권호 표지

한국해양공학회지 (Journal of Ocean Engineering and Technology) (Journal of Ocean Engineering and Technology)

한국해양공학회 (Korean Society of Ocean Engineers)

  • 격월간
  • /
  • 1225-0767(pISSN)
  • /
  • 2287-6715(eISSN)

Aim & Scope

The “Journal of Ocean Engineering and Technology” (JOET) was launched in 1987 and is published bimonthly in February, April, June, August, October, and December each year by “The Korean Society of Ocean Engineers (KSOE).” Its ISO abbreviation is “J. Ocean Eng. Technol.” JOET publishes original research articles, technical articles, and review articles on all aspects of ocean engineering, including experimental, theoretical, numerical, and field observations. All manuscripts undergo peer-review by two or more reviewers. The scope of JOET encompasses the following research areas: - Ships and offshore engineering: Design of ships and offshore structures; Resistance and propulsion; Seakeeping and maneuvering; Experimental and computational fluid dynamics; Ocean wave mechanics; Fatigue strength; Plasticity; Optimization and reliability; Arctic technology and extreme mechanics; Noise, vibration, and acoustics; Concrete engineering; Thermodynamics and heat transfer; Hydraulics and pneumatics; Autonomous and unmanned ship; Greenship technology; Digital twin of ships and offshore structures; Marine materials - Coastal engineering: Coastal, port, and harbor structures; Waves transformation; Coastal and estuary hydrodynamics; Sediment transport and morphological change; Subsea geotechnics; Coastal groundwater management; Prevention or mitigation of coastal disaster; Coastal zone development and management; Shore protection technique; Coastal environmental process; Beach safety - Ocean energy engineering: Offshore wind turbines; Wave energy platforms; Tidal current energy platforms; Floating photovoltaic energy platform; Small modular reactor; Combined energy platforms - Marine robot engineering: Robot sensor system; Autonomous navigation; Robot equipment; Marine robot control; Environment mapping and exploration; Underwater communication and networking; Design of marine robots

