• ETRI Journal
• /
• 제33권6호
• /
• pp.897-903
• /
• 2011

A hybrid ${\Delta}{\Sigma}$ modulator for audio applications is presented in this paper. The pulse generator for digital-to-analog converter alleviates the requirement of the external clock jitter and calibrates the coefficient variation due to a process shift and temperature changes. The input resistor network in the first integrator offers a gain control function in a dB-linear fashion. Also, careful chopper stabilization implementation using return-to-zero scheme in the first continuous-time integrator minimizes both the influence of flicker noise and inflow noise due to chopping. The chip is implemented in a 0.13 ${\mu}m$ CMOS technology (I/O devices) and occupies an active area of 0.37 $mm^2$. The ${\Delta}{\Sigma}$ modulator achieves a dynamic range (A-weighted) of 97.8 dB and a peak signal-to-noise-plus-distortion ratio of 90.0 dB over an audio bandwidth of 20 kHz with a 4.4 mW power consumption from 3.3 V. Also, the gain of the modulator is controlled from -9.5 dB to 8.5 dB, and the performance of the modulator is maintained up to 5 nsRMS external clock jitter.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1642-1649
• /
• 2018

A single-stage flyback LED AC-DC converter based on primary-side control under constant current mode is proposed in this study. The proposed converter features low total harmonic distortion (THD) and high power factor (PF). It also consists of a zero-crossing distortion compensation circuit and a variable duty ratio control compensation circuit to deal with the line current distortions caused by fixed duty ratio control. The system model and layout are built in Simplis and Cadence, respectively. The feasibility and performance of the proposed circuit is verified by designing and fabricating an IC controller in the HHNEC $0.35{\mu}m$ 5 V/40 V HVCMOS process. Experimental results show that the PF can reach a level in the range of 0.985-0.9965. Moreover, the average THD of the entire system is approximately 10%, with the minimum being 6.305%, as the input line voltage changes from 85 VAC to 265 VAC.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.279-284
• /
• 2005

We investigated the impedance matching characteristics of UHF-band RFID tag antenna and tag chip for increased reading range. A voltage multiplier designed using 0.4 $\mu$m zero-$V_T$ MOSFET showed that DC output voltage of about 2 V can be obtained using standard CMOS process. The input impedance of the voltage multiplier was examined to achieve impedance matching to the RFID tag antenna using analytical and numerical approaches. The input impedance of the voltage multiplier could be varied in a wide range by selecting the size of MOSFET and the number of multiplying stages, and thus can be impedance matched to a tag antenna in presence of other tag circuit blocks. A meander line inductively-coupled RFID tag antenna operating at UHF band also shows the feasibility of impedance matching to tile RFID tag chip.

• 대한기계학회논문집B
• /
• 제27권6호
• /
• pp.693-700
• /
• 2003

The effect of the configuration of the nozzle and the impinging surface on the characteristics of the hole-tones has been experimentally investigated. It is found that the plate-tone is a special case of hole-tones, where the hole diameter is zero. The jet velocity range for hole-tones is divided into the low velocity region associated with laminar jet and the high velocity region with turbulent jet. The frequency of the tone is that for the shear layer instability at the nozzle exit or that attainable by a cascade of vortex pairing process with increase of the impinging distance. When the distance is longer than one diameter the frequency decreases to the terminal value near the preferred frequency of the column mode instability, in the range 0.23< $St_d$<0.53, where $St_d$ is the Strouhal number defined by $fd/U_J$, f the frequency, d the nozzle diameter, and $U_J$ the exit velocity. While the convection speed of the downstream vortex, in the present study, is almost constant at low-speed laminar jet, it increases with distance at high-speed turbulent jet. As the frequency increases, the convection speed decreases in the low frequency range corresponding to the preferred mode, in agreement with the existing experimental data for a free jet.

• 청정기술
• /
• 제16권2호
• /
• pp.117-123
• /
• 2010

본 연구에서는 Au(I) 이온을 함유한 시안 용액으로부터 다른 형태의 금을 회수하기 위하여 생체흡착 후 탈착하는 방법과 생체흡착 후 회화하는 방법을 제안하였다. 생체흡착제로는 아미노산 발효 공정에서 발생하는 균체 폐기물(Corynebacterium glutamicum)을 사용하였다. 바이오매스의 흡착 특성을 알아 보기 위하여 pH edge 실험을 수행하였으며, 그 결과 흡착성능은 pH 2-3 부근에서 우수한 결과를 보였다. 또한, 등온흡착 실험 결과를 Langmuir 모델에 적용한 결과 Au(I)의 최대 흡착량은 pH 2.5에서 35.15 mg/g이었다. 흡착 속도론 실험을 통해 흡착 평형은 60분 이내의 짧은 시간 내에 이루어지는 것을 확인하였다. Au(I)을 회수하기 위하여 바이오매스에 흡착된 Au(I)을 탈이온수를 이용하여 탈착을 시켰으며, 탈착효율은 91%로 평가되었다. 이 결과는 바이오매스를 이용하여 흡착과 탈착을 통해 1가 금을 효과적으로 회수할 수 있음을 보여준다. 영가 형태로 회수하기 위하여, 금을 흡착하고 있는 생체흡착제를 회화하여 환원된 형태의 금을 성공적으로 회수하였으며, 회분 중 금의 순도는 85% 이상이었다. 따라서 본 연구에서 제시한 생체흡착 후 탈착(1가 형태) 공정과 생체흡착 후 회화(영가 형태) 공정은 회수하고자 하는 금의 산화수에 따라 선택하여 사용될 수 있을 것으로 기대된다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제20권6호
• /
• pp.117-126
• /
• 2015

