• Membrane and Water Treatment
• /
• v.1 no.4
• /
• pp.297-316
• /
• 2010

Membrane fouling is one of the major operational concerns of membrane processes which results in loss of productivity. This paper investigates the ultrafiltration (UF) results of synthetic oil-in-water (o/w) emulsion using flat sheets of polysulfone (PSf) membrane synthesized with four different compositions. The aim is to identify the mechanisms responsible for the observed permeate flux reduction with time for different PSf membranes. The experiments were carried out at four transmembrane pressures i.e., 68.9 kPa, 103.4 kPa, 137.9 kPa and 172.4 kPa. Three initial oil concentrations i.e., 75 $mgL^{-1}$, 100 $mgL^{-1}$ and 200 $mgL^{-1}$ were considered. The resistance-in-series (RIS) model was applied to interpret the data and on that basis, the individual resistances were evaluated. The significances of these resistances were studied in relation to parameters, namely, transmembrane pressure and initial oil concentration. The total resistance to permeate flow is found to increase with increase in both transmembrane pressure and initial oil concentration while for higher oil concentration, resistance due to concentration polarization is found to be the prevailing resistance. The applicability of the constant pressure filtration models to the experimental data was also tested to explain the blocking process. The study shows that intermediate pore blocking is the dominant mechanism at the initial period of UF while in the later period, the fouling process is found to approach cake filtration like mechanism. However, the duration of pore blocking mechanism is different for different membranes depending on their morphological and permeation properties.

• Food Science of Animal Resources
• /
• v.39 no.2
• /
• pp.309-323
• /
• 2019

Fish oil consists of omega-3 fatty acids which play an important role in human health. Its susceptibility to oxidation causes considerable degradation during the processing and storage of food products. Accordingly, encapsulation of this ingredient through freeze drying was studied with the aim of protecting it against environmental conditions. Gum arabic (GA) was used as the wall material for fish oil nanoencapsulation where tween 80 was applied as the emulsifier. A water-in-oil (W/O) emulsion was prepared by sonication, containing 6% fish oil dispersed in aqueous solutions including 20% and 25% total wall material. The emulsion was sonicated at 24 kHz for 120 s. The emulsion was then freeze-dried and the nanocapsules were incorporated into probiotic fermented milk, with the effects of nanocapsules examined on the milk. The results showed that the nanoparticles encapsulated with 25% gum arabic and 4% emulsifier had the highest encapsulation efficiency (EE) (87.17%) and the lowest surface oil (31.66 mg/100 kg). Using nanoencapsulated fish oil in fermented milk significantly (p<0.05) increased the viability of Lactobacillus plantarum as well as eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) contents. The fermented milk sample containing fish oil nanoencapsulated with 25% wall material and 4% emulsifier yielded the greatest probiotic bacterial count (8.41 Log CFU/mL) and the lowest peroxide value (0.57 mEq/kg). Moreover, this sample had the highest EPA and DHA contents. Utilizing this nanoencapsulated fish oil did not adversely affect fermented milk overall acceptance. Therefore, it can be used for fortification of low fat probiotic fermented milk.

• Membrane and Water Treatment
• /
• v.7 no.3
• /
• pp.175-191
• /
• 2016

In this work, oil-in-water emulsions (O/W) were prepared successfully by membrane emulsification with $0.5{\mu}m$ pore size membrane. Sunflower oil was emulsified in aqueous Tween80 solution with a simple crossflow apparatus equipped with ceramic tube membrane. In order to increase the shear-stress near the membrane wall, a helical-shaped reducer was installed within the lumen side of the tube membrane. This method allows the reduction of continuous phase flow and the increase of dispersed phase flux, for cost effective production. Results were compared with the conventional cross-flow membrane emulsification method. Monodisperse O/W emulsions were obtained using tubular membrane with droplet size in the range $3.3-4.6{\mu}m$ corresponded to the membrane pore diameter of $0.5{\mu}m$. The final aim of this study is to obtain O/W emulsions by simple membrane emulsification method without reducer and compare the results obtained by membrane equipped with helix shaped reducer. To indicate the results statistical methods, $3^p$ type full factorial experimental designs were evaluated, using software called STATISTICA. For prediction of the flux, droplet size and PDI a mathematical model was set up which can describe well the dependent variables in the studied range, namely the run of the flux and the mean droplet diameter and the effects of operating parameters. The results suggested that polynomial model is adequate for representation of selected responses.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.551-559
• /
• 1997

The stability of liquid membrane in the extraction process was investigated through the extraction of the Zn component by using W/O/W emulsion type liquid surfactant membrane which was $D_2EHPA-Kerosene-Span$ $80-H_2SO_4$ system. The highest stability for liquid membrane through the Zn extraction process was obtained under the following conditions. That conditions were that span 80 concentration, as surfactant, of 2~3 vol.%;$D_2EHPA$ concentration, as extractant, of 5~7 vol.%;paraffin oil concentration, as membrane strengthening agent, of 10 vol.%;emulsion volume ratio to the external aqueous phase volume of 0.1, and internal aqueous phase volume ratio to the organic phase volume of 1.0.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.733-737
• /
• 2012

