• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.702-713
• /
• 2018

Power loss reduction and total harmonic distortion(THD) minimization are two important goals of improving three-level inverters. In this paper, an optimized pulse width modulation (PWM) strategy that can reduce switching losses and balance the neutral point with an optional THD of three-level neutral-point-clamped inverters is proposed. An analysis of the two-level discontinuous PWM (DPWM) strategy indicates that the optimal goal of the proposed PWM strategy is to reduce switching losses to a minimum without increasing the THD compared to that of traditional SVPWMs. Thus, the analysis of the two-level DPWM strategy is introduced. Through the rational allocation of the zero vector, only two-phase switching devices are active in each sector, and their switching losses can be reduced by one-third compared with those of traditional PWM strategies. A detailed analysis of the impact of small vectors, which correspond to different zero vectors, on the neutral-point potential is conducted, and a hysteresis control method is proposed to balance the neutral point. This method is simple, does not judge the direction of midpoint currents, and can adjust the switching times of devices and the fluctuation of the neutral-point potential by changing the hysteresis loop width. Simulation and experimental results prove the effectiveness and feasibility of the proposed strategy.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.496-503
• /
• 2010

The implementation of a RF transceiver for WRAN(Wireless Regional Area Network) system based on IEEE 802.22 standard using Cognitive Radio technology is presented in this paper. A CMOS RF transceiver IC for WRAN system operates in VHF/UHF(54~862MHz) broadband, and employs dual-path direct-conversion configuration and the in-band harmonic distortions are effectively suppressed by exploiting the dual-path direct conversion architecture. For 64QAM(3/4 coding rate) OFDM signal, an EVM of <-31.4dB(2.7%) has been achieved at 10dBm off-chip PA output power and the total chip area with pads is 12.95 mm2. The experimental results show that the proposed CMOS RF transceiver IC has perfect performance for WRAN system based on TDD(Time Division Duplex) mode.

• Earthquakes and Structures
• /
• v.11 no.1
• /
• pp.83-107
• /
• 2016

In this study, the response and behavior of machine foundations resting on dry and saturated sand was investigated experimentally. A physical model was manufactured to simulate steady state harmonic load applied on a footing resting on sandy soil at different operating frequencies. Total of (84) physical models were performed. The parameters that were taken into consideration include loading frequency, size of footing and different soil conditions. The footing parameters are related to the size of the rectangular footing and depth of embedment. Two sizes of rectangular steel model footing were used. The footings were tested by changing all parameters at the surface and at 50 mm depth below model surface. Meanwhile, the investigated parameters of the soil condition include dry and saturated sand for two relative densities; 30 % and 80 %. The dynamic loading was applied at different operating frequencies. The response of the footing was elaborated by measuring the amplitude of displacement using the vibration meter. The response of the soil to dynamic loading includes measuring the stresses inside soil media by using piezoelectric sensors. It was concluded that the final settlement (St) of the foundation increases with increasing the amplitude of dynamic force, operating frequency and degree of saturation. Meanwhile, it decreases with increasing the relative density of sand, modulus of elasticity and embedding inside soils. The maximum displacement amplitude exhibits its maximum value at the resonance frequency, which is found to be about 33.34 to 41.67 Hz. In general, embedment of footing in sandy soils leads to a beneficial reduction in dynamic response (displacement and excess pore water pressure) for all soil types in different percentages accompanied by an increase in soil strength.

• Korean journal of food and cookery science
• /
• v.26 no.4
• /
• pp.347-357
• /
• 2010

This study was assessed the menu satisfaction and preferences of high school boarding students in Gyeongggido. Data collection was carried out through surveys given to 300 high school boarding students; a total of 274 were usable. Statistical analyses were done using the SAS package program (version 8.2 for Windows). The results of this study are summarized as follows: 54.0% of respondents were freshman and 46.0% were sophomores: and 52.9% of respondents were male and 47.1% were female. According to the results of the menu satisfaction survey, males and females significantly differed on appropriate food temperature, freshness of food, harmonic combination of menu, menu variety, quality of ingredients, appearance of food, and frequency of supplied nutrition information. A significant difference regarding menu satisfaction was also found between grade level. First grade students were more satisfied than second grade students. Moreover, menu preferences were significantly high for omelet-rice, fried rice, pork-on-the-bone soup, deep-fried chicken, fruit salad, spicy chinese cabbage salad kimchi, chinese cabbage kimchi, and all desserts. On the other hand, pumpkin and rice porridge, beef and rice porridge, barley rice, soft tofu stew, soybean paste soup, braised japanese spanish mackerel, and sauteed squash were not significantly preferred. The results showed that high school boarding students' menu preferences differed depending on gender, grade, and boarding period. In conclusion, the results of this study should provide dieticians information for improving menu planning. In addition, foodservice satisfaction of the boarding school students can be improved by continuous menu improvement.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.86-93
• /
• 2018

In this work, control methods and operating modes are proposed to manage standalone microgrid. A standalone microgrid generally consists of two sources, namely, battery energy storage system (BESS) and diesel generator (DG). BESS is the main source that supplies active and reactive power regardless of load conditions, whereas DG functions as an auxiliary power source. BESS operates in a constant voltage constant frequency (CVCF) control, which includes proportional-integral + resonant controller in a parallel structure. In CVCF control, the concept of fundamental positive and negative transformation is utilized to generate a three-phase sinusoidal voltage under imbalanced load condition. Operation modes of a standalone microgrid are divided into three modes, namely, normal, charge, and manual modes. To verify the standalone microgrid along with the proposed control methods, a demonstration site is constructed, which contains 115 kWh lead-acid battery bank, 50 kVA three-phase DC - AC inverter, and 50 kVA DG and controllable loads. In the CVCF control, the total harmonic distortion of output voltage is improved to 1.1% under imbalanced load. This work verifies that the standalone microgrid provides high-quality voltage, and three operation modes are performed from the experimental results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.12
• /
• pp.2489-2497
• /
• 1994

