• 한국전기전자재료학회논문지
• /
• 제29권6호
• /
• pp.321-326
• /
• 2016

Minimizing the carrier recombination and electrical loss through surface passivation is required for high efficiency c-Si solar cell. Usually, $SiN_X$, $SiO_X$, $SiON_X$ and $AlO_X$ layers are used as passivation layer in solar cell application. Silicon oxide layer is one of the good passivation layer in Si based solar cell application. It has good selective carrier, low interface state density, good thermal stability and tunneling effect. Recently tunneling based passivation layer is used for high efficiency Si solar cell such as HIT, TOPCon and TRIEX structure. In this paper, we focused on silicon oxide grown by various the method (thermal, wet-chemical, plasma) and passivation effect in c-Si solar cell.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.758-763
• /
• 2006

We has been studied the thin film encapsulation effect for organic light-emitting diodes (OLED). To evaluate the passivation properties of the passivation layer materials, we have carried out the fabrication of green light emitting diodes with ultra violet(UV) light absorbing polymer resin, $SiO_2,\;and\;SiN_x$, respectively. From the measurement results of shrinkage properties according to the exposure time to the atmosphere, we found that $SiN_x$ thin film is the best material for passivation layer. We have investigated the emission efficiency and life time of OLED device using the package structure of $OLED/SiN_x/polymer$ resin/Al/polymer resin. The emission efficiency of this OLED device was 13 lm/W and life time was about 2,000 hours, which reach 95 % of the performance for the OLED encapsulated with metal.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.430-430
• /
• 2012

The surface recombination velocity of the silicon solar cell could be reduced by passivation with insulating layers such as $SiO_2$, SiNx, $Al_2O_3$, a-Si. Especially, the aluminium oxide has advantages over other materials at rear surface, because negative fixed charge via Al vacancy has an additional back surface field effect (BSF). It can increase the lifetime of the hole carrier in p-type silicon. The aluminium oxide thin film layer is usually deposited by atomic layer deposition (ALD) technique, which is expensive and has low deposition rate. In this study, ICP-assisted reactive magnetron sputtering technique was adopted to overcome drawbacks of ALD technique. In addition, it has been known that by annealing aluminium oxide layer in nitrogen atmosphere, the negative fixed charge effect could be further improved. By using ICP-assisted reactive magnetron sputtering technique, oxygen to nitrogen ratio could be precisely controlled. Fabricated aluminium oxy-nitride (AlON) layer on silicon wafers were analyzed by x-ray photoelectron spectroscopy (XPS) to investigate the atomic concentration ratio and chemical states. The electrical properties of Al/($Al_2O_3$ or $SiO_2/Al_2O_3$)/Si (MIS) devices were characterized by the C-V measurement technique using HP 4284A. The detailed characteristics of the AlON passivation layer will be shown and discussed.

• 한국표면공학회지
• /
• 제45권1호
• /
• pp.20-24
• /
• 2012

Multilayer passivation film on OLED with organic/inorganic hybrid structure as to diminish the thermal stress and expansion was researched to protect device from the direct damage of $O_2$ and $H_2O$ and improve life time characteristics. Red OLED doped with 1 vol.% Rubrene in $Alq_3$ was used as a basic device. The films consist of ITO(150 nm)/ELM200_HIL(50 nm)/ELM002_HTL(30 nm)/$Alq_3$: 1 vol.% Rubrene(30 nm)/$Alq_3$(30 nm) and LiF(0.7 nm)/Al(100 nm) which were formed in that order. Using LiF/$SiN_x$ as a buffer layer was determined because it significantly improved life time characteristics without suffering damage in the process of forming passivation film. Multilayer passivation film on buffer layer didn't produce much change in current efficiency, while the half life time at 1,000 $cd/m^2$ of OLED/LiF/$SiN_x$/E1/$SiN_x$ was 710 hours which showed about 1.5 times longer than OLED/LiF/$SiN_x$/E1 with 498 hours. futhermore, OLED/LiF/$SiN_x$/E1/$SiN_x$/E1/$SiN_x$ with 1301 hours showed about twice than OLED/LiF/$SiN_x$/E1/$SiN_x$ which demonstrated that superior characteristics of life time was obtained in multilayer passivation film. Through the above result, it was suggested using LiF/$SiN_x$ as a buffer layer could reduce the damage from the difference of thermal expansion coefficient in OLED with protective films, and epoxy layer in multilayer passivation film could function like a buffer between $SiN_x$ inorganic layers with relatively large thermal stress.

• 한국표면공학회지
• /
• 제42권6호
• /
• pp.287-293
• /
• 2009

The passivation films with epoxy layer on LiF, $SiN_x$ and LiF/$SiN_x$ inorganic layer were fabricated on OLED to protect device from the direct damage of $O_2$ and $H_2O$ and to apply for a buffer layer between OLED device and passivation multi-layer with organic/inorganic hybrid structure as to diminish the thermal stress and expansion. Red OLED doped with 1 vol.% Rubrene in $Alq_3$ was used as a basic device. The device structure was multi-layer of ITO(150 nm) / ELM200_HIL(50 nm) / ELM002_HTL(30 nm) / $Alq_3$: 1 vol.% Rubrene(30 nm) / $Alq_3$(30 nm) / LiF(0.7 nm) / Al(100 nm). LiF/epoxy applied as a protective layer didn't contribute to the improvement of life time. While in case of $SiN_x$/epoxy, damage was done in the passivation process because of difference in heat expansion between films which could occur during the formation of epoxy film. Using LiF/$SiN_x$/epoxy improved lifetime significantly without suffering damage in the process of forming films, therefore, the best structure of passivation film with inorganic/epoxy layers was LiF/$SiN_x$/E1.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1268-1274
• /
• 2018

We have investigated the effects of chemical rounding (CR) on the surface passivation and/or antireflection performance of $AlO_{x^-}$ and $AlO_x/SiN_x:H$ stack-passivated pyramid textured $p^+$-emitters with two different boron doping concentrations, and on the performance of bifacial n-PERT Si solar cells with a front pyramid textured $p^+$-emitter. From experimental results, we found that chemical rounding markedly enhances the passivation performance of $AlO_x$ layers on pyramid textured $p^+$-emitters, and the level of performance enhancement strongly depends on boron doping concentration. Meanwhile, chemical rounding increases solar-weighted reflectance ($R_{SW}$) from ~2.5 to ~3.7% for the $AlO_x/SiN_x:H$ stack-passivated pyramid textured $p^+$-emitters after 200-sec chemical rounding. Consequently, compared to non-rounded bifacial n-PERT Si cells, the short circuit current density Jsc of 200-sec-rounded bifacial n-PERT Si cells with ~60 and ${\sim}100{\Omega}/sq$ $p^+$-emitters is reduced by 0.8 and $0.6mA/cm^2$, respectively under front $p^+$-emitter side illumination. However, the loss in the short circuit current density Jsc is fully offset by the increased fill factor FF by 0.8 and 1.5% for the 200-sec-rounded cells with ~60 and ${\im}100{\Omega}/sq$ $p^+$-emitters, respectively. In particular, the cell efficiency of the 200-sec-rounded cells with a ${\sim}100{\Omega}/sq$ $p^+$-emitter is enhanced as a result, compared to that of the non-rounded cells. Based on our results, it could be expected that the cell efficiency of bifacial n-PERT Si cells would be improved without additional complicated and costly processes if chemical rounding and boron doping processes can be properly optimized.

• Transactions on Electrical and Electronic Materials
• /
• 제16권5호
• /
• pp.227-233
• /
• 2015

To reduce the cost of solar electricity, the crystalline-silicon (c-Si) photovoltaic industry is moving toward the use of thinner wafers (100 μm to 200 μm) to achieve a high efficiency. In this field, it is imperative to achieve an effective passivation method to reduce the electronic losses at the c-Si interface. In this article, we review the most promising surface passivation schemes that are available for high-efficiency solar cells.

• ETRI Journal
• /
• 제27권5호
• /
• pp.545-550
• /
• 2005

We have carried out the fabrications of a barrier layer on a polyethersulfon (PES) film and organic light emitting diode (OLED) based on a plastic substrate by means of atomic layer deposition (ALD). Simultaneous deposition of 30 nm $AlO_x$ film on both sides of the PES film gave a water vapor transition rate (WVTR) of $0.062 g/m^2/day (@38^{\circ}C,\;100%\;R.H.)$. Further, the double layer of 200 nm $SiN_x$ film deposited by plasma enhanced chemical vapor deposition (PECVD) and 20 nm $AlO_x$ film by ALD resulted in a WVTR value lower than the detection limit of MOCON. We have investigated the OLED encapsulation performance of the double layer using the OLED structure of ITO / MTDATA (20 nm) / NPD (40 nm) / AlQ (60 nm) / LiF (1 nm) / Al (75 nm) on a plastic substrate. The preliminary life time to reach 91% of the initial luminance $(1300 cd/m^2)$ was 260 hours for the OLED encapsulated with 100 nm of PECVD-deposited $SiN_x$ and 30 nm of ALD-deposited $AlO_x$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.452-452
• /
• 2010

차세대 디스플레이로서 주목 받고 있는 유연성 정보표시 소자 개발에 대한 요구도가 날로 증대되고 있다. 유연성 정보표시 소자로서 플라스틱 기반 유연성 소자가 특히 주목 받고 있으나, 이의 실용화를 위해서는 플라스틱 기판에 적용 가능한 보호막 형성 기술 개발이 선행되어야 한다. 플라스틱 필름의 경우 높은 산소 및 수분 투과율 때문에 유연성 디스플레이의 응용에 걸림돌이 되고 있다. 플라스틱 기반 유연성 소자의 장수명화를 위해서는 수분과 산소의 투과를 방지하는 passivation layer 형성 기술이 필수적으로 요구된다. 본 연구에서는, polyethylene terephethalate (PET) 기판상에 증착된 $SiO_x$ 보호막의 합성에 있어서 중간층 유무에 따른 투습특성의 변화를 살펴보았다. 기화된 HMDSO (Hexamethyldisiloxane)와 Ar 및 $O_2$ 혼합기체를 이용하여 PECVD 방법으로 $SiO_x$ 박막을 합성하였다. 15 nm 두께의 $Al_2O_3$를 중간층으로 사용하여 중간층 유무에 따른 초기성장 거동 변화가 $SiO_x$ 박막의 투습 특성에 미치는 영향을 조사하였다. $SiO_x$ 박막 구조와 화학적 조성은 각각 FE-SEM과 FT-IR을 이용하여 분석하였으며, AFM을 이용하여 $SiO_x$ 박막 표면 미세 형상을 관찰하였다. 투습률은 MOCON사(社)의 Permatran-W 3/33 MA을 이용하여 측정하였다. 그리고 반복 굽힘 시험기를 이용하여 $SiO_x$ 보호막의 동적 투습 특성을 조사하였다. $Al_2O_3$ 중간층 유무에 따라 $SiO_x$ 박막의 투습률 (WVTR; water vapor transmission rate)은 ${\sim}10^{-1}g/m^2/day$(300 nm-thick $SiO_x$/PET)에서 ${\sim}5{\times}10^{-3}g/m^2/day$(300 nm-thick $SiO_x$/15 nm-thick $Al_2O_3$/PET)으로 변화하였다. 300 nm-thick $SiO_x$/15 nm-thick $Al_2O_3$/PET 시편의 경우 곡지름 50 mm에서 1,000회 반복 굽힘 후에도 투습률 변화를 보이지 않았다. 이와 같은 $SiO_x$ 박막의 투습 특성 변화는 $Al_2O_3$ 중간층 유무에 따른 초기 성장 거동의 변화로 해석된다. FE-SEM 및 AFM 표면 미세 구조 관찰을 통한 초기 성장 거동 변화 조사 결과, $Al_2O_3$ 중간층 없이 PET 기판위에 $SiO_x$ 박막 증착한 경우 3 차원 성장을 하는 반면, PET기판위에 $Al_2O_3$ 중간층 형성 후 $SiO_x$ 박막 증착하는 경우 2 차원 성장을 하게 됨을 관찰하였다. 따라서 본 연구를 통하여, 플라스틱 기반 유연성 표시 소자에 적용하기 위한 $SiO_x$ 보호막 합성 에 있어서 초기 성장 거동의 변화가 투습 특성에 민감한 영향을 미침을 알 수 있었다.

• 한국표면공학회지
• /
• 제49권5호
• /
• pp.467-471
• /
• 2016

In order to investigate the Na gettering, PSG/$SiO_2$/Al-1%Si multilevel thin films were fabricated. DC magnetron sputter techniques and APCVD (atmosphere pressure chemical vapor deposition) were utilized for the deposition of Al-1%Si thin films and PSG/$SiO_2$ passivations, respectively. Heat treatment was carried out at $300^{\circ}C$ for 5 h in air. SIMS (secondary ion mass spectrometry) depth profiling and XPS (X-ray Photoelectron Spectroscopy) analysis were used to determine the distribution and binding energies of Na, Al, Si, O, P and other elements throughout the PSG/$SiO_2$/Al-1%Si multilevel thin films. Na peaks were mainly observed at the the PSG/$SiO_2$ interface and at the $SiO_2$/Al-1%Si interfaces. Na impurity gettering in PSG/$SiO_2$/Al-1%Si multilevel thin films is considered to be caused by a segregation type of gettering. The chemical state of Si and O elements in PSG passivation appears to be $SiO_2$.