This study reports the microfluidic preparation of monodisperse multiple emulsions using hydrodynamic control. To generate multiple emulsions, we fabricate a microfluidic capillary device based on co-flowing stream without any surface modification of microchannels. Based on the system, we can successfully generate multiple emulsions (W/O/W) using water containing 0.5 wt% Tween 20, n-hexadecane with 5 wt% Span 80, and 10 wt% poly (vinyl alcohol) (PVA) aqueous solution, respectively. Furthermore, we control the number of inner droplets by modulation of flow rate of inner fluid at fixed flow rate of middle and outer fluid. The multiple emulsions having precisely controlled inner droplets' size and number can be applicable for multiple chemical reactions as an isolated microreactor.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.511-516
• /
• 2005

In this work, the crosslinked-chitosan microcapsules containing fragrant oil were prepared by oil-in-water-in-oil (O/W/O) multi-emulsion method. The effects of concentration of fragrant oil and stirring rates on the preparing of the microcapsules were investigated. The diameter and form of the microcapsules were observed by scanning electron microscope (SEM). As a result, the average particle size of microcapsules was decreased with increasing the stirring rate. The formation of chitosan microcapsules was comfirmed by FT-IR. The inclusion of fragrant oil into chitosan microcapsules was determined in the presence of specific peak of fragrant oil, i.e., $1,460cm^{-1}$, $2,960cm^{-1}$. Also, the release behavior or profile of fragrant oil from chitosan microcapsules was examined with UV/vis spectra. Released amounts of fragrant oil were increased with increasing as the content of fragrant oil and decreasing the pH.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.76-82
• /
• 2015

W/O emulsions were prepared from the aqueous solution containing NIPAAm, MBA, and APS in the continuous phase of toluene and mineral oil mixture with HMP and Span80 by using SPG membrane emulsification, and followed by the formation of PNIPAAm hydrogel microspheres through UV photopolymerization. As the ratio of mineral oil to toluene increased in the continuous phase, both particle size of the hydrogel increased and density of PNIPAAm polymer in the hydrogel particle increased, and which significantly affected swelling/deswelling ratio ($V/V_o$) with temperature change around VPTT. When the polymerization temperature was below LCST ($20^{\circ}C$), PNIPAAm hydrogel showed filled particle morphology; however, it was turned out to hollow particle morphology with thick shell layer with $40^{\circ}C$. Both density of PNIPAAm and gel content of the hydrogel increased with the increase in MBA concentration.

• Polymer(Korea)
• /
• v.33 no.1
• /
• pp.7-12
• /
• 2009

PLGA microspheres have been known as an injectable system for tissue engineering. The purpose of this study was to investigate the condition of emulsion formation and cell adhesion on the microsphere surface. BSA-loaded PLGA microsphere was fabricated by oil-in-water (O/W) and water-in-oil-in-water (W/O/W) solvent evaporation method. Sodium alginate was dissolved in water phase to control initial burst release and to improve lag time by PLGA bulk degradation. In addition, the morphology of cells attached on the micro spheres was studied using a scanning electron microscopy (SEM). Cellular proliferation behavior of human disc cells cultivated on PLGA micro spheres was analyzed using a MTT assay. MTT assay revealed that the cells can attach and proliferate on PLGA microspheres. According to these results, we concluded that BSA -loaded alginate/PLGA microspheres can be used as an injectable system for tissue engineering application.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.656-663
• /
• 2014

Atorvastatin calcium-loaded polyoxalate (POX) microspheres were prepared by an emulsion solvent-evaporation/ extraction method of oil-in-oil-in-water ($O_1/O_2/W$) for sustained release. We investigated the release behavior according to initial drug ratio, molecular weight ($M_w$) and concentration of POX and concentration of emulsifier. The microsphere was characterized on the surface, the cross-section morphology and the behavior of atorvastatin calcium release for 10 days by scanning electron microscopy (SEM) and high performance liquid chromatography (HPLC). The analysis of crystallization was analyzed to use X-ray diffraction (XRD), differential scanning calorimeter (DSC) and Fourier transform infrared (FTIR). These results showed that the release behaviors can be controlled by preparation conditions.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.3
• /
• pp.247-258
• /
• 2023

This study aims to investigate the enhancement of water resistance and improvement in adhesion to the skin by combining dextrin palmitate and isopropyl titanium triisostearate coating materials with titanium dioxide. Due to the recent increase in consumers who enjoy outdoor activities, the demand for sunscreen with excellent water resistance is increasing. Prior research was conducted with O/W, Pickering, and W/O/W multiple formulations, but there was a limit to water resistance. The purpose of this study is to develop a complex inorganic powder that can improve water resistance and increase adhesion to the skin to solve this problem. First, we combined dextrin palmitate and isopropyl titanium triisostearate coating materials to form a composite with titanium dioxide. The coating of the inorganic powder was confirmed using FE-SEM and FT-IR analysis. The composite exhibited significantly higher in vitro water resistance compared to other formulations. The hydrophobicity of the coated inorganic powder was compared by measuring the contact angles. When the coated inorganic powder was applied to the W/O sunscreen formulation and the non-coated inorganic powder was applied to the W/O sunscreen formulation as a control, the SPF of the sunscreen containing the coated inorganic powder was higher. These results were the same when observed with a UV camera. Finally the adhesion of the coated inorganic powder to the skin was assessed by applying it to a foundation product. In vivo study, it was observed that the product formulated with the coated powder exhibited less smudging compared to the foundation product formulated with the non-coated powder. The developed inorganic powder in this study demonstrated excellent adhesion to the skin, providing a superior sensory experience, as well as enhanced hydrophobicity and remarkable water resistance effects. In the future, the result of this study is expected to help develop various sunscreen products to improve water resistance.