Reductive degradation of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) by nanoscale zero-valent iron (nZVI) was investigated to evaluate the feasibility of using it for in-situ groundwater remediation. Batch experiments were conducted to quantify the kinetics and efficiency of RDX removal by nZVI, and to determine the effects of pH, dissolved oxygen (DO), and ionic strength on this process. Experimental results showed that the reduction of RDX by nZVI followed pseudo-first order kinetics with the observed rate constant (k_obs) in the range of 0.0056-0.0192 min⁻¹. Column tests were conducted to quantify the removal of RDX by nZVI under real groundwater conditions and evaluate the potential efficacy of nZVI for this purpose in real conditions. In column experiment, RDX removal capacity of nZVI was determined to be 82,500 mg/kg nZVI. pH, oxidation-reduction potential (ORP), and DO concentration varied significantly during the column experiments; the occurrence of these changes suggests that monitoring these quantities may be useful in evaluation of the reactivity of nZVI, because the most critical mechanisms for RDX removal are based on the chemical reduction reactions. These results revealed that nZVI can significantly degrade RDX and that use of nZVI could be an effective method for in-situ remediation of RDX-contaminated groundwater.

• 한국조명전기설비학회지:조명전기설비
• /
• 제9권3호
• /
• pp.88-96
• /
• 1995

고속 엘리베이터는 높은 안정성과 제어성이 필요하므로 기동, 정지시에 영 속도를 포함한 정밀 구동이 필요하다. 유도전동기의 정밀 구동을 위하여 사용되어온 벡터 제어 기법은 슬립 주파수 제어에 의한 간접 벡터 제어와 계자편향에 의한 직접벡터 제어의 두가지 종류로 분류할 수 있으며, 직접벡터제어의 경우 전동기 제어 변수의 변화에 강건한 반면에 직접 벡터 제어의 경우 비교적 넓은 속도구간에서 제어가 가능하다는 장점을 가지고 있다. 본 논문에서 토크는 직접 벡터기반으로 제어하고, 지속은 간접 벡터 기반으로 제어함으로써 유도전동기의 과도상태 동작과 시동시 영 속도 부근 및 저속 영역에서의 동작이 보다 강건하도록 개선된 직접토크-간접자속(DTIF, Direct Torque Indirect Flux)제어기를 제시하였다. 3상 유도전동기의 구동을 위하여 제안된 시스템의 수행결과는 시뮬레이션과 실험을 통하여 입증하였으며, 영 속도부근과 저속에서 고속으로의 변환과정은 속도응답에 대한 상전압, 상전류 그리고 DC링크 전류를 비교 측정하여 안정하고 강건한 속도변화가 이루어짐을 확인 할 수 있었다.

• 센서학회지
• /
• 제26권6호
• /
• pp.438-444
• /
• 2017

In this paper, we focus on optimization of the in-situ phosphorous (P) doping of low-pressure chemical vapor deposited (LPCVD) poly Si resistors for obtaining near-zero temperature coefficient of resistance (TCR) at temperature range from 25 to $600^{\circ}C$. The deposited poly Si films were annealed by rapid thermal anneal (RTA) process at the temperature range from 900 to $1000^{\circ}C$ for 90s in nitrogen ambient to relieve intrinsic stress and decrease the TCR in the poly Si layer and get the Ohmic contact. After the RTA process, a roughness of the thin film was slightly changed but the grain size and crystallinity of the thin film with the increase in anneal temperature. The film annealed at $1,000^{\circ}C$ showed the behavior of Schottky contact and had dislocations in the films. Ohmic contact and TCR of $334.4{\pm}8.2$ (ppm/K) within 4 inch wafer were obtained in the measuring temperature range of 25 to $600^{\circ}C$ for the optimized 200 nm thick-poly Si film with width/length of $20{\mu}m/1,800{\mu}m$. This shows the potential of in-situ P doped LPCVD poly Si as a resistor for pressure sensor in harsh environment applications.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.261-263
• /
• 2007

Authentication is a mechanism to establish proof of identities, the authentication process ensure that. Who a particular user is. Nowadays PC and laptop user authentication systems are always done once a hold until s explicitly revoked by the user, or asking the user to frequently reestablish his identity which encouraging him to disable authentication. Zero-Interaction Authentication (ZIA) provides solution to this problem. In ZIA,. a user wears a small authentication token that communicates with a laptop over a short-range, wireless link. ZIA combine authentication with a file encryption. Here we proposed a Laptop-user Authentication Based Mobile phone (LABM). In our model of authentication, a user uses his Bluetooth-enabled mobile phone, which work as an authentication token that provides the authentication for laptop over a Bluetooth wireless link, m the concept of transient authentication with our combining It with encryption file system. The user authenticate to the mobile phone infrequently. In turn, the mobile phone continuously authenticates to the laptop by means of the short-range, wireless link.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1150-1159
• /
• 2017

Flexibility in the power control of ultrasonic transducers has remained a challenge for cleaning applications. This paper introduces a modification of the existing piezoelectric ceramic transducer (PCT) circuit to increase the range of operation through its impedance characteristics. The output power is controlled using the asymmetrical voltage-cancellation (AVC) method. Together with a phase-locked loop control, the switching frequency of the inverter is automatically adjusted to maintain a lagging phase angle under load-parameter variations during the cleaning process. With the proposed modification, the region of the zero-voltage switching (ZVS) operation is extended, which results in a wider range of output power control. A hardware prototype is constructed and the control algorithm is implemented using an STM32F4 microcontroller. Simulation and experimental results are provided to verify the proposed method for a 50-W PCT. The operating frequency and output power ranges under study are 37 - 41 kHz and 15.8 - 50 W, respectively.