., 170.angs.)/Ti(40~50.angs.) double layer. The sheet resistance of the silicided p$^{+}$ region of the p$^{+}$-n junction formed by BF2 implantation with energy of 30keV and dose of $5{\times}10^{15}$/$\textrm{cm}^2$ and Co/Ti thickness of $120{\AA}$/(40~$50{\AA}$) was about $8{\Omega}$/${\box}$. The junction depth including silicide thickness of about $500{\AA}$ was 0.14${\mu}$. The fabricated p$^{+}$ -n ultra shallow junction depth including silicide thickness of about $500{\AA}$ was 0.14${\mu}$. The fabricated p$^{+}$-n ultra shallow junction with Co/Ti bilayer silicide contact did not show any agglomeration or variation of sheet resistance value after post annealing at $850^{\circ}C$ for 30 minutes. The boron concentration at the epitaxial CoSi$_{2}$/Si interface of the fabricated junction was about 6*10$6{\times}10^{19}$ / $\textrm{cm}^2$./TEX>.

• Korean Journal of Materials Research
• /
• v.29 no.10
• /
• pp.592-602
• /
• 2019

Feasibility is investigated for reduction of chromium ore by Si sludge with mixed silicothermic and carbothermic reaction. The reduction behavior of chromium ore using Si sludge is investigated precisely to determine the effects of carbon addition, reaction time, and reaction temperature. The pellets are dropped into the furnace after temperature stabilized. As the amount of C addition increases, the amounts of CO and $CO_2$ gas generation increase. After the dropping of the pellets, the pellets are heated and the reaction starts at about 1,573 K or higher. The pellets maintain their shape until 10 min after the drop, and then melted. As the holding time increased, the size of the reduced metal particles increased. The chromium ore is rapidly reduced by the Si sludge, and the slag penetrated into the chromium ore and reduction progressed inside. As the reduction temperature increased, the reaction initiation time is shortened and the reaction fraction of the reduction reaction increased. As the reaction temperature increased, agglomeration of reduced ferrochrome metal is promoted.