https://www.joet.org KSCI KCI

제12권2호통권28호

  1. 윤태혁;권영두 1
    PDF
    In this paper, a non-conforming 3-D 8-node solid element(MQM10) has beets applied to the analyses of static and dynamic bending problems of laminated composite plates The QM10 element exhibits stiffer bending stiffness which is caused by the reduction of degree of freedom from Q11 element. As an effective way to correct the relative stiffness stiffening phenomenon the modification of Gauss sampling points for composite plates is proposed. The quantity of modification is a function of material properties. Also, another two modified equations are obtained, one is modification for stress, and the other is modification of coefficient of shear modulus in free vibration. It is noted that MQM10 element can analyse the static and free vibration problems of various 3-dimensional composite plates composed of unidirectional laminae, woven laminae or braided laminae. The results of MQM10 element are in good agreement with those of 20-node element.
  2. 김사수;조대승;안호일;정상민 22
    PDF
    Many of steel structures having little internal damping consist of stiffened plates. In case that viscoelastic materials are adhered to the stiffened plates for the reduction of structure-borne noise, their effects are varied by the adhered position and dynamic characteristics of the structures as well as their material properties and adhered amount. In this paper, sound reduction effects of viscoelastic materials partially adhered to the different positions of a stiffened steel plate have been investigated by the measurement of vibratory velocity and sound intensity. The results show that optimal adherent positions of viscoelastic materials to reduce sound radiation power are the loop areas of modes.
  3. 이창호;구자삼;조효제;홍봉기 33
    PDF
    In the presence of incident waves with different frequencies, the second order sum and difference frequency waves due to the nonlinearity of the incident waves come into existence. Although the magnitudes of the forces produced on a Tension Leg Platform(TLP) by these nonlinear waves are small, they act on the TLP at sum and difference frequencies away from those of the incident waves. So, the second order sum and difference frequency wave loads produced close to the natural frequencies of TLPs often give greater contributions to high and low frequency resonant responses. The second order wave exciting forces and moments have been obtained by the method based on direct integration of pressure acting on the submerged surface of a TLP. The components of the second order forces which depend on first order quantities have been evaluated using the three dimensional source distribution method. The numerical results of time domain analysis for the nonlinear wave exciting forces in regular waves are compared with the numerical ones of frequency domain analysis. The results of comparison confirmed the validity of the proposed approach.
  4. 구자삼;조효제;김병현;이창호 43
    PDF
    A barge-type structure has been recently watched since The Floating Structures Association of Japan proposed the new concept as the most suitable one of floating airports. In this paper, the method, which is based on a combination of a three-dimensional source distribution method and the wave interaction theory is applied to very large floating structure of barge-type. The calculated results show good agreement with the experimental and calculated ones by Yago and remarkable characteristics concerning the hydroelastic behavior of the very large floating structure on the effects of hydrodynamic interactions and choice of body modelling.
  5. 정동원;양경부 57
    PDF
    This study is concerned with criterion for membrane to shell conversion in two-dimensional elastic-plastic finite element analysis using membrane/shell mixed element. It is well known that in the sheet metal forming some parts of the sheet deform under almost pure stretching (membrane) conditions, whereas other parts in contact with sharp tooling surfaces can develop significant bending strains. The membrane analysis has a short computational time however, in the membrane analysis the bending effects can not be condidered at all. On the other hand, the shell analysis allows the consideration of bending effects, but involves too much computational time. So Onatel),2), Yang et al3),4) developed the membrane/shell mixed element. Onate introduced the energy ratio parameter and Yang et al introduced the ratio of thickness to radius of curvature as the criterion. In the present study we propose a new criterion by using the angle between both side elements in the nodal point.
  6. 이상국;정민화;오세규;송정근 65
    PDF
    In this report, the creep properties and creep life estimation by Larson-Miller Parameter(LMP) Method for 2.25Cr1Mo steel to be used as power plant tubes or other components were presented at the high temperatures of 500, 550, and $600^{\circ}C$. It was confirmed experimentally and quantitatively that a creep life estimation equation at such various high temperatures was well derived by LMP and could be used very effectively within the creep life of 10$^3$ hours, but very unreliable and even dangerous for design in a long term of creep life such as 10$^4$ or $10^5$ hours.
  7. 이상국;정민화;오세규;송정근 71
    PDF
    In this report for the assessment of creep properties of high-temperature tube materials in power plants, the long-time($10^4$~105h) creep life prediction by ISM for 2.25Cr1Mo steel was studied. It was clarified experimentally and quantitatively that the newly developed long-time creep life prediction equation was very coincident with the actual experimental data with high confidence, and the model was $t_r=\alpha\varepsilon_0^{\beta}\sigma^{-1}$.
  8. 곽승현 79
    PDF
