• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.783-786
• /
• 1998

We designed a 3.3 V, 400 Mbps IEEE-1394 physical layer transeiver on 0.6um 1P3M CMOS process. The transceiver drives a twisted pair cable of which differential impedance is 110 $\Omega$ so that differential amplitude reaches 200 mV at 400 Mbps and restores this small signal to rail-to-rail. Also, the transceiver arbitrates the interface among nodes on a bus configuration and supports both synchronous interface and asynchronous interface.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1391-1393
• /
• 2008

In this paper, the long-term reliability for 1.25G transceiver in use of high speed optical access network is investigated. High temperature storage tests and accelerated life tests are used to long-term reliability. Accelerated aging test have been during 3,000 hour of the three accelerated aging conditions by caused high temperature stress. Mean life is assumed to follow the Arrhenius relationship and analysis from the failure data obtained in the accelerated aging conditions.

• ETRI Journal
• /
• v.26 no.6
• /
• pp.605-614
• /
• 2004

In this paper, we investigate array calibration algorithms to derive a further improved version for correcting antenna array errors and RF transceiver errors in CDMA smart antenna systems. The structure of a multi-channel RF transceiver with a digital calibration apparatus and its calibration techniques are presented, where we propose a new RF receiver calibration scheme to minimize interference of the calibration signal on the user signals. The calibration signal is injected into a multi-channel receiver through a calibration signal injector whose array response vector is controlled in order to have a low correlation with the antenna response vector of the receive signals. We suggest a model-based antenna array calibration to remove the antenna array errors including mutual coupling errors or to predict the element patterns from the array manifold measured at a small number of angles. Computer simulations and experiment results are shown to verify the calibration algorithms.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1155-1160
• /
• 2011

The importance of broadband wireless communication implemented at subway tunnels is growing up. At 18GHz wireless video transmission system, the transmitter requires a digital modulation method. At subway tunnel, A 18GHz's influence of the multi-pass padding is strong. OFDM digital modulation that is strong for multi-pass padding is recommended. Duplexing methode uses FDD to transmit and receive broadband data at the same time. In the case of FDD we assign a private use channel each with the transmission at the receiving. In this paper, We implement multiple access wireless OFDM transceiver. We verified that one ground transceiver communicates with two car transceiver at the same time.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1008-1013
• /
• 2011

The importance of broadband wireless communication system at subway tunnels is growing up. At 18GHz wireless video transmission system, the transmitter requires a digital modulation method. At subway tunnel, A 18GHz's influence of the multi-pass padding is strong. OFDM digital modulation that is strong for multi-pass padding is recommended. Duplexing methode uses FDD to transmit and receive broadband data at the same time. In the case of FDD we assign a private use channel each with the transmission at the receiving. In this paper, We implement multiple access wireless OFDM transceiver. We verified that one ground transceiver communicates with two car transceiver at the same time.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.426-432
• /
• 2012

A fully-integrated low power K-band radar transceiver in 130 nm CMOS process is presented. It consists of a low-noise amplifier (LNA), a down-conversion mixer, a power amplifier (PA), and a frequency synthesizer with injection locked buffer for driving mixer and PA. The receiver front-end provides a conversion gain of 19 dB. The LNA achieves a power gain of 15 dB and noise figure of 5.4 dB, and the PA has an output power of 9 dBm. The phase noise of VCO is -90 dBc/Hz at 1-MHz offset. The total dc power dissipation of the transceiver is 142 mW and the size of the chip is only $1.2{\times}1.4mm^2$.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1185-1188
• /
• 2003

This paper describes a design for a 2.5Gb/s serial data link CMOS transceiver based on the InfiniBand$^{TM}$ specification. The transceiver chip integrates data serializer, line driver, Tx PLL, deserializer, clock recovery, and lock detector. The designed transceiver is fabricated in a 0.25 ${\mu}{\textrm}{m}$ CMOS mixed-signal, 1-poly, 5-metal process. The first version chip occupies a 3.0mm x 3.3mm area and consumes 450mW with 2.5V supply. In 2.5 Gbps, the output jitter of transmitter measured at the point over a 1.2m, 50Ω coaxial cable is 8.811ps(rms), 68ps(p-p). In the receiver, VCO jitter is 18.5ps(rms), 130ps(p-p), the recovered data are found equivalent to the transmitted data as expected. In the design for second version chip, the proposed clock and data recovery circuit using linear phase detector can reduce jitter in the VCO of PLL.L.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.5
• /
• pp.482-491
• /
• 2013

This paper explains modeling and analysis of RC-dominant wires for high-speed wireline transceiver design. A closed form formula derived from telegrapher's equation accurately describes a frequency response of an RC-dominant wire, yet it is simple and intuitive for designers to easily understand design trade-offs without a complex numerical equation solver. This paper explains how the model is derived and how it can help designers in example transceiver designs.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.12
• /
• pp.5015-5027
• /
• 2015

Transceiver optimization in multiple input multiple output (MIMO) cognitive systems is studied in this paper. The joint transceiver beamformer design is introduced to minimize the transmit power at secondary base station (SBS) while simultaneously controlling the interference to primary users (PUs) and satisfying the secondary users (SUs) signal-to-interference-plus-noise ratio (SINR) based on the convex optimization method. Due to the limited cooperation between SBS and PUs, the channel state information (CSI) usually cannot be obtained perfectly at the SBS in cognitive system. In this study, both perfect and imperfect CSI scenarios are considered in the beamformer design, and the proposed method is robust to CSI error. Numerical results validate the effectiveness of the proposed algorithm.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.417-420
• /
• 2001

In this paper, a transceiver using waveguide modules for 60 GHz band wireless LAN is implemented and analyzed. The characteristics of millimeter-wave transmitter are 0 dbm output power, 10.5 dB gain and 38 dBc spurious emition. The receiver's are 3.16 dB noise figure, 8.8 dB gain, -86dBm sensitivity. Maximum communication distance is more than loom. Intermediate frequency comply with IEEE 802.11b. The transfer of multimedia files is performed. The transceiver's data rate can vary with intermediate frequency bandwidth and the transceiver is designed more than 200 Mbps.