• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.15-23
• /
• 2004

In order to investigate efficiency and flowfield charateristics of the intake-diffuser for the ship waterjet propulsion, new experimental verification technology was set up in the cavitation tunnel. 1-hole and 5-hole pilot tubes were designed and manufactured to measure the pressure and velocity distributions at intake-diffuser entrance and impeller inlet. The calibration of the 5-hole pilot tubes is conducted at the cavitation tunnel The cavitation inception occurs at the intake lip, and the occurrence position depends on IVR (Inlet Velocity Ratio) condition. The present experimental device will be applied sufficiently for the development of the design and performance improvement technologies.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.4
• /
• pp.11-18
• /
• 1998

This study describes sea trial tests for a waterjet propulsion system attached in the hybrid super high speed cargo ship named "Narae". A measuring technique of jet velocity, gross thrust and impeller torque for the waterjet system is explained. From the measured data in sea trial test, performance of the waterjet propulsion system is analyzed and compared with model test results of a similar waterjet system which was carried out in 1996. The erective horse power estimated from sea trial tests shows a good agreement with resistance test results of the model ship. The optimum rising height is estimated as 0.75 m, and the overall efficiency of the waterjet system is predicted as 0.315 at 15 knots. Useful data such as the pump performance, the jet efficiency, the losses of inlet duct and nozzle were obtained. Test results show a similar behavior to the model test results.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.1
• /
• pp.30-37
• /
• 2010

In order to control the weight balance of the waterjet propulsion ship, the pump's weight needed to be decreased. We reduced length of pump hub, overall length of pump and chord length of impeller and stator. To keep pump efficiency and cavitation performance similar to the $1^{st}$design pump, optimum design and experiment were conducted. This paper describes experimental method and numerical analysis for pump design. At the blade design stage, performance analysis of the pump is conducted using commercial CFD codes ($BladeGen^+$,CFX-10). Required performance and cavitation characteristics of the design pumps were measured and observed using the stand-alone test apparatus. The weight of the pump was successfully decreased through a series of pump design processes composed of blade design, performance analysis and model test.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.6 s.144
• /
• pp.575-582
• /
• 2005

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.8-14
• /
• 2004

The numerical analysis of a waterjet propulsion system was performed to provide detail understanding of complicated flow phenomena including interactions of intake duct, rotor, stator, and contracted discharge nozzle. The incompressible RANS equations were solved on moving multiblocked grid system. To handle interface boundary between rotor and stator, the sliding multiblock method was applied. The numerical results were compared with experiments and good agreement was obtained. The complicated viscous flow features of the waterjet, such as secondary flow inside the intake duct, the recovery of axial flow by the role of the stator, and tip and hub vortex, etc. were well analyzed by the present simulation. The performance of thrust and torque was also predicted.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.5
• /
• pp.21-27
• /
• 2004

A waterjet propulsion system has many advantages compared with a conventional screw propeller especially for amphibious military vehicles because of a good maneuverability at low speed, good operating ability at shallow water, high thrust at low speed to aid maneuverability and exit from water, etc. Especially, compact design is important for the tracked-vehicle because of buoyancy in water and available space inside the tracked vehicle. The experiment is parametrically performed for various impeller diameters for more compact design. The experimental results are analyzed according to the ITTC 1996 standard analysis method as well as the conventional propulsive factor analysis method. The full-scale effective and delivered power of the tracked-vehicle are evaluated according to the variation of impeller diameter. This paper emphasized the effect of impeller diameter on the performance of waterjet system.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.1 s.139
• /
• pp.1-9
• /
• 2005

Waterjet propulsion is widely used to thrust high speed marine vessels in excess of 30-35 knots by virtue of the high propulsive efficiency, good maneuverability, and less cavitation. From the aspect of power loss, approximately $7-9\%$ of the total power is lost in intake duct due to the flow separation, nonuniformity, etc. Thus, detail understanding of flow phenomena occurring within intake duct is essential to reduce the power loss, as well as noise and vibration. The present work solved 30 incompressible RANS equations to provide complicated viscous flow features of intake duct. The numerical results were compared with experiments and good agreements were obtained for three jet velocity ratios.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.68-72
• /
• 2000

In the present paper, the numerical calculations for the viscous duct flow of water jet propulsion systems ship are carried out. The governing equation, incompressible Navier-Stokes equation, is discretized and analysed by a Method with the stcandard turbulence modeling. For the calculations the duct flow which h e intake flows disturbed by the ship, the results dcuhted by the potenti used Numerical results show fairly good agreement with the experimental data

• Journal of Ship and Ocean Technology
• /
• v.4 no.4
• /
• pp.34-44
• /
• 2000

This paper deals with the sea trial results of a fast craft with the hybrid supported type hul form. waterjet propulsion system and motion control system. The hybrid-type container ship operable in the sea with a wave height of y6 m, a speed of 50 knots and a payload of 1,500 tons were designed. A 1/8 scale 10 m- long test craft was constructed and tested in open seas. The hydrodynamic performance such as speed, turning, motion control in waves and waterjet thrush was analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.5
• /
• pp.14-20
• /
• 2004

The aim of this paper is to analyze the steady performance of POD-type waterjet system by panel method. A surface panel method is applied to the present analysis. To analyze the compound propulsor. analysis program has been developed based on a perturbation potential method. The developed code has been validated by comparing the experimental data of shrouded propeller. The validated code has been applied to the POD-type waterjet system which can be used for the propulsion of amphibious vehicle. The computed results have been compared with experimental results. which shows a good agreement between them.