This paper presents the development of a 10 W solid-state hybrid power amplifier(SSPA). operating over $7.7\sim8.5GHz$. The fabrication and measurement of this amplifier are performed with 3 sections, such as the front one for high gain, the middle one for driving, and high power one, to minimize the risk of failure and to increase the easiness of development. and then the final amplifier is realized by connecting 3 sections above mentioned, DC bias circuit, and temperature compensation circuit on one housing. Total small signal gain obtained is about $45\pm1dB$, the input and output return losses are 25 and 27 dB respectively. The output power measured at 1 dB gain compression point for 3 frequencies at 7.7, 8.1, and 8.5 GHz are $39.8\sim40.4dBm$, which is about 10 W. and the 3rd-order harmonic powers of 2 tones test are 13.34 dBc at output power 37.5 dBm. These obtained results satisfies the initially required specification. and the realized SSPA can be installed as a subsystem of the microwave transponder for telecommunication.

• Structural Engineering and Mechanics
• /
• v.52 no.3
• /
• pp.485-505
• /
• 2014

This study aimed to develop an approach to accurately predict the wind models and wind effects of large wind turbines. The wind-induced vibration characteristics of a 5 MW tower-blade coupled wind turbine system have been investigated in this paper. First, the blade-tower integration model was established, which included blades, nacelle, tower and the base of the wind turbine system. The harmonic superposition method and modified blade element momentum theory were then applied to simulate the fluctuating wind field for the rotor blades and tower. Finally, wind-induced responses and equivalent static wind loads (ESWL) of the system were studied based on the modified consistent coupling method, which took into account coupling effects of resonant modes, cross terms of resonant and background responses. Furthermore, useful suggestions were proposed to instruct the wind resistance design of large wind turbines. Based on obtained results, it is shown from the obtained results that wind-induced responses and ESWL were characterized with complicated modal responses, multi-mode coupling effects, and multiple equivalent objectives. Compared with the background component, the resonant component made more contribution to wind-induced responses and equivalent static wind loads at the middle-upper part of the tower and blades, and cross terms between background and resonant components affected the total fluctuation responses, while the background responses were similar with the resonant responses at the bottom of tower.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.109-116
• /
• 2014

This paper presents a high-efficiency digital class-D audio amplifier using a composite interpolation filter for portable audio devices. The proposed audio amplifier is composed of an interpolation filter, a delta-sigma modulator, and a class-D output stage. To reduce power consumption, the designed interpolation filter has an optimized composite structure that uses a direct-form symmetric and Lagrange FIR filters. Compared to the filters with homogeneous structures, the hardware cost and complexity are reduced by about half by the optimization. The coefficients of the digital delta-sigma modulator are also optimized for low power consumption. The class-D output stage has gate driver circuits to reduce shoot-through current. The implemented class-D audio amplifier exhibited a high efficiency of 87.8 % with an output power of 57 mW at a load impedance of $16{\Omega}$ and a power supply voltage of 1.8 V. An outstanding signal-to-noise ratio of 90 dB and a total harmonic distortion plus noise of 0.03 % are achieved for a single-tone input signal with a frequency of 1 kHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.3
• /
• pp.44-53
• /
• 2008

In this paper, we present the design of delta-sigma modulation-based class-D amplifier for driving headphones in portable audio applications. The presented class-D amplifier generates PWM(pulse width modulation) signals using a single-bit fourth-order high-performance delta-sigma modulator. To achieve a high SNR(signal-to-noise ratio) and ensure system stability, the locations of the modulator loop filter poles and zeros are optimized and thoroughly simulated. The test chip is fabricated using a standard $0.18{\mu}m$ CMOS process. The active area of the chip is $1.6mm^2$. It operates for the signal bandwidth from 20Hz to 20kHz. The measured THD+N(total harmonic distortion plus noise) at the $32{\Omega}$ load terminal is less than 0.03% from a 3V power supply.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.168-180
• /
• 2018

In order to achieve the high quality output voltage of single-phase voltage source inverters, in this paper an Adaptive Complementary Sliding Mode Control (ACSMC) is proposed. Firstly, the dynamics model of the single-phase inverter with lumped uncertainty including parameter variations and external disturbances is derived. Then, the conventional Sliding Mode Control (SMC) and Complementary Sliding Mode Control (CSMC) are introduced separately. However, when system parameters vary or external disturbance occurs, the controlling performance such as tracking error, response speed et al. always could not satisfy the requirements based on the SMC and CSMC methods. Consequently, an ACSMC is developed. The ACSMC is composed of a CSMC term, a compensating control term and a filter parameters estimator. The compensating control term is applied to compensate for the system uncertainties, the filter parameters estimator is used for on-line LC parameter estimation by the proposed adaptive law. The adaptive law is derived using the Lyapunov theorem to guarantee the closed-loop stability. In order to decrease the control system cost, an inductor current estimator is developed. Finally, the effectiveness of the proposed controller is validated through Matlab/Simulink and experiments on a prototype single-phase inverter test bed with a TMS320LF28335 DSP. The simulation and experimental results show that compared to the conventional SMC and CSMC, the proposed ACSMC control strategy achieves more excellent performance such as fast transient response, small steady-state error, and low total harmonic distortion no matter under load step change, nonlinear load with inductor parameter variation or external disturbance.