    A three-dimensional WIG (Wing In Ground effect) moving above free surface is numerically studied by means of finite difference techniques. The air flow field around the WIG is analyzed by MAC (Marker & Cell) method, and interactions between WIG and the free surface are appeared as the variation of pressure distribution acting on the free surface. To analyze the wavemaking phenomena by those pressure distributions, the NS (Navier-Stokes) solver is employed in which nonlinearities of the free surface conditions can be included. Through the numerical simulation, Cp values and lift/drag ratio are carefully reviewed by changing the height/chord ratio. The section shape of model is NACA0012 with the span/chord ratio of 3.0. Through computational results, it is confirmed that the effect of free surface is small enough to treat it as a rigid wavy wall.
  9. 정광효;장종희;전호환 87
    PDF
    A numerical simulation was done to investigate the performance of thin wings in close vicinity to ground. The simulation is based on Vortex Lattice Method(VLM) and freely deforming wake elements are taken into account for a sudden acceleration case. The parameters covered in the simulation are angle of attack, aspect ratio, ground clearance, sweep angle and taper ratio. In addition, the effect of the wing endplate on the ground effect is included. The wing sections used for present computations are uncambered, cambered and S-types. The present computational results are compared with other published computational results and experimental data.
  10. 이광호;전호환;성창경 97
    PDF
    The numerical damping and dispersion error characteristics associated with difference schemes and a panel shift method used for the calculation of steady free surface flows by a panel method are an analysed in this paper. First, 12 finite difference operators used for the double model flow by Letcher are applied to a two dimensional cylinder with the Kelvin free surface condition and the numerical errors with these schemes are compared with those by the panel shift method. Then, 3-D waves due to a submerged source are calculated by the difference schemes, the panel shift method and also by a higher order boundary element method(HOBEM). Finally, the waves and wave resistance for Wigley's hull are calculated with these three schemes. It is shown that the panel shift method is free of numerical damping and dispersion error and performs better than the difference schemes. However, it can be concluded that the HOBEM also free of the numerical damping and dispersion error is the most stable, accurate and efficient.
  11. 신동수;배기성 111
    PDF
    Laboratory settling experiments (column, recirculating flume) were conducted for further understanding of the physical processes of cohesive sediment transport. \In still water experiments, the growth rate of flocculation is dependent upon the initial suspended concentration. Consequently, the settling velocity increases with concentration of flees. In flocculation settling regime, the exponent n in the settling velocity, $w_s=kC^n$, for Nakdong estuary mud was obtained empirically. The exponents were found to be 1.33, and 1.06 for the initial suspended concentrations of 1 g/i and 3 g/t, respectively. In flowing water, experiments for the median settling velocity with Nakdong mud in a recirculating flume were conducted. Settling velocity was found to depend much more strongly on the current velocity than initial concentrations. The temporal variation of suspended concentration increases as current velocity decreases.
  12. 조효제;도덕희 121
    PDF
    A quantitative non-contact multi-point measurement system is proposed to the measurement of three-dimensional movement of floating vessels by using digital image processing. The instantaneous three-dimensional movement of a floating structure which is floating in a small water tank is measured by this system and its three-dimensional movement is reconstructed by the measurement results. The validity of this system is verified by position identification for spatially distributed known positional values of basic landmarks set for the camera calibration. It is expected that this system is applicable to the non-contact measurement for an unsteady physical phenomenon especially for the measurement of three-dimensional movement of floating vessels in the laboratory model test.
  13. 이판묵;전봉환;홍석원 130
    PDF
    본 논문은 AUV의 수직면 운동제어를 수행하기 위하여 의사 슬라이딩 모드 제어기를 이용한 모델링 기법과 제어기 설계법에 관한 것으로서, 샘플링 간격이 길어지는 경우에도 시스템의 강인성이 확보되며 심도 제어가 안정적으로 수행되는 실용성을 실험과 수치 해석을 통하여 검증하였다. 제어기는 참고문헌에서 제안한 방법을 이용하였으며, 한국기계연구원 선박해양공학연구센터(KRISO)에서 개발한 VORAM호를 제어 대상 AUV로 선정하였다. PMM 시험으로 얻어진 운동 계수를 이용하여 수치 해석을 수행하였으며, KRISO의 장수조에서 실험을 수행하였다. 수치 해석과 실험 결과로부터 샘플링이 길어짐에 따라 의사 슬라이딩 모드 제어기는 연속계에 대한 슬라이딩 모드 제어기에서 발생하는 과도한 채터링 및 불안정성을 보이지 않았으며, 시스템의 안정성이 확보되고 불확실성에 대하여 강인한 제어 성능을 보였다. 또한, 본 논문에서는 수치 해석과 실험 결과를 근거로 의사 슬라이딩 모드 제어기의 설계를 위한 제어 변수의 선정 기준을 제시하였다.
  14. 김상봉;감병오;강병철;김동규 139
    PDF
    This paper introduces a network system for monitoring coastal oceanographic data. The network system consists of three parts such as the buoy to observe oceanographic data, the local site to collect data transferred from buoys, and the host site to construct the oceanographic data-base and to share the information for monitoring coastal oceanographic data. The buoy has a one-board microcomputer to manage and to acquire coastal environment data in real-time. A wireless and wire communication technique is employed in order to transfer data measured by buoys and to link local and host sites, respectively. In measuring coastal environment data, this system shows more cost-effective way than the presents conventional. In addition, the realtime monitoring system continuously from various sites with the network systems.
  15. 심재우 147
    PDF
    In this study turbine flowmeters were used to predict volumetric flow rate of each phase in two-phase, gas-liquid, flowing in a vertical tube. To determine volumetric flow rates of two-phase, air-water, flowing vertically upward through the polycarbonate tube(57mm ID-inside diameter), two turbine flow meters were used. For void fraction measurements, two gamma densitometers were used at each location of the turbine flow meter, one at the upstream and the other at the downstream. It was determined that the turbine flowmeter's outputs were a function of actual volumetric flow rate of each of the two phases. A two-phase flow